SupBeam K40 - thrower ( XM-L U2, 3x18650 ) Review

candle lamp

Flashlight Enthusiast
Joined
Jun 16, 2010
Messages
1,572
Location
South Korea
SupBeam was newly established this year is a new manufacturer on the scene. Yineng is a mother company founded in 2006 and has been dealing with ODM and OEM of various fields such as lasers, batteries, flashlights for many years.
The K40 is a high-output thrower flashlight with a XM-L U2 installed, runs on 3x18650 batteries, which I will be reviewing.

S-0.jpg


S-1.jpg


Packaging is a nice aluminum box with built-in packaging foam. Included inside is the light, user manual, warranty card, extra o-rings, tailcap rubber switch boot, lanyard, nice holster.
.
.
Manufacturer Specifications from SupBeam website & user manual :

- Cree XM-L U2 LEDs with lifespan 20yrs of runtime
- Max. 1147 lumens output (3x18650)
- Output (selected by magnetic ring) :
Level 1 : 0.5 lm (2000hrs)
Level 2 : 21 lm (140hrs)
Level 3 : 146 lm (22hrs)
Level 4 : 360 lm (9hrs)
Level 5 : 620 lm (5hrs)
Level 6 : 1147 lm (2hrs)
- Standby current : 65uA
- Strobe : 1147 lm (4hrs)
- Working voltage : 4v~13v
- Max. Runtime : 2000hrs
- Max. beam : 700meters
- Peak beam intensity : 75000cd
- Aircraft grade aluminum body structure
- Premium Type III hard anodized anti-abrasive finish
- Ultra-clear tempered glass lens with anti-reflective coating
- Momentary forward click tactical switch
- Strobe mode for tactical and emergency use
- Smooth reflector for max. light output
- Highly focus beam for maximum distance
- Tactical knurling for firm grip
- Streamlined body design
- Mechanical reversed polarity protected design
- Intelligent high efficient circuit for max performance and runtime
- Intelligent temperature controlled light output for safety
- Impact resistant 1.2meters
- Waterproof : IPX-8 Standard (2meters)
- Size 186mm x 76.2mm
- Weight 453g

* Notice : The above mentioned parameters (tested with three 2600mAh batteries) are approximate and may vary between flashlights, batteries, and environments.
.
.
S-2.jpg


S-3.jpg


S-4.jpg


The hard (type III) anodizing is black, with no chips or damage on my sample. The labels
on the body are clear, bright white gainst the background. There is a label mark on the control ring that lines up with the labels on the head. The manufacturer and model name are printed on the battery tube. The knurling is present over battery tube only.
.
.
S-5.jpg


The light has mainly 2 parts (i.e. head and battery tube) There is a battery carrier as well.
.
.
S-6.jpg


The light has a scalloped bezel ring and a waterproof o-ring between the bezel ring and reflector. There are two shallow and three deep cooling fins on the head. The head base of the light has a positive contact spring to contact with the positive contact of the battery carrier. The very wide negative contact rim surrounds the central positive contact.
.
.
S-7.jpg


The light uses a very nice AR coating lens, and the sky blue hue is reflected on it.
The very large (inner dia. 63.8mm) and deep aluminum (overall depth 51.2mm) reflector is smooth, and nicely finished. The K40 uses a XM-L U2 emitter, it's perfectly centered in the bottom of the reflector cup. I would expect excellent throwy beam.
.
.
S-8.jpg


There is a control ring, located below the cooling fins. All six constant output switching including Standby and Strobe is controlled entirely by the control ring. The light has ten slight indents on the control ring to help with feel. There is a label mark (▼) on the control ring that lines up with the labels on the head. The individual six constant output levels are not labeled on the head, but there is a graded output arrow () which shows the direction of the output levels. There are firm detents at each level, with a slight click. So you may need to count detents to figure out what output level you are set to.
The total traverse of the control ring is about 165 degrees of the light. The control ring action is not so smooth than I expected.
.
.
S-9.jpg


The light uses a metal battery carrier that holds 3x18650 cells in series. It looks sturdy and well-made. The positive contact plate is slightly raised, and the negative contact spring has good elasticity. So all types (i.e., true flat-tops, wide and small button-tops) of 18650's work fine. Longer cells may be somewhat tight, but all my protected high capacity (2600~3100mAh) cells fit. You can insert the battery carrier either orientation into the battery tube (i.e., it's reversible), because it has same ends with positive and negative connection terminals. But you should be careful to insert the 18650's into the battery carrier in the correct polarity.
.
.
S-10.jpg


I would have hoped for the fully heat-shrink tubing around the legs and the consistent tubing surface of the legs along with the length.
.
.

S-11.jpg


You can see the fully loaded battery carrier with unprotected & protected cells. I don't have any issue to insert my shortest & longest 18650 cells into the carrier. But the positive contact plate may catch on the heatshrink on the flat cells when removing them. So I need to first depress the cells towards the negative spring before removing them. Note that the cells with wider dia. will have difficulty when inserting or removing from the battery tube. The battery carrier introduces little rattle if you shake the light laterally when it's fully loaded with 18650's unprotected . But no rattle with the protected 18650 cells installed in my sample. Note that only 3x18650 li-ion cells can be used in the light (i.e., it doesn't support multiple CR123A or RCR123A due to 4~13V working voltage).
.
.
S-12.jpg


Screw threads are triangular cut, but seems good quality. Note that both male & female threads on the head & tube are anodized for head lock-out. They are smooth with no cross-threading or squeaking on my sample.
.
.
S-13.jpg


Mostly the battery tube continues the cylindrical shape with four flat, long rectangular surfaces. The diamond-shaped knurling is presented over most of the battery tube except four flat, long rectangular sides, and it's a bit aggressive on the handle, helping with grip.
.
.
S-14.jpg


The switch is the forward click switch which allows the light to be momentarily activated by half-pressing the switch while not affective the mode changing which is completely controlled by the control ring on the head. The switching travel is slightly longer than average, with average resistance and provides audible click when engaged. The switch cap sits recessed within the tail end which allows the light tail stand perfectly. There is no cut-out facilitate easily access to the switch. There are a couple of holes at the rear end for small lanyard attachment.
.
.
S-15.jpg


The tail cap is screwed to the battery tube together, and can be removed from the tube without any tools. There is dual springs (i.e., inner & outer springs) in the base. On the opposite side of the base, you will see the mechanical tail switch with a circuit. SupBeam says the electronic circuit can work by current 5A. In case of using a simple mechanical on-off switch, it can't accept 5A current. There is an o-ring at the tail threads as well.
.
.
S-16.jpg


You can attach the lanyard came with the light as shown above. I found it's easy to attach the lanyard without a split ring. The light can tailstand with the lanyard attached.
.
.
S-17.jpg


From left to right, VicLite 18650 protected, Skyray STL-V2, Niteye Eye40, SupBeam K40, Xtar S1.
.
.
S-18.jpg


The light is a good size with a right weight to manage it. The operating the control ring with two fingers (i.e., thumb and index finger) is relatively easy, but difficult with the thumb only. The gripability seems good. I find handling & balance of the light is good. Overall build quality is very high.
.
.
S-19.jpg


K40 comes with a nice nylon holster with a velcro strap on the head. The light fits in the holster head-up only.
.
.
Measured Dimensions & Weight

S-20.jpg

.
.
User Interface

On-off is controlled by the tailcap forward switch and output switching is controlled by the control ring in the head. Turn the light on-off by the tailcap clicky – press for momentary, press and release (i.e., click) for constant on.
There are six constant output levels, standby, and strobe. Change output modes by turning the control ring in the head. Arranged from left to right (with the head facing forward) in the following order. L1 (min. output) -> L2 -> L3 -> L4 -> L5 -> L6 (max. output) -> standby -> strobe.

No light is produced on standby, but a small current will be drawn to allow the circuit to respond to a ring turn as described below.
.
.
Standby Current Drain

Due to the control ring and electronic tail switch, the light has a small current when fully connected and control ring arrow is pointing at standby mode and the tailcap switch is clicked on.
I measured this current as 59.5μA with 3xVicLite 2600mAh on the head, and measured as 14.9μA on the tailcap. There is no current draw when the tailcap switch turned off as expected. Since the cells are arranged in series for 3x18650 cells, that would translate into around 4 years before the cells would be fully drained. Note this (74.4μA) is slightly higher the 65uA standby current listed in the manual, but this is quite reasonable for a standby current. If you want to break this current, store the light locked-out by loosening the head or turn the light off by the tailcap clicky when not in use.
.
.
PWM

S-21.jpg


The light shows no sign of PWM at any output levels. I think the light is actually current-controlled as claimed. I notice there is neither buzzing sound nor tint-shift at all output levels with the naked eye on my sample.
.
.
Runtime

1. Fan Cooling

S-22.jpg


Runtime performance is very good and flat regulation is evident on L6 I tested. The light settles around the 88% output mark for the runtime with cooling. I could see the light dropped down to a very low output mode similar to moonlight, instead of completely shutting off when the battery protection circuit was reached, and it flickered shortly three times every 25 seconds at a very low output for low battery warning.
The runtime for 10% output of max. output (L6) for various 18650 is as follows.
1) 3xVicLite (2600mAh) : 107 min.
2) 3xNLTEK (3000mAh) : 125 min.
3) 3xTorthGear (3100mAh) : 130 min.

* Note that the original cell of the NLTEK is LGABD11865 (3000mAh), and its maximum charging voltage is 4.35v for full capacity. But charged it 4.2v for runtime test, so the capacity is about 2700mAh reduced with about 300mAh.
.
.
2. No Cooling

S-23.jpg


I have done a comparison of fan cooling and no cooling for the light, and measured surface temperature on the no cooling run as I had done that in EYE40 review. The lack of cooling caused a small drop (4~10%) in output over the time, along with max. output (L6), but it's practically impossible for you to see the difference visually. This resulted in longer runtime. The light shows around the 78% output mark at least for the runtime with no fan cooling.
.
.
S-24.jpg


You can see the four points on the light where the thermal probes were set in pace as illustrated above for no fan cooling run.
I measured with thermal probes attached to four points of the light for the no cooling run only. The room temp. was 22.2~22.7 degrees, and window was ajar on the test room. The resting temp. for K40 was 24.8 degrees.
.
.
S-25.jpg


Note that left y-axis is the relative output. The black, cyan, green, and blue lines represent surface temperatures of the light in degrees centigrade (celsius) should be read off the right y-axis. The temperature continued to slowly rise in the course of the max. output (L6) run, reaching a max. 50 degrees at the points #1 and #3. The temp. at the point #4 (i.e., battery tube) reached a max. 48 degrees. It's almost impossible to express the graph in writing, but the light get hot (but not too hot, rather warm).
.
.
Beamshot

1. White door beamshot
- ISO100, F/3.5, 1/40sec, Auto white balance

S-26.jpg
S-27.jpg

S-28.jpg
S-29.jpg

S-30.jpg
S-31.jpg


The overall beam profile is very clean without noticeable flaws and has an intensely small hot spot. The spill beam is pretty wide and it is rather dim relative to the hot spot.
.
.
2. 55m Outdoor Beamshot
- ISO100, F/2.8, 1sec, Auto white balance

S-32.jpg

- Control Shot
.
.
S-33.jpg

- STL-V2
.
.
S-34.jpg

- K40
.
.
S-35.jpg

.
.
3. 60~65m Outdoor Beamshot
- ISO100, F/2.8, 1sec, Auto white balance

S-36.jpg

- Control Shot
.
.
S-37.jpg

- STL-V2
.
.
S-38.jpg

- K40
.
.
S-39.jpg

.
.
4. 130m Outdoor Beamshot
- ISO100, F/2.8, 1sec, Auto white balance

S-40.jpg

- Control Shot
.
.
S-41.jpg

- STL-V2
.
.
S-42.jpg

- K40
.
.

S-43.jpg

.
.
5. [Edit 12.11.05] 155m Outdoor Beamshot [Edit 12.11.05]
- ISO100, F/2.8, 1sec, Auto white balance

S-44.jpg

- Control Shot
.
.
S-45.jpg

- STL-V2
.
.
S-46.jpg

- K40
.
.
S-47.jpg

.
.
* K40 provided by SupBeam for review. (Thanks!)
.
 
Last edited:

tatasal

Flashlight Enthusiast
Joined
Jan 25, 2012
Messages
1,192
Very nice review. Good comparative beamshots. I will look forward for your succeeding reviews.
 

Bwolcott

Enlightened
Joined
Apr 19, 2012
Messages
561
Location
California
excellent pictures im loving mine, I got one od the l3 illuminations versions, he says they are driven harder but id like to see a comparison in numbers of yours vs turbobb's
 

Dubois

Enlightened
Joined
Feb 12, 2012
Messages
660
Nice review, thanks. My K40 arrived last week, and I took it out last night for a little stroll. I was pretty amazed by the output. I don't have any other throwers to compare it to, but it is seriously impressive. As you say, very good build quality, at a good price. Mind you, I was more pleased with seeing a badger run along a path about 50 meters away.:)
 

yoyoyo109

Newly Enlightened
Joined
Nov 4, 2012
Messages
9
this light looks pretty sweet! I've been searching online though and all my browser is showing me is either sunbeam products or the manufacturers website. does anyone have an MSRP on this and know where you can pick one up?
 

RBH

Newly Enlightened
Joined
Dec 15, 2008
Messages
188
I also have the l3 illuminations version, and am very happy with it. To me the most noteworthy thing about the light is the size.
 

busycokos

Banned
Joined
Jul 4, 2012
Messages
28
you can directly order from the manufacturer , they have stock at most time ,and can send you in one or two days , if you want to receive it fast , you can choose the DHL express , it will reach you in 4-5 days, if no so hurry ,you can choose China Post Register Airmail , take longer time , but the shipping cost will cheaper , I just got my one a few days ago , really impressive ,and good price.
 

phantom23

Flashlight Enthusiast
Joined
Nov 3, 2007
Messages
2,044
Wow, I have STL-V2 and K40 makes it look dim and floody. That's really impressive.
 

Dubois

Enlightened
Joined
Feb 12, 2012
Messages
660
this light looks pretty sweet! I've been searching online though and all my browser is showing me is either sunbeam products or the manufacturers website. does anyone have an MSRP on this and know where you can pick one up?

I got mine from neonlaserchina - from their product listing, look for high powered led flashlights. It costs about $100 shipped to UK, and Steven Zhang handled it - very professional and helpful.
 

cmichael

Newly Enlightened
Joined
Jan 11, 2007
Messages
181
Location
Las Vegas
Just order the K40, From Bella Chen, Hope will get it by Next Monday, She is very nice to talk to, Hope this light will keep my TN30 company.
 

candle lamp

Flashlight Enthusiast
Joined
Jun 16, 2010
Messages
1,572
Location
South Korea
Thanks for your good word and hope enjoy your light.

By the way, I've found busycokos's excellent pictures. Have a look at these.

Thanks a lot for your gorgeous photos. busycokos! :thumbsup:
 

cmichael

Newly Enlightened
Joined
Jan 11, 2007
Messages
181
Location
Las Vegas
Just got my K40, Its my best throw LED light, I'm please with that light, Thanks for Bella taking my order, Only problem is the control ring is Little gritty to turn. Maybe need to brake in or lube?

I try my TN30 and K40, The TN30 way much more flood then K40, But I like the throw on the K40 with nice usable flood. Anyone knows the actual throwing lux in the TN30 and K40 in a meter?

I like the size of the K40, Hope they have mod for the light to make it even better throw and usable flood. Now I have the king of the flood light, I need another king of the thrower :)
 

langham

Enlightened
Joined
Feb 9, 2012
Messages
441
Location
Tuscaloosa, AL
You can mod it by taking it apart and adding a diamond based thermal paste and de-doming the XML. I am not sure that I would do that though it seems like an awesome lite as is.
 

langham

Enlightened
Joined
Feb 9, 2012
Messages
441
Location
Tuscaloosa, AL
Have any of these manufacturers thought of adding thermal barriers to the portions of the light that you touch? They seem to be adding more surface area to the outside of the light for heat-sinking and some have even added cut away sections to eliminate the drop from anodized finish, but I have not seen a thermal barrier for the handle yet. They could simply make the portion near the tail the heat sink for the battery compartment and the section in the head the heat sink for the emitter/driver. This might help the batteries as well as they would most likely run cooler.
 

candle lamp

Flashlight Enthusiast
Joined
Jun 16, 2010
Messages
1,572
Location
South Korea
Have any of these manufacturers thought of adding thermal barriers to the portions of the light that you touch? They seem to be adding more surface area to the outside of the light for heat-sinking and some have even added cut away sections to eliminate the drop from anodized finish, but I have not seen a thermal barrier for the handle yet. They could simply make the portion near the tail the heat sink for the battery compartment and the section in the head the heat sink for the emitter/driver. This might help the batteries as well as they would most likely run cooler.

I haven't thought about it yet, but your idea seems good for heat dissipation. The temperature difference between head and battery tube is not much, 3~4 degrees in my test. I think it might be worth consideration by the manufacturer.
 

Oztorchfreak

Flashlight Enthusiast
Joined
Jul 29, 2010
Messages
1,317
Location
Sydney, Australia
I got mine from neonlaserchina - from their product listing, look for high powered led flashlights. It costs about $100 shipped to UK, and Steven Zhang handled it - very professional and helpful.



I have been chatting with Steven Zhang lately and I am waiting for the X40 to come into stock as it is very similar to the TN30 but it can be charged externally without removing the batteries by a plug in the tailcap near the now off-centered on/off switch.

The website blurb says it has an output on High at 3280 lumens and it uses the new U3 LEDs instead of the U2 ones.

It is worth a look at it on the Neonlaserchina website.

I was just chatting about how similar the L3 Illumination K40, the Supbeam K40 and the Thrunite TN31 all look very similar in appearance and performance.

I speculated that maybe they are all manufactured by the same company such as Supbeam.

Let me know how your K40 performs and whether you like the build etc.

I can't wait to get hold of one of the X40s but I still have a Fenix TK75 on pre-order as well because that looks really good for its shorter length but similar in many ways to the performance of my TK70 that I have had since they were released.

I also have the latest updated TM11 V3 and some Skyray Kings that perform very good for their short length but still puts out 2000 lumens.

I highly recommend the Gold looking Skyray Kings and I have bought 9 of them now for my family and friends as they cover a wider area out the front similar to the TM11 and the Skyray King and throw pretty well for this style of light.



Cheers
 
Last edited:
Top