This 1.5V Step-up driver is from a Lumintop AAA flashlight.
I will try to change the modes, if I can access the microcontroller...
One IC is the Step-up driver, the other a microcontroller.
Can anyone identify both sot23-6 IC's?
Markings: CFC4w & 0WJ or 0(null)WJ
Re: AWR hotwire driver. I could use some help please :)
I have a printed wiring manual in black/white from 2006 :faint:, I can make a pdf and upload to a filehoster.
Ok? (Need 2 days)
I read a little bit about VFD EMV & some "noise", who can trip circuit breaker & RCD's from the powersource. --> I don't wan't to blackout the whole apartment block :)
I saw in a action board a Danfoss VLT 2815 with a integrated RFI-Filter (class 1a) & brake.
The motor cable will be less than 2...
Thanks for the ideas and input's!
I have searched some transformers but I couldn't find any 230v-to-460v above 100va in auctions board. Maybe they are here not so common in my country.
A 1.5kva VFD in auctions are available for less then 150$. Maybe I search a motor with a higher va rating at...
I have to move my lathe to a new location, but there I have no access to 3 Phase 380V Mains.
Only 1 Phase 230V 10A is aviable.
Is that possible to wire the existing motor with a Inverter? Which is the right Inverter for the motor?
(The capacitor-trick is maybe not the right solution...
Hi Pablo,
Sorry for the late reply, my mailbox was full ;)
I will make it für 35.- incl. shipping.
About the height for the led: Für the Luxeon 5 its 20mm, I would say emitter + die height = 3mm
For a XP-G2 with 1.5mm sinkpad its 1.5 + 0.8 = 2.3mm. So for a XP-G2 the total height would be...
Recently I rebuilt two cordless from ni-cd to li-lion.
I found a good battery seller with tabs-service.
http://www.ebay.com/itm/321080176476?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Also with a Bosch 12v drill with flat LiFePo4 batteries...
I'm trying to build a cordless drill with a integrated USB Li-Ion charger (TP4056 with 1A charge current)
The Battery is a high-drain Li-Ion with 20A continuous discharge current and 2Ah capacity.
I have everything to start but I'm asking me if its a good idea to let the charger permanent...
I will use a XR-E Emitter again, I like the good throw.
Tried other LED's like XP-E & XM-L: The result is clearly, TIR-optic is made only for the XR-E.
A Q5 or R2 with a WG-bin would be nice, like this one:
http://dx.com/p/cree-xr-e-r2-wg-emitter-on-premium-star-15943
A PCB who is thinner and...
I cuted a ring from a aluminium pipe who fits on the thread, made a side cut and put in the 3 jaw chuck.
Tighten the chuck firmly and put some new rubber and cord on the bezel.
........Success :)
The Emitter is completely yellow inside, including the bond-wires, perhaps a P4-Bin.
Thanks...
Thanks for the reply, I tried it but it always touched the side of the head and the thread with the pliers :(
I tried different strings.
Also when heated up to 100°C, the rubber from the bycycle hose slips more one the bezel. --> I should get a real strap wrench.
I should do a adapter with a...
Today I opened a old Cree KX2 head without before heating them up.
(With this method: http://www.candlepowerforums.com/vb/showthread.php?310947-Opening-lights-with-glued-threads-HOWTO-without-tools-no-damage)
This came out:
Instead the bezel came off, it only opened a spacer.
Now my...
@Norm: I testet it with 3 Multimeters and the Futaba CDR5000: average value: 4.12V = 0.01V wrong, the second module: 4.13V = 0.00V wrong.
@Microa: Maximum battery length: 70mm
I was never happy with many cheap 18650 charger because I never know if the circuit really stops at 4.2 - 4.25V
or a bad power supply with a high impact to the battery.
So I bought this "housing":
http://dx.com/p/single-18650-17670-lithium-battery-charger-1a-charging-current-5837
For...
I have no experience with wood turning, only in metal.
If the the shaft of a small lathe is only driven by belts, its quieter than a cordless screwdriver.
With feed activated and an uncooled gearbox (no oil) the noise noticeable louder.