Wuben        
Page 11 of 11 FirstFirst ... 4567891011
Results 301 to 312 of 312

Thread: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

  1. #301
    peter yetman's Avatar
    Join Date
    Mar 2014
    Location
    North Norfolk UK
    Posts
    2,898

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Nuffin"
    Last edited by peter yetman; 02-24-2018 at 12:09 PM.

  2. #302

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by peter yetman View Post
    Check your serial number by counting the groups of red flashes when the light in in programming mode. Put the serial number in here...

    http://lux-rc.com/content/serials

    This will tell you the furmware version that you have. Version 1.1 did not have the battery check, apparently, version 1.2 did
    Correct, thank you. Here are complete release notes:


    R1.0 Apr 15, 2015
    - Beta board for OR, power pulse UI (requires special
    web timing)

    R1.1 Jun 1, 2015
    - Programming timing fixed to support all screens
    - 0.7s default mode switch time, "222" factory PIN

    R1.2 Nov 17, 2015
    - The voltage tracking/state machine full redesign
    - 1S/2S voltage display
    - Bat safety switchover (up to ~50mOhms internal res)
    - Hybrid memory revision. Selection is saved after 2s
    - MOM: on/off, mode switching, three special modes and
    programming, lock, program with holding mom, FL33 RGB

    R1.2 Dec 18, 2015
    - The battery lock leak fixed

    R1.2 Dec 31, 2015
    - The PIN enter click is set to 1/2s limit

    R1.2.1 Feb 22, 2016
    - Temperature and bounce reading fixes (stepdown issue)
    - Extra low mode (signal) switching fix (decay monitor)
    - Low-battery occasional mode switchover fix
    - 1S heavy load surge detector added. Steps down to 3W
    - Access voltage meter with MOM (lock and hold)
    - Cap discharge optimization (mode switching improvement)
    - FL33 RGB indicator fix
    - 8ms temperature reading (leads to web app re-calibration)
    - Bat. fail/lock: 7-10uA leak, waits for battery swap
    - OVP: overvolt. check on start, no runtime checking

    R1.2.2 Feb 24, 2016
    - mode saving to EEPROM fixed (FL_NOTSAVED)

    R1.2.3 Mar 7, 2016
    - 481 service PIN added: on/off the standby locator

    R1.2.4 Mar 22, 2016
    - "No memory" bug fixed

    R1.2.5 Apr 27, 2016
    - Service PIN fix: use 381 to control the standby locator
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

  3. #303
    Flashaholic Stoneking's Avatar
    Join Date
    Jan 2014
    Location
    USA
    Posts
    344

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    What is 481 service PIN added: on/off the standby locator?
    4500k XPL RD BOSS • 4000k 219C BOSS Ti • 2700k HDS Rotary

  4. #304

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Stoneking View Post
    What is 481 service PIN added: on/off the standby locator?
    And how do you use it?
    #75

  5. #305

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Hi folks
    I am having trouble with the bounce option.
    I can successfully change program outputs,currently have .04,14,74 and afterburner.
    i have tweaked the bounce sensitivity from 60 to 76% but the bounce function has never worked.
    Any suggestions would be appreciated.

  6. #306

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by scintillator View Post
    Hi folks
    I am having trouble with the bounce option.
    I can successfully change program outputs,currently have .04,14,74 and afterburner.
    i have tweaked the bounce sensitivity from 60 to 76% but the bounce function has never worked.
    Any suggestions would be appreciated.
    Turn it to 100%, then work your way down until it works right. Mine is set to 89/90ish.

  7. #307

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    That did it,thank you

  8. #308
    Flashaholic
    Join Date
    Feb 2006
    Location
    Raleigh, NC
    Posts
    117

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Are the limited copper e-series heads from several years ago old e or new e?

  9. #309

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Shurock View Post
    Are the limited copper e-series heads from several years ago old e or new e?
    I'm 90% sure they are newest possible E, they even came in modern cardboard. Let me know if a photo would help.
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

  10. #310
    Flashaholic* id30209's Avatar
    Join Date
    Mar 2008
    Location
    Croatia-Europe
    Posts
    710

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Subscribed....i see i'll spend, AGAIN, more money then i should

  11. #311

    Join Date
    Jul 2012
    Location
    Kansas City
    Posts
    3,070

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    What's the status on the V5 Wasp engine upgrade offering?

  12. #312

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Grizzman View Post
    What's the status on the V5 Wasp engine upgrade offering?
    Its actually ready to go
    https://www.oveready.com/flashlight/...-led-pcb-20mm/

    but I'm waiting for a good board selection/stocks before making announcements, which could be just a few weeks
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

Page 11 of 11 FirstFirst ... 4567891011

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •