Sold/Expired 1D P7 mag

[big vin]

To aquire some funds to make myself a triple P7 Mag, i need to sell my recently finished P7 cutdown Mag.

It is a digital camo mag, cutdown to 1D. The led is powered by a single protected 32600 D size Li Ion. The D cell has a rated capacity of 5000mAH.

The P7 produces a comfortable nice light. It is glued to a H22A (setapong) heatsink using arcric silver adhesive. The heatsink itself fits nice and tight in the flashlight body, and uses arctic silver 5 to ensure proper heat conducting to the body.

This is a nice little thrower, with a hotspot that has almost no artifacts. It could use an oragepeel reflector though to make it even a bit smoother.

price is 150$, i am willing to ship worldwide.
Price drop to 125$, 135$ shipped worldwide!
Last price drop to 115$, 125$ shipped worldwide!

Pics of the build (that i finished 3 days ago):

 

[big vin]

bump...

 

[Drewfus2101]

::free bump::

I don't think that I have every seen anyone put so much effort in making the top of the switch look so perfect. I usually leave some melted plastic just hanging off there. That speaks loads to your hard work done here.

I love the 1D P7 build. If I didn't already have one, I would buy this.

Is the lithium-ion D cell included? Is it the KD cell? What size wire did you use? What current readings did you get with that cell?

 

[big vin]

Thanx for the compliment!

the switch is actually sanded down using up to 1000grain wet sanding paper:naughty:
The D cell is included, and it is still on its first charge, as is the light!
It is the KD protected D cell
The thickness of the wire is 0.085 inch, or 2.15mm. I dont know the gauge number, but it is quite capable of the job.

ill take some current readings with my 5$ meter tomorrow.

 

[big vin]

It does about 3.2 amps, measured over the back of the flashlight.

so taking in mind a bit of internal resistance it should be right on the spot:twothumbs

 

[big vin]

i'll ship it worldwide for 10$, the rest of the shipping costs are on me....

 

[big vin]

I allso have a complete kit to build another one:

P7 on the H22A heatsink
KD D-cell litium
5 modes 2.8A driver

ill take a good offer on it...

 

[chitoz28]

Would you be interested in just selling the P7/H22A?

 

[camaro09]

PM sent.

 

[big vin]

Would you be interested in just selling the P7/H22A?

Not really, unless the buyer of the light would like to buy the extra D cell. Otherwise i am stuck with a battery i can not use...

The price for the extra battery would be 20$ ( KD protected cell, never used)

Vincent

 

[5.0Trunk]

Not really, unless the buyer of the light would like to buy the extra D cell. Otherwise i am stuck with a battery i can not use...

The price for the extra battery would be 20$ ( KD protected cell, never used)

Vincent

I'll take the D battery. Send me your PP info.

 

[chitoz28]

If he (5.0Trunk) takes the D, then I'll take the P7/H22A.

 

[ackbar]

I'm interested in the host.

 

[big vin]

@ chitoz: the D cell is still for sale. I could send the complete kit for a total of 60$.

@ ackbar: Do you mean the host only, without the internals? Ifso i am not intersted, i would like to sell the light in one piece. If you are interested please send me a PM.

 

[big vin]

I could throw in the extra D cell for free for the buyer of the mag...

 

[nitnapz]

pm sent

 

[bstrickler]

I may buy the D cell off you, pending if I can get the 1D Mag I'm looking at.

~Brian

 

[big vin]

Bump, and price drop for the light without the extra D cell. I am going to use that one for another project.

new price 125$

 

[big vin]

and up again...

 

[3D black mag]

Very nice and clean :twothumbs, free bump.


3D black mag