FF call is lumenator
Don, I have sent you two emails at your pacbell.net address and it keeps coming back as "Undeliverable to the intended recipient".
PM me on how to proceed.
Proud custodian of Tvodrd`s works of art; Peter`s Arc`s and Brass Arc AAA; Mike Jordan`s gems; some really great lights from Enrique, Fred and Tain ....and *several* of Don`s mods, Ti`s and McLux masterpieces.
I'll get to the open orders in a bit. Thanks.
I checked my spam file as well and nothing from you so I don't know what is happening. Try sending to
This has worked for others who were getting blocked out.
Checked into it, the problem was with our email server. Trying once again.
Added: 17:09 CDT Paypal sent! Thanks Don.
Last edited by Cowley; 07-08-2008 at 04:05 PM.
Since Don seemed to skip over this question I will answer it for him.
It is clear that Don's focus if on titanium flashlights. He used to make them in aluminum but that time has clearly passed.
It doesn't make economic sense for him to make lights or sub assemblies in aluminum.
I will toss a guess out there and say that the aluminum aleph sets we say several months ago were the last aluminum parts we will see from don fir some time.
You may be able to ask don to sell you a aleph mule set. have the oil can finish stripped and then anodize it at your local metal finishing shop.
Support your local flashlight builder.
Buy American. Stop crying and start Buying.
Flashlights are tools. Period.
As it should be, IMO. Don calls these a tool to be used, and mine (as well as most others) see daily use, some in harsh environments. Mine get covered in oils, greases, detergents, etc., and show no effect at all. In addition to toughness, the lack of reactivity with acids, bases, and most chemicals makes Ti a super choice for a work light.It is clear that Don's focus is on titanium flashlights.
My aluminum lights live a more gentle life. There's always either a Nautilus, Ion, or Aeon in the right front pocket, and these see daily use as well. But, if my right hand isn't clean, it doesn't grab for that light - it picks out the SunDrop or the LS20.
Different tools for different uses.
Aluminum oxide, either by virtue of anodizing where an even and hard film is induced by high current or from sitting exposed to air, is non electrically conductive. The McClickie pak requires electricity to enter into the pak where the ground ring of the Clickie switch is in contact with it and electricity will typically leave the pak at the front face on the lip of the pak. At these two areas, you want good low resistance and that means no oxidation and certainly no anodize. The aluminum McClickie paks I had made that were part of the Aleph Mule McClickie hosts were plated with nickel because nickel is a good and reasonably durable film which is electrically conductive. Titanium which oxidizes to some extent almost immediately when in the presence of oxygen is also electrically conductive.
A hard anodized McClickie pak would need to be raw Al or plated with something other than anodize at the electrical passage points. This would add to the cost of the parts and then what are they to be matched up with? Existing hard anodized heads from SF and others? Ha! Until I am blue in the face I will maintain that hard anodize is first and foremost a structural and durable film added to protect the raw Al substrate. It is not a cosmetic coating and yet a strong and verbal group on CPF insist otherwise. So be it!
I have some unwritten guidelines and priorities in what ever I am working on or bringing to CPF and in the case of hard anodize, I want the complete part hard anodized as I feel this allows for maximum protection of the part. The heads and sleeves of the Al PD sets were all anodized with no masking or breaking of the anodize film required. It also took me a few years to work through the first set of those parts which I had machined. Things were much slower back then with some improvements in the Luxeon LED's but that was about it in terms of technology change.
Any run in aluminum has to be in relative large numbers for me and this represents significant labor and assembly time. I have more than enough on my plate with the titanium which I prefer in terms of longevity and durability. As a niche, even the titanium is now being visited by many and I have to tread carefully!!
Yes, I skipped the question initially. Although I think hard anodize is a good and viable film for aluminum and I think aluminum is a good material for flashlights, if I can avoid building in the material and using anodize I will and gladly so. I am not sure I could even be civil to someone complaining about a cosmetic aspect of anodize to me and it is best I avoid any chance of this happening! My priorities are low to no maintenance both in the lights I build and cosmetic considerations for certain.
Some focus on the light itself and how it looks and feels. Some focus on the beam that comes from the light. My focus is on what the beam itself can and will do and with hopes that that beam will be there and available regardless of the time in service and environment the light is used in.
If a new and improved E-series head comes out 10 years from now, it is my hope and expectation that one of these Ti McClickie paks would be there and ready and able to serve as host to such a head. Scratches and dings and battle scars have nothing to do with its ability to "serve".
I'm crossing my fingers hoping I can get in on this!
"Et lux in tenebris lucet"
Thanks Don, got mine today, quick service to the mainland! It is beautiful as usual, and I can't wait to get it home and play with it.
Received the package very well.
Thank you, Don.
light your lite . ...
Arrived today, outstanding work as always Don!
Recieved my pack today. Thank you
Once things leave my hands I am not responsible for what happens.
Email send for one McClicky Pak
Don please let me know when you will ship...
Received the pack yesterday, and thanks again DON
-N O V E L-
for one Pak
Is this Aleph compatible? Could I buy a TI aleph compatible head and a LE, and use them with this McClickie pack? I don't want to use a head from my E1B - I wan't all Ti to keep my Ti PD-S company!
I'm new at this semi-custom thing...
I spend my days in the light thinking about flashlights in the dark
Yes, the Aleph and SureFire E series are compatible.
"Et lux in tenebris lucet"
Edited 07/16/08 1606 to add:
Last edited by wsmd; 07-16-2008 at 05:01 PM.
Cant wait to get mine...
Last edited by allthumbs; 07-19-2008 at 04:03 PM. Reason: Paypal sent
Received mine today
Unbelievable a true thing of beauty and function.
E-Mail sent for 1 and
Last edited by Steve L; 08-01-2008 at 05:14 PM.
I'm dying to get a custom body for my Boxter and I hope this isn't a stupid question but will an AW RCR123 fit in these? Thanks
An AW 123 fits fine in mine.
Last edited by beach honda; 08-11-2008 at 12:02 PM.
Got Lights? USE EM!!