FS: Aleph 1 Titanium Bezels

[arewethereyetdad]

I'd like to see those pics. I have an Aleph 1 arriving soon and will likely want a new bezel for it.

Yep, should be there tomorrow.

[fyrstormer]

I'll take one. Style 2, without the extra chamfers, brushed finish.

[fyrstormer]

In case anyone's on the fence about getting one of these, I offer up a couple of pics of the one I bought:





Good stuff.

[RPM]

Just found these in the garage! Bump

[Drywolf]

Do you have plain?

[RPM]

Yes, I have some plain with a straight wall on the OD. I'll add the pics asap.

R-

Do you have plain?

[Drywolf]

I'll take one of these.

Style 4) TI-1370-410-TP
Tapered O.D. Wall, Tall, Plain $30

PayPal in the morning..

[RPM]

Just making sure you know... #4 and #5 are for the larger diameter head of the McLuxIII-27LT. The diameter on the head of the 27LT was approx. 1 3/8" and the Aleph 1 heads are about 1 1/4"

I'll take one of these.

Style 4) TI-1370-410-TP
Tapered O.D. Wall, Tall, Plain $30

PayPal in the morning..

[Drywolf]

Just making sure you know... #4 and #5 are for the larger diameter head of the McLuxIII-27LT. The diameter on the head of the 27LT was approx. 1 3/8" and the Aleph 1 heads are about 1 1/4"

Yup this is meant for my 27LT-S. Thx.

[Drywolf]

I'll take one of these.

Style 4) TI-1370-410-TP
Tapered O.D. Wall, Tall, Plain $30

PayPaL sent....

[archimedes]

Do you still have a "Style 1" bezel in standard finish available ? .... I have an Aleph1 on the way

Also, to get out the old bezel retaining ring, will the standard Z44 tool fit ? Or is there some other recommended method ?

Thanks!

[fyrstormer]

I loosened my Aleph 1 bezel ring using a pair of jeweler's screwdrivers braced in my hand. It worked well enough for a single operation.

[archimedes]

I loosened my Aleph 1 bezel ring using a pair of jeweler's screwdrivers braced in my hand. It worked well enough for a single operation.

I've also got a pretty small pair of snap ring pliers that might be worth a try, I guess. I'd just rather use something more secure (& non-marring)....

[fyrstormer]

If you're only going to remove it once so you can install a new bezel, all you need to do is be extra-careful the one time. Maybe wrap the plier jaws in a bit of tape to prevent scuffing the anodizing.

[easilyled]

Do you still have a "Style 1" bezel in standard finish available ? .... I have an Aleph1 on the way

Also, to get out the old bezel retaining ring, will the standard Z44 tool fit ? Or is there some other recommended method ?

Thanks!

Have you tried the finger-nail method to begin with?

If you have strong finger-nails, use those belonging to your thumb and middle finger in the opposing grooves of the retaining ring and twist the light so that the ring rotates anti-clockwise relative to the light.

I found that this method worked quite well with most of my Aleph lights at the time although it resulted in a few chipped finger-nails.

[RPM]

Do you still have a "Style 1" bezel in standard finish available ? .... I have an Aleph1 on the way

Also, to get out the old bezel retaining ring, will the standard Z44 tool fit ? Or is there some other recommended method ?

Thanks!

Yes, a few of all styles in stock...

All my Aleph lights I bought back then already had the original retaining bezels removed once before so they were pretty easy to move. I just took a pair of needle nose pliers and locked the tips open at the right spacing with a screw and washers. I was lucky that they moved really easy and nothing got scratched.

R-

[archimedes]

Yes, a few of all styles in stock....

R-

for Style 1 Aleph1 bezel in standard finish. I added a bit extra for fees and such - if that might cover a DC# too, I would appreciate it.

EDIT - Arrived, thanks! (and installation was a breeze... ) .

[RPM]

for Style 1 Aleph1 bezel in standard finish. I added a bit extra for fees and such - if that might cover a DC# too, I would appreciate it.

Thanks for these ... any updates on tailcaps, by the way?

PM replied... Payment received... Thanks. This will ship Saturday.

R-