Search results

fenix-store
  1. troelskc

    What was the last LED light you purchased and why?

    Zebralight SC52 - nice device for EDC. So small with a lot of punch when using a 16340 Li-Ion cell.
  2. troelskc

    WTS: P60 Drop in Light Engine

    Re: vinhnguyen54 D26 P60 Dropn Ins All Copper Bonded PCBs even XP-G2s, MT-G2 ;-) Hi Vinh! I'd like to try the insane 3000+ lumens direct drive MT-G2. Which affordable host would you recommend? It would probably not be a good idea to put it in my SolarForce L2P with extensor (2x18650)??
  3. troelskc

    Show your Solarforce Part II

    XP-G2 with a smooth reflector throws like a champ in a Solarforce P60 host, nice tight hotspot with a smooth transition to a wide usable spill. You should definitely get one of these. I will any day use my XP-G2 drop in from vinhnguyen54 (2.1A neutral) over any XM-L. The tint and beamprofile is...
  4. troelskc

    Are there drop-ins I should avoid

    Where did you get the 250 OTF lumens number from? Do you drive the drop in with 3.7 or 7.4v? I measured the following current at the tailcap: 3.7v - 0.33A, 7.4v - 0.63A. Do you have some numbers to compare with?
  5. troelskc

    Show your Solarforce Part II

    So a standard P60 drop in pill fits the M3 head then?
  6. troelskc

    Show your Solarforce Part II

    Nice combo you got there. How are the S9 tail cap in terms of sharpness of the SS bezel? I bought a S11 and simply hated it. Very inconvenient for the thumb and difficult to press. Did you get a special drop in made for the M3 or just the pill?
  7. troelskc

    Test/Review of Keeppower 18650 3400mAh (Black)

    Interesting. Things are not always simple ;) 39% = 3.6V @ 1A discharge
  8. troelskc

    vinhnguyen54 D26/P60 XPE-R4 & XP-G2 Drop In

    The current @ 4.2V is 2.26A. Amazing beam and tint. You know at which voltage it will start getting dimmer (direct drive)?
  9. troelskc

    vinhnguyen54 D26/P60 XPE-R4 & XP-G2 Drop In

    I should pull 2.1 A.
  10. troelskc

    Sold/Expired NEW XML2 90 + HIGH CRI P60 / D26 Replacement Modules

    Re: 90+ HIGH CRI CREE XML P60 / D26 replacement modules. Hi Dave! I just posted the 1.55A @ 3.6V as a general reply to the 2 earlier posts from ToyTank and mvyrmnd regarding the type of driver. The earlier test WAS done with a fully charged 4.2V cell. As I replied in the PM I'd like to do some...
  11. troelskc

    vinhnguyen54 D26/P60 XPE-R4 & XP-G2 Drop In

    I got 1.4A @ 3.6V. I assumes this is because the driver goes in direct drive. At which voltage will it go in to direct drive?
  12. troelskc

    Test/Review of Keeppower 18650 3400mAh (Black)

    Just got 2 fine batteries today. The came charged @ 3.64 v which is a kind of low storage voltage? Recommended is 40% which I calculates to 3.78 V.
  13. troelskc

    Sold/Expired NEW XML2 90 + HIGH CRI P60 / D26 Replacement Modules

    Re: 90+ HIGH CRI CREE XML P60 / D26 replacement modules. I just tried with a brand new 3.6 V Keeppower 18650 - I measured 1.55A @ tailcap. Nailbender could you confirm you are using a linear driver and which one and not a buck? Is it a Nanjg?
  14. troelskc

    where can I get (standard) P60 brass pills from ?

    Thanks. Cnquality had the them under this category: Torch Components > Torch Circuit
  15. troelskc

    vinhnguyen54 D26/P60 XPE-R4 & XP-G2 Drop In

    Thanks a lot! You use the same drivers for your XM-L drop-ins? I removed the S1 bridge to make it a no memory. Works fine.
  16. troelskc

    where can I get (standard) P60 brass pills from ?

    Seriously nowhere to buy this as a single part? I really need this as well.
  17. troelskc

    Sold/Expired NEW XML2 90 + HIGH CRI P60 / D26 Replacement Modules

    Re: 90+ HIGH CRI CREE XML P60 / D26 replacement modules. Just got the drop-in today. Very nice packaging and overall quality. I just got 2.1 A at the tailcap with a fully charged 18650. I ordered a 3 A. Is this because of how the driver works or is it actual only getting ~2A?
  18. troelskc

    vinhnguyen54 D26/P60 XPE-R4 & XP-G2 Drop In

    Just got the XP-G2 neutral 2.1A and it works just perfect! Tighter hotspot as expected and what a beautiful tint! Measured 2.08 A @ the tailcap using a cheap Trustfire 18650 and a discount DMM. Will try an IMR when it arrives. It should be the same with this driver? Upgraded my Solarforce L2P...
  19. troelskc

    Which RCR123

    AW is quality cells and you can discharge them at 3 C (1500 mA) with no problems. It won't explode or vent or anything - just shortens the overall life of the cell.
  20. troelskc

    vinhnguyen54 D26/P60 XML Drop In Run 7 Sale Thread ALL COPPER PCB SOLDER FILL NOW

    Just got the XP-G2 neutral 2.1A and it works just perfect! Tighter hotspot as expected and what a beautiful tint! Measured 2.08 A @ the tailcap using a cheap Trustfire 18650 and a discount DMM. Will try an IMR when it arrives. It should be the same with this driver? Upgraded my Solarforce L2P...

Latest posts

Top