NITECORE -- Keep Innovating
Results 1 to 14 of 14

Thread: "Thor K 2012" -An Lk14 build (600 watt Q4559X)

  1. #1
    Flashaholic Hoop's Avatar
    Join Date
    Dec 2011
    Location
    Spokane, WA
    Posts
    297

    Default "Thor K 2012" -An Lk14 build (600 watt Q4559X)

    Finally, after several months of acquiring parts and tools and putting this beast together, it is finished. It uses a 600 watt GE Q4559X 28v Par 64 lamp, regulated to 30 volts with JimmyM's JM-PhD-X1 voltage regulator. It is a single mode light, but I purchased a programmer so I can add modes later if I want. This is my first flashlight mod/build, and actually is the first project I've ever soldered as well. Picked up a Hakko fx-888 and it was easy peezy.

    Inspirational and historical credits:

    Original LarryK14 thread
    Petrev's "Thor X10 Mod"
    BVH's Regulated LarryK14

    Parts used in this build: (prices include shipping)
    -"Cyclops Thor X 10 Million Candle Power Spotlight." Purchased used on Ebay. =$30
    -GE Q4559X Par 64 Quartz Halogen Landing Lamp =$40
    -JimmyM's JM-PhD-X1 PWM Voltage Regulator =$85
    -2x ZIPPY Flightmax 5000mAh 6S1P 20C LiPo's =$100
    -2x C&K Components DM22J12S205PQ Double-Pole Single-Throw Rocker Switch =$15
    -Illuminated Momentary Pushbutton Switch, 22mm, Red LED, Stainless =$20
    -2x FrSky Lipo Voltage Sensor FLVS-01 =$30
    -2x 12" 6S JST-XH balance extension cable =$7
    -Anderson Power Pole Connectors =$10
    -12AWG silicone wire, 3 feet of black and red =$10
    -OP/TECH USA 0901012 S.O.S. Shoulder Strap =$25
    -2x Sunon 40mm 8200 RPM MagLev Fan (MB40201VX-G99) =$30
    -2x Black 40mm Fan Grill =$5
    -2x small plastic boxes (harvested lids for voltage display covers) =$9
    -Misc. Hardware (nuts and bolts for the fans, split rings for strap, etc.) =$5

    Total Cost of Materials: Roughly $421 USD

    --------------------------------------------------------------------------------------------

    The non functional (dead battery) host as seen on ebay:







    --------------------------------------------------------------------------------------------

    The build:
    (Not necessarily in chronological order, and some pics taken after light was completed because I didn't take pictures of everything I did during the build.)

    First I cut/ground off excess plastic from the body so that the bulb would fit under the bezel. I eventually cut more off than this picture shows. In the Thor's stock configuration, the plastic bezel is screwed into risers in the body, and the back of the bezel sits off of the body about an 1/8" [3mm]. The rubber shroud has a lip on it which fits between that 1/8 gap and a big lip on the body. You can see the lip on the body in the above picture of the stock "AC charger" ports. Conveniently, after cutting off the threaded risers such that the bezel sits flush on the body, the rubber shroud has enough length to wrap around the lip of the body. Because of this, I didn't have to use any screws to retain the bezel to the body. It is held tightly by the rubber shroud. I did however have to glue the bulb into the bezel. I used Silicone RTV and applied it liberally, also putting some on the bulb to prevent light from shining back into the body.







    BULB SHOT:


    Next to cut out the holes for the fans and voltage displays.




    Installed the fans and voltage displays. The fans are 40x20mm, 8200 rpm 12v fans and are said to produce 10.8 CFM air flow each, at 27.5 decibels. They are pretty quiet and their sound is not annoying.





    Next I cut out and painted a little plastic piece to cover the holes for the stock charge ports, then glued it in place.


    The voltage display covers are lids harvested from very small clear plastic boxes I found Amazon. Brass tacks cover the holes where the stand used to attach.





    The stock SPST rocker switches were replaced with double pole switches. The bottom switch turns the regulator board on. The fans and the illuminated switch run off of the 12v aux outputs on the JM-PhD-X1, so when the board comes on, so do they. The top switch is connected to the ground lead of each pack's balancing cable, one to each pole of the switch, and turns on the OLED voltage displays. Each lipo gets its own voltage display which shows the total voltage and individual cell voltages with a claimed +/- .03v accuracy.






    --------------------------------------------------------------------------------------------

    The finished light: (pics taken in direct sunshine which makes minor blemishes stand out)








    --------------------------------------------------------------------------------------------

    BEAMSHOTS!!!!!!!


    Its dark.



    Not so much anymore. Distance to the far fence is approximately 425 feet. [133 meters]



    Distance to the far fence is approximately 585 feet. [179 meters]




    Better beamshots to come...
    Last edited by Hoop; 05-06-2016 at 02:06 PM.

  2. #2
    Flashaholic Hoop's Avatar
    Join Date
    Dec 2011
    Location
    Spokane, WA
    Posts
    297

    Default Re: "Thor K 2012" -A Larryk14 build

    Ok I took better beamshots.

    ***Clicking on the photos will link you to the original size photo.***

    These are from specific locations so that I could get relatively accurate distance measurements from google maps.
    I used a Cannon Elph 300 HS, in night scene mode, mounted on a tripod with 2 second shot delay timer so as to avoid blur from shaking the camera. I think the pics are fairly close to what I see in real life, but the light is a bit brighter in person and with more appreciable side spill.

    Took an hour long walk with the lk14 on one shoulder and the Olight SR-90 on the other, and toting a tripod under my arm. Snapped a couple of SR-90 beamshots to the 962 foot barn. The SR-90 is pretty good out to 400 feet or so but it doesn't do much out at 300 years.

    Distance: 962 feet [292 meters] to that barn.
    SR-90 beamshots for comparison



    LK 14:


    The black figure is a horse.


    Distance: 1150 feet [350 meters] to the pole. That's a plowed field of brown dirt.


    Distance: 1300 feet [396 meters] to the railroad crossing.


    Distance: 830 feet [253 meters] to that house and outbuilding. The beam is aimed between the two structures but lights them both up.


    Trees in the distance on my left:


    Distant field and buildings to my right:
    Last edited by Hoop; 05-06-2016 at 01:18 PM.

  3. #3
    Flashaholic* jmpaul320's Avatar
    Join Date
    Mar 2012
    Location
    CT, USA
    Posts
    3,768

    Default Re: "Thor K 2012" -A Larryk14 build



    nice build!!

    i especially like that voltage monitor

  4. #4
    Flashaholic* tobrien's Avatar
    Join Date
    Dec 2005
    Location
    Georgia Highway 441
    Posts
    4,861

    Default Re: "Thor K 2012" -A Larryk14 build

    yeah that voltage monitor is insane!
    aka Edgar Allan Bro, Brosama Bin Liftin, Walter Crunkite, Bro Namath, Teddy Brosevelt, and the Tomahawk Crunkmissile.
    my lights - review of PrecisionWorks - that's Gucci Mane in my avatar

  5. #5

  6. #6

    Default Re: "Thor K 2012" -A Larryk14 build

    Great build very high quality, love those voltage displays too . I do not think i have seen a LarryK14 build for a while, so always nice to see.

  7. #7

    Default Re: "Thor K 2012" -A Larryk14 build

    VERY nice build! I love the voltage monitors and the two cute little fans. What type of runtimes are you getting with this setup?
    Who needs to see the light at the end of the tunnel when you have friends on CPF?
    My flashlight videos: http://www.youtube.com/playlist?list...9TIYcGeuBXa5m0

  8. #8
    Flashaholic Hoop's Avatar
    Join Date
    Dec 2011
    Location
    Spokane, WA
    Posts
    297

    Default Re: "Thor K 2012" -A Larryk14 build

    Thanks guys! Run time is about 20 minutes which is what I was aiming for. Not bad for such inexpensive batteries! I have not timed it yet though. The front of the bulb gets very hot with continuous operation but has not melted the bezel and I have left it on for maybe 10 minutes straight. When I replace the bulb some day I will add a thin silicone O-ring so that the bulb doesn't touch the bezel.

    Edit: Hmm. Perhaps I should order that O-ring now and add one in and do a continuous run time test.... Will be something like an 8" x 3/32" O-ring from McMaster.
    Last edited by Hoop; 08-13-2012 at 01:15 PM.

  9. #9
    BVH's Avatar
    Join Date
    Sep 2004
    Location
    CentCalCoast
    Posts
    6,092

    Default Re: "Thor K 2012" -A Larryk14 build

    Very nicely done! Along with all the others...Great find on the Voltage monitors! Just ordered a few. There's nothing like the 600 Watt QX lamp running at 30V! Like the cooling fan addition! Great shots!
    WWII 60" Anti Aircraft Carbon Arc (Sold), Short Arcs: 1.6KW NightSun, 1KW VSS-3A, .8KW TrakkaBeam, 600 Watt M-134 Gun Light, 500 Watt X-500-14s, 500 Watt Starburst, 300 Watt Locators, Megaray, 150 Watt Communicator, Maxabeam Gen3, LarryK14@52V

  10. #10
    Flashaholic willieschmidt's Avatar
    Join Date
    Jun 2011
    Location
    Houston
    Posts
    134

    Default Re: "Thor K 2012" -A Larryk14 build

    Kick@ss light! Great feeling to be on the finishing end? Good pics & most excellent documentation. Digital voltage is a nice touch. Regards, Willie
    Last edited by willieschmidt; 08-13-2012 at 03:06 PM.

  11. #11
    Flashaholic Hoop's Avatar
    Join Date
    Dec 2011
    Location
    Spokane, WA
    Posts
    297

    Default Re: "Thor K 2012" -A Larryk14 build

    Thanks BVH and willieschmidt!

    Yea. Feels good to have it totally finished. I was held up for a while figuring out how to tastefully do the voltage display covers. I almost went as far as to model some covers up in CAD and cnc machine them in my buddies shop. They would have had screw mounting that way and perfect alignment. I am happy with how my home brew solution looks though.
    Last edited by Hoop; 08-14-2012 at 12:28 AM.

  12. #12

    Default Re: "Thor K 2012" -A Larryk14 build

    That is just beautiful, Hoop!

    Totally love this build.
    I'm an excellent driver. Of course I don't have my underwear... I'm definitely not wearing my underwear

  13. #13
    Flashaholic*
    Join Date
    Aug 2006
    Location
    Boston, MA, USA
    Posts
    2,806

    Default Re: "Thor K 2012" -A Larryk14 build

    I saw this while I was away and never replied. I really like this. The OLED displays are awesome!

  14. #14
    Flashaholic* KuanR's Avatar
    Join Date
    Jan 2012
    Location
    Macau S.A.R.
    Posts
    1,720

    Default Re: "Thor K 2012" -A Larryk14 build

    This is amazing, especially with JimmyM's driver and the OLED displays!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •