NEW XML2 90 + HIGH CRI P60 / D26 Replacement Modules

[nailbender]

NEW XML2 90 + HIGH CRI P60 / D26 Replacement Modules

These are XML2 emitters (XMLBWT000US60Z7) 3000k 90 cri emitters, S6 flux is the highest flux available in 90CRI. As with all XML2 emitters they have pretty good throw with a adequate amount of spill.

As with most warm white emitters these look much like a incan and the color rendition is great. At S6 flux it is the highest lumen Hi CRI single emitter

As with most XML2's both smooth and op reflectors are available. The smooth gives the best throw with a distinct hotspot while the Op will yield a slightly floodier and more blended beam.

Please let me know if you are using in a Solarforce product as they can use a longer module.

NOW MOUNTING EMITTERS ON ALL COPPER DIRECT BOND SINKPADS

Available in the following levels

3 amp regulated with last mode memory. (2.8v - 6v )
These have reverse polarity protection and low voltage protection

• 1 level
• 3 level (low 5% / med 30% / hi 100%)
• 3 level (low 5% / hi / Strobe)
• 5 level (Moonlight / low 5% / med 30% /med high 40% / hi100% )

While these can be ran at higher amperage you are paying for a certain tint and rating and above 3.0 amps the tints may not be true as designed.

Also available in a 2.2 amp (3.6-16volt) One level

__________________________________________________ ________________________________________________

Price is $40 Includes free shipping in the US / free potting and 1 pc of Copper tape included in price.

International shipping is $12 for 1st class Int. and $23.95 for priority mail Int.

Paypal addy is in my Bio / please include CPF nickname and what ordered in paypal notes and below in thread.
MAKE SURE YOUR ADDRESS IS SHOWING IN PAYPAL OR INCLUDE IN NOTES

Dont forget to specify smooth or Op reflector if not listed Op will be installed.


Below is a beam shot, it is not quite that beige looking in real life but a bit more incan looking. It must have been picking up the slightly off white walls.

[nailbender]

Hi

This is a re-post of a thread started several days ago that got lost in the shuffle of the last few days. So here it is again.

Sorry I can't do anything about the posts and the previous orders shown in previous thread but be assured all previous orders have been shipped.

Thanks

Dave

[donn_]

Hi Dave,

I'll take one:

2 level (low 5% / hi)
3.1A
Smooth Reflector
Potted


Are you going to use any of these in D36 modules?

[nailbender]

Hi Dave,

I'll take one:

2 level (low 5% / hi)
3.1A
Smooth Reflector
Potted


Are you going to use any of these in D36 modules?

Hi Donn

Sure I can put these in a D36 no problem but they either have to be a 6 volt max driver or the above mentioned 2.2 amp single level 18 volt max.

Price would be $5 more / smooth or op

Thanks

Dave

[donn_]

Hi Donn

Sure I can put these in a D36 no problem but they either have to be a 6 volt max driver or the above mentioned 2.2 amp single level 18 volt max.

Price would be $5 more / smooth or op

Thanks

Dave

Cool. 6V is fine.

for one with the same spec as the one I already ordered.

2 level (low 5% / hi)
3.1A
Smooth Reflector
Potted

[ErikP]

This is huge, IMO the most desirable XM-L available. Highest 90-CRI, highest flux group, and a "whiter," slightly cooler 7A2 tint (~3200K) versus the warmer 7A1 (~3000K) tint.
ErikP for D26 drop-in: XM-L, 90-CRI, S6 flux, 7A2 tint *direct drive*, smooth reflector
(Unique Transaction ID # 69V814567H8910444)

[senna94]

Dave,

I will take a 2.8 amp regulated 3 level (low,medium,high) with last mode memory and OP reflector.

Thanks!!

[nailbender]

Cool. 6V is fine.

for one with the same spec as the one I already ordered.

2 level (low 5% / hi)
3.1A
Smooth Reflector
Potted

Hi Donn

Both of yours have shipped

Dave

[merlocka]

Dave,

I'll take 1

2.8A 2 level, SMO

Paypal incoming

[ToyTank]

Any chance you could make a mule P60 drop-in with these?

[91FromStars]

CPF: 91FromStars

90+high CRI XML P60 style
2.8 amp regulated with last mode memory. (2.8v - 6v )
3 level (low 5% / med 30% / hi)
OP reflector
Potting

[biglights]

90+high CRI XML P60
2.8 amp
3 level (low 5% / med 30% / hi)
OP reflector
Potting



I will be putting this in a LP2, but I will be using protected batteries. Thanks for your help Dave.

[DRoc]

I'll take the following:
2.8 amp regulated with last mode memory. (2.8v - 6v )
2 Mode
OP reflector
Potting
International shipping $5 for 1st class Int

Paypal incoming

[Xmldriver]

Any chance you could make a mule P60 drop-in with these?

+1 - Would this work OK in a P60 format?

[nailbender]

+1 - Would this work OK in a P60 format?

Hi

I am not sure what you all really are after, while not an expert I dont think the P60 pill will thread in a mule properly. Now if you mean can I do a module like a mule then the answer is no. To work in a P60 host there must be a reflector or something that provides the tension it takes to make a ground and positive connection.

As I said I am not quite sure what you all were asking but maybe that answered it.

Dave

[Xmldriver]

Hi

I am not sure what you all really are after, while not an expert I dont think the P60 pill will thread in a mule properly. Now if you mean can I do a module like a mule then the answer is no. To work in a P60 host there must be a reflector or something that provides the tension it takes to make a ground and positive connection.

As I said I am not quite sure what you all were asking but maybe that answered it.

Dave

Thanks Dave, great response as always :-)

For me, I'm after a 'wall of light', with no or very little hotspot and an even beam. I understand this is a challenge in the P60, hence my question. I think maybe the closest we'll get is a heavily stippled reflector? What do you think?

[ToyTank]

Thanks Dave that is exactly what I was asking. I'm not sure what they are called but I have seen P60 modules without reflector and the emitter mounted shallow for flood. Similar to some of the triples but without optics.

[Gothmog]

Hi,there!
I will take one,
2.8amp 3200k 90 cri
3 level (low 5% / med 30% / hi)
OP Reflector
potted

[ToyTank]

Dave,

I'd like 1x 90+ CRI XM-L drop-in
---------------
2.8V-6V driver
2.8A
3 Level(low/med/hi)
OP Reflector
Potted
----------

Thanks

[Croyde]

Hi Dave, my high CRI drop-ins arrived safely and as ever I am very pleased with your work. The colour rendition is very good to my eyes

[rcashel11]

Dave,

I'll take one 90+ Hi CRI Warm White CREE XML P60 style replacement module.

2.8 amp regulated with last mode memory. (2.8v - 6v )

• 3 level (low 5% / med 30% / hi)
• OP reflector
• potting

Thanks!

[Xmldriver]

Thinking of running one of these in a Fivemega 2*18650 Mag D26. I think it should handle 3.1amp with no problem, could I get any higher perhaps 3.5a or even 4.2a do you think?

[nailbender]

Thinking of running one of these in a Fivemega 2*18650 Mag D26. I think it should handle 3.1amp with no problem, could I get any higher perhaps 3.5a or even 4.2a do you think?

Hi

If you do not want the proper tint then yes it can be built for 4.2 amps but still can only be ran for shorter periods of time on high.
I am not quite sure why you would want to run a high CRI that much higher than specs but sure it can be done.
Do realize it will tint shift running that much higher amperage and I am not smart enough to know if it messes with the CRI rating but I would imagine since it will tint shift there is some corresponding deviation in CRI.

Dave

[donn_]

Hi Donn

Both of yours have shipped

Dave

Gottem today, and, as usual, they're great. The tint and beam are fantastic, and low is excellently low.

If anyone's on the fence on this emitter, don't be. It's beautiful!

[nailbender]

Gottem today, and, as usual, they're great. The tint and beam are fantastic, and low is excellently low.

If anyone's on the fence on this emitter, don't be. It's beautiful!

Hi Donn

thanks for the kind words, I knew you would like them. They are a great warm white tint, Cree keeps surprising us. I would love to see some colored XML's such as red and greens.

Have a great weekend

Dave

[senna94]

I received mine today and was not sure what to expect. I am blown away by the tint on this beauty. It renders incandescent lamps obsolete. It is like the tint on my Surefire A2. This has given new life to my SF G2 nitrolon and replaced the FM strion kit I had in there. Incandescent color rendition,3-levels of output,primary and rechargeable compatible,LED regulated efficiency and long runtime. This is a no brainer.

Please put me down for another one exactly as the first one I ordered Dave.

2.8 amp regulated 3 level (low,medium,high) with last mode memory and OP reflector.

Thanks!!

[Xmldriver]

One 90+ Hi CRI Warm White CREE XML P60 style replacement module.

3.1amp regulated with last mode memory. (2.8v - 6v )

3 level (low 5% / med 30% / hi). OP reflector. Potting and tape. Plus intl.post. 45 Paypal sent.

Thanks!
Sent from my XT320 using Tapatalk 2

[yellow]

Hi Dave,
interesting tint, so I have to get one ...
+ a spare for my existing "neutral" insert.


1 piece 90+ Hi CRI Warm White XML P60 Style insert +
1 piece XM-L T6 3C 5000 K P60 Style insert
both 2.8 A,
3 level (low-->med-->high)
last mode memory
2.8 - 6 V
potted
OP reflector


for
2*40,--for the inserts
2* 5,-- potting + tape
1* 5,-- intl. shipping (up to 2 inserts)
-------
95,-- * 1,04 for PP fees
= 98,80 sent




PS: if the XP-G2 inserts will once be offered in three level low>>med>>high, or 2 level low>>high, I might be in for one (at least)



another thing:
after having done some very prolonged accu-cell testing, I noticed the following discoloration:

I dont think there is any effect on the output or the beam.
Insert with metal tape is very tight fit into body, heat transfered to body immediately.
While having the light run, it was in front of a fan to cool it down ...
... but I am asking myself what to do, to prevent that for the new modules?
(except for not doing the cell testing any more ...)

[edit]
that poor insert is done now, as the discoloration has extended further ...
If anyone reads this, pls take my advise to not use a fan for cooling, but to submerge the light in water. That works much better. You have to get the heat generated away!
(I did this at first, but the host showed not to be waterproof)
[/edit]

[nailbender]

Hi Dave,
interesting tint, so I have to get one ...
+ a spare for my existing "neutral" insert.


1 piece 90+ Hi CRI Warm White XML P60 Style insert +
1 piece XM-L T6 3C 5000 K P60 Style insert
both 2.8 A,
3 level (low-->med-->high)
last mode memory
2.8 - 6 V
potted
OP reflector


for
2*40,--for the inserts
2* 5,-- potting + tape
1* 5,-- intl. shipping (up to 2 inserts)
-------
95,-- * 1,04 for PP fees
= 98,80 sent




PS: if the XP-G2 inserts will once be offered in three level low>>med>>high, or 2 level low>>high, I might be in for one (at least)

another thing:
after having done some very prolonged accu-cell testing, I noticed the following discoloration:



I dont think there is any effect on the output or the beam.
Insert with metal tape is very tight fit into body, heat transfered to body immediately.
While having the light run, it was in front of a fan to cool it down ...
... but I am asking myself what to do, to prevent that for the new modules?
(except for not doing the cell testing any more ...)

Hi

These are high wattage emitters and prolonged running of these emitters on high may have a detrimental effect, even with a fan running on the flashlight it is NOT like holding it in your hand. I have many many times told of the possible detrimental effects for laying a light down on high level for an extended period of time, I have always said a good rule of thumb is if it is not too hot to hold with your Bare hand then you are fine if it is uncomfortable holding it then turn it down or off. You hand still will wick heat better than moving air in my opinion.
The other down side is the light is usually sitting in one position so all the heat is wicked upwards to same point to some extent. P60's are never going to be as heat efficient as an individual host designed for heat transference and of course this is why you will seldom find a manufacturer building XML lights above 2.5 amps.

I can only do so much and then you have to monitor the heat, I use Arctic Aluminum when mounting all MCPCB's and fill all cavities with thermal epoxy after that you pretty much have to monitor the heat as there is not much more to do on my end.
I quit doing runtime tests your way when the emitters got to the high wattage they are at now. I purchased a CBAIII battery tester (now CBA IV) and while expensive with the higher wattage emitters I thought it safer.

Sorry wish I had a foolproof way to help

I believe I answered your question on the XP-G2 in that thread

Dave

[Ti²C]

Hi,

PP #34B985473S0005504 sent for one module, xm-l 90+ cri, 3.1Amps with memory, 3 levels low-mid-high, OP reflector, free potting and int'l shipment.

Thanks,