Re: Custom Order Notification Thread- II

Re: Custom Order Notification Thread- II

Hi guys,
This is the second chapter here for notification of requested orders, discussions of orders and general reference/ back up of pending requests.

In addition to sending me an E-mail, it will be helpful if you also post here of your request.

Thanks!

- Don

Re: Custom Order Notification Thread- II

E-mail sent! /ubbthreads/images/graemlins/grinser2.gif

Re: Custom Order Notification Thread- II

McE2S 10 ohm Ha-Black – with single tritium vial and EN tab added
A spare Rubber boot cap
Ship to Singapore

Re: Custom Order Notification Thread- II

E-mails responeded to in case anyone is monitering this thread. /ubbthreads/images/graemlins/nana.gif

Re: Custom Order Notification Thread- II

Don/McGizmo:

in a couple weeks (around wen xmas comes) i will be placing an order for this:

Aleph KL1 Host (HA-Nat 1x123 pak, SF CR123, HA-Nat McE2S(15 ohm) $70
Exchange Tailcap for Trim Tailcap HA-NAT - $0?

can i get that? i post now to confirm that this can be done and got for me. keep in mind that i would want it to be down under with me in under a week from order date so i can take it on my trip to Batemans Bay from january 2 thru 15 - might want to cobble together before i order? might be able to put in a deposit before i can pay full amount if that would get it here earlier...

email sent

neg

Re: Custom Order Notification Thread- II

Neg,
I responded to your E-mail. The trim tail caps are the same price and I can assemble the switch and tube in no time. Host price is $70, yes. *we* need to find you the KL1 and I can front this and mail to you ahead of time if you promise to make good on it when you can. /ubbthreads/images/graemlins/smile.gif

Re: Custom Order Notification Thread- II

Don, i promise to make good in the $ department - might i suggest shipping the completed torch around 21-23 of december? that way if it takes a week to turn up it will be fine, and a few days more makes it still ok. of course, its your call. thankyou SOOOOOOO much! see the Cheers 'N' Jeers forum!

neg

Re: Custom Order Notification Thread- II

neg,
As soon as I get the KL1, the package will head to you. You didn't need to waste band width with a cheer over this! /ubbthreads/images/graemlins/tongue.gif /ubbthreads/images/graemlins/smile.gif

Re: Custom Order Notification Thread- II

not a waste for me, i have an unlimited T1 line, but i guess its bad for CPF. meh!

ok enuff discussion, we have it sorted so happy happy joy joy

neg

Re: Custom Order Notification Thread- II

Aleph 2, 1x123, Trim tailcap, HA-Nat, Lux III, 10 ohm, NG BB 750 ordered. Email sent.

Andrew

Re: Custom Order Notification Thread- II

Don,
Hello.Can you please build for me.
Just e-mailed you my order.
Here is my order Aleph1 head and Aleph3 head.

A:Aleph 1 head with LE and tritium
-Aleph 1 HA finish
-Luxeon III
-Nexgen 750
-tritium vial mounted at base of LED lens 4
-Please send the characters Aleph 1 engraved on the head.

B:Aleph 3 head with LE
-Aleph 3 Raw Aluminum
-5W Luxeon
-BB700

Thank you.
doctorf

Re: Custom Order Notification Thread- II

Orders received and doctor, I will e-mail you later today after I get some current work out.

Re: Custom Order Notification Thread- II

Don,
Thanks for your e-mail.
I sent e-mail again.

Thank you.
doctorf

Re: Custom Order Notification Thread- II

1x123 pak HA-Dark Gray
McE2S HA-Dark Gray 30 Ohms

Email sent.

Thanks,
Bill D.

Re: Custom Order Notification Thread- II

Hello Sierra and welcome! /ubbthreads/images/graemlins/grin.gif

I responded to your E-mail.

Re: Custom Order Notification Thread- II

E-mail sent for:

Aleph 2 head
Nextgen BadBoy 750mA LE
1.5X123 Power Pack
Trim Tailcap w/ 10 ohm McE2S
Extra 15 ohm board for above
Ti Pocket clip (pending availability)

Re: Custom Order Notification Thread- II

Mike,

I'll answer here to avoid more similar requests if possible. I have no idea when I will get the clips. My thought is that once I have them, I will need to make up a jig for drilling and tapping the tailcaps. Ideally, this would be done prior to anodize but it is not necessary. I have no idea of cost or how well any "system" to drill and tap the caps will equate into labor time.

I won't take orders or try to keep track of something I can't currently build and ship. I believe you want this light complete with clip so it is a non order for now. The clips are nothing more than talk and ideas at present. I can't clone the prototype sample so they simply do not exist! Sorry. Let's try this again when I can deliver. /ubbthreads/images/graemlins/smile.gif

Re: Custom Order Notification Thread- II

No problem Don. Are you planning on selling just tailcaps with a clip installed when you do get them as an upgrade? If you can do that I'll take the light now and buy a tailcap with clip when they're ready. Otherwise I'll just sit on my hands for a while.

Re: Custom Order Notification Thread- II

Ordered by email one A2/1x123/LuxIII/NG500/black/Flattop tailcap - 15ohm.

Well, it looks black to me, but I'm color-impaired. Maybe its dark gray.


best regards

Re: Custom Order Notification Thread- II

Mike,
I will most likely offer the tailcap with clip seperately as well as in a build. I would prefer bundling it with a complete switch but I can see where some would want an extra option for the tail "shell" and not need a complete switch. I think the clip will have some good "generic" applications so it will not be limited to "installed only".

powernoodle,

I call them black too but when put up against a typical "black" HA part they aren't so black?!? /ubbthreads/images/graemlins/icon3.gif