SunwayLED
Results 1 to 14 of 14

Thread: SOLD: Dafabricata P7 modded Gray KL4 Head only (stock board) *2nd price drop*

  1. #1
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default SOLD: Dafabricata P7 modded Gray KL4 Head only (stock board) *2nd price drop*

    This is the exact head as seen here:

    http://www.candlepowerforums.com/vb/...Rare-body-left

    It's in the same condition as above. Runs on 2 primaries or 1 li-ion. It puts a stock KL4 to shame

    SOLD Asking $95 $90 $85 shipped SOLD & Shipped!

    USPS Priority w/ DC CONUS Only
    Last edited by samuraishot; 07-14-2012 at 02:29 PM. Reason: SOLD

  2. #2
    Flashaholic* archimedes's Avatar
    Join Date
    Mar 2011
    Location
    CONUS, arteriosus
    Posts
    2,862

    Default

    Any idea of the current draw, or approximate lumen output ?

    Also, just one level, correct ?

    Direct drive, or regulated ?
    IF 2 = 1 THEN 1 = 0

  3. #3
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    Hi archimedes!

    Not too sure, I did a lot of research and couldn't really find much info on it.

    Anyhow, yes, it's one level - not too sure if it's DD or Regulated. It uses the stock board, but I'm not sure if that has anything to do with it being DD or Regulated.

    edit: Some sources say about 600 lumens
    Last edited by samuraishot; 07-13-2012 at 01:10 PM.

  4. #4
    Flashaholic* archimedes's Avatar
    Join Date
    Mar 2011
    Location
    CONUS, arteriosus
    Posts
    2,862

    Default

    Hmmm ... tempting

    Anything you could compare it to, in terms of informal "ceiling bounce test" for output?

    Maybe something standardized ... perhaps a SureFire, HDS, Malkoff, etc.

    Also, how's the tint? And is there a "P7 donut hole" in the center of the beam?

    Thanks for the info !
    IF 2 = 1 THEN 1 = 0

  5. #5
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    Quote Originally Posted by archimedes View Post
    Hmmm ... tempting

    Anything you could compare it to, in terms of informal "ceiling bounce test" for output?

    Maybe something standardized ... perhaps a SureFire, HDS, Malkoff, etc.

    Also, how's the tint? And is there a "P7 donut hole" in the center of the beam?

    Thanks for the info !
    It definitely lights up an entire room, that's for sure. In terms of tint, I have a Milky Expurgator with an XPG-R51C and the XPG is slightly cooler than the P7. The P7 has an ever so slight neutral tinge to it (at least to me). As for the donut hole, it's not too noticeable. I was going to stick some diffusing film over the lens, but later on I decided it was something I could live with.

  6. #6
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    PM sent & Price Drop!

  7. #7

  8. #8
    Flashaholic* archimedes's Avatar
    Join Date
    Mar 2011
    Location
    CONUS, arteriosus
    Posts
    2,862

    Default

    Quote Originally Posted by samuraishot View Post
    ....Asking $95 $90 $85 shipped

    USPS Priority w/ DC CONUS Only
    I wish I could resist, but at $85, I'll have to say ... I'll take it

    Please PM with PayPal info - thanks!
    IF 2 = 1 THEN 1 = 0

  9. #9
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board) *2nd price drop*

    Quote Originally Posted by archimedes View Post
    I wish I could resist, but at $85, I'll have to say ... I'll take it

    Please PM with PayPal info - thanks!
    I'm glad it's going to you, archimedes PM on the way with PayPal info!

  10. #10

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    Quote Originally Posted by samuraishot View Post
    Anyhow, yes, it's one level - not too sure if it's DD or Regulated. It uses the stock board, but I'm not sure if that has anything to do with it being DD or Regulated.
    The stock driver is a boost driver that ran a Luxeon V LED, whose Vf was around 6V.
    A Seoul P7 Vf at 3A drive is around 3.5V.

    I would run this light only with 1xLi-ion (e.g., a 17670). You will be in direct drive
    since Vbatt>Vf, and most likely the P7 will be pushed hard. I definitely would not
    use 2xIMR16340, which would probably fry the LED and/or driver. I also would
    not use 2x123A because the current draw would be excessive for those cells.

  11. #11
    Flashaholic* archimedes's Avatar
    Join Date
    Mar 2011
    Location
    CONUS, arteriosus
    Posts
    2,862

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    Quote Originally Posted by samuraishot View Post
    I'm glad it's going to you, archimedes PM on the way with PayPal info!
    ... pleased to be doing business with you again

    Quote Originally Posted by Justin Case View Post
    The stock driver is a boost driver that ran a Luxeon V LED, whose Vf was around 6V.
    A Seoul P7 Vf at 3A drive is around 3.5V.

    I would run this light only with 1xLi-ion (e.g., a 17670). You will be in direct drive
    since Vbatt>Vf, and most likely the P7 will be pushed hard. I definitely would not
    use 2xIMR16340, which would probably fry the LED and/or driver. I also would
    not use 2x123A because the current draw would be excessive for those cells.
    Yep, this is what I was thinking ....
    Last edited by archimedes; 07-23-2012 at 06:11 PM.
    IF 2 = 1 THEN 1 = 0

  12. #12
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    Quote Originally Posted by archimedes View Post
    ... pleased to be doing business with you again
    Got it, it'll be out tomorrow!

  13. #13
    Flashaholic* archimedes's Avatar
    Join Date
    Mar 2011
    Location
    CONUS, arteriosus
    Posts
    2,862

    Default Re: WTS: Dafabricata P7 modded Gray KL4 Head only (stock board)

    Just arrived .... Yep, it's BRIGHT!

    Thanks for the quick ship, and the little "extra"
    IF 2 = 1 THEN 1 = 0

  14. #14
    Flashaholic* samuraishot's Avatar
    Join Date
    Jul 2009
    Location
    L.A.
    Posts
    743

    Default

    Quote Originally Posted by archimedes View Post
    Just arrived .... Yep, it's BRIGHT!

    Thanks for the quick ship, and the little "extra"
    No problem, I'm glad it arrived safely! I kinda miss it now haha

    Enjoy!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •