Recent content by cbubu

fenix-store
  1. cbubu

    Energizer Hard Case Professional LED Headlight

    I bought this light few days ago and the "the tab on the diffuser" was painted out of the box! Not a bad light :sssh: Best Regards :)
  2. cbubu

    My TA30 went to the Dentist ...

    I don't really "cut" the teeth, it is more like "sand" : I put the TA30 in front of the sand disk of a dremel and push the TA30 slowly. With this way the surface stays plane. Put tape in front of the lens and around the ring selector of level if you plan to do it. Sorry for my English ... below...
  3. cbubu

    My TA30 went to the Dentist ...

    It was my fist intention to completely remove the "teeth" ... but the nice looking in this configuration and the fact that I still can check if the light is on or off when it is standing on the bezel (look at the 4th picture) make me stop :drool: I did that about 2 weeks ago and I wanted to see...
  4. cbubu

    My TA30 went to the Dentist ...

    My TA30 went to the Dentist ... Two weeks ago I decided to send my Fenix TA30 to the dentist ... (risk of injury, stress at the airport, ...) the TA30 is a great light but the "crenellated striking bezels" are not for me ... The result is not so bad : smooth feeling, great looking :-)
  5. cbubu

    Any TK40's out there had any accidents?

    Check this tread and you will sleep happy :) My Extreme Fenix TK40 Torture Test. Regards,
  6. cbubu

    Fenix L1D/T: Rebel vs Q2 vs Q5?

    The L1T V2 with a rebel 80 is the light I keep in my jacket: great light, simple UI, great beam and a nice warm tint. As you notice the low setting is a much more a "medium" setting but it's ok for me. The Fenix red filter fits perfectly and can decrease sufficiently the output. Whatever, every...
  7. cbubu

    A2 Aviator tailcap issue ... maybe?

    Hi Dan, I had the same issue few months ago, but in my case the switch wasn't working great anymore : I needed to switch on / switch off several times to have the normal output of the incandescent bulb (otherwise I had a very dim output as if the batteries were nearly empty). The change of...
  8. cbubu

    Help me pick a 2AA light

    Selfbuilt did an awesome review of the 2AA (in the reviews forum): http://candlepowerforums.com/vb/showthread.php?t=214890 It can help you to decide :twothumbs Regards,
  9. cbubu

    sanyo AA (2000 mAh ) to power led flashlight

    For High current nimh perform much better than regular alkalines : here an example of runtime I did for the Fenix E20 : Regards,
  10. cbubu

    Fenix Lego : compatibility chart

    :twothumbs Fenix Lego ... here is the compatibility chart I found playing with my lights : Regards,
  11. cbubu

    Fenix E20 why so little about it on the board?

    Here some reviews : http://candlepowerforums.com/vb/showthread.php?t=204220 http://www.candlepowerforums.com/vb/showthread.php?t=207982 Regards,
  12. cbubu

    Fenix TK20: Is the Hype in the Light?

    Here are the runtimes : Tk20 runtime with energizer lithium batteries on High (about 2:05 to 50%) In Hours: In minutes: not so bad :sssh: Regards,
  13. cbubu

    My Fenix E20, TK20 beamshots and runtimes

    Thanks Chao!!! Your pictures are great ! the comparison with the MiniMag is impressive :-) Regards,
  14. cbubu

    Led Lenser Frogman mod?

    I have an older version of this light with an old luxeon LED. I found that there'nt any regulation circuit but just a resistor ... I changed the LED for a SSC P4 (but you don't have to if you get a Cree version) and add a circuit board (750 mAh). This is what I think you can do : change the...
  15. cbubu

    Fenix PD30, PD20, LD10 and LD20

    Re: New Fenix models PD30, PD20, LD10 (thx devine) and LD20 (thx Marduke) I agree with 4sevens :) The output/runtimes just seem to be more realistic :) Regards,
See more

Latest posts

Top