• You must be a Supporting Member to participate in the Candle Power Forums Marketplace.

    You can become a Supporting Member.

Sold/Expired 3AA, 6AA, 9AA & 12AA Fivemega battery holders

Candle Power Flashlight Forum

Help Support CPF:

Status
Not open for further replies.
Arrived today, thanks!

Sorry tnathletics2b, I think I must have got the last one!
 
The early bird gets the worm! I have been eyeing these for awhile now and I should have made the move...😳
 
Payment sent for:

1x 9AA to 3D battery holder $39
Shipping to Australia $9

Thanks!
 
:paypal: Paypal sent for:

(1) Brass G4 bi-pin socket - $18.00
(1) 9AA to 3D adapter - $39.00
(1) WA 1185 bi-pin bulb - $6.00
U.S. shipping - $6.00
Total - $69.00


Thanks!
 
tnathletics :paypal:for:
$39.00 9AA to 3D battery holder
$6.00 US Shipping
Total: $45.00

Thanks!

I forgot to add $6.00 for shipping in my original PayPal account, but sent it seperate after I realized my mistake.
 
Last edited:
The 3AA to 1D, can two of these be put into a 2D mag to keep the 3.6 volts? (Caution, Newbie here! This is probably a pretty stupid question, but I just want to verify if it will actually fit in the tube length-wise. I already ordered a 6AA to 2D for something else.)
 
Tkklemann said:
The 3AA to 1D, can two of these be put into a 2D mag to keep the 3.6 volts? (Caution, Newbie here! This is probably a pretty stupid question, but I just want to verify if it will actually fit in the tube length-wise. I already ordered a 6AA to 2D for something else.)
Click to expand...
no....
it might fit, but wont be 3,6v, to keep 3,6v in 2d you need to use 3 C cells, no adapters needed. that is if you wanna stay with nimh\nicd, or use single lithium ion cell.
 
Last edited:
alpg88 said:
no....
it might fit, but wont be 3,6v, to keep 3,6v in 2d you need to use 3 C cells, no adapters needed. that is if you wanna stay with nimh\nicd, or use single lithium ion cell.
Click to expand...

Maybe I should state for what this is to be used for, if it makes a difference; I am looking for a bettery solution for powering a SST-90 with a D2Flex board. I was hoping to power it using AA's and adapters if at all possible, but if 3C's would work, I am game for that too and use the 6AA to 2D for something else. What C's would you recommend?

I would think that his adapters in 3AA to 1D with two it would be a 3 Parallel Cells for 3.6v x 2 (Series). Maybe I just haven't had enough coffee yet this morning... 🙁
 
Tkklemann said:
The 3AA to 1D, can two of these be put into a 2D mag to keep the 3.6 volts? (Caution, Newbie here! This is probably a pretty stupid question, but I just want to verify if it will actually fit in the tube length-wise. I already ordered a 6AA to 2D for something else.)
Click to expand...

You can also use BLACK 8AA adapter for 4.8 volt or use 2 dummies for 3.6 volt, 4000mAh operation in bored out 2D M*g.
 
fivemega said:
You can also use BLACK 8AA adapter for 4.8 volt or use 2 dummies for 3.6 volt, 4000mAh operation in bored out 2D M*g.
Click to expand...

Vey nice piece in the link.. Now if you think that will work for my set up in the previous post, I will definitely take one and post in the other thread..

EDIT: My previous post was delayed due to being a newbie.. 🙂
 
Tkklemann said:
I am looking for a bettery solution for powering a SST-90 with a D2Flex board. I was hoping to power it using AA's and adapters if at all possible, but if 3C's would work, I am game for that too and use the 6AA to 2D for something else. What C's would you recommend?

I would think that his adapters in 3AA to 1D with two it would be a 3 Parallel Cells for 3.6v x 2 (Series). Maybe I just haven't had enough coffee yet this morning... 🙁
Click to expand...

6aa adapter would work just fine with sst50 and d2flex (you're good up to 24v), so would c cells, i used tenergy cells, wasn't disappointed.
there are many ways, FM adapter is most convenient, reliable, safe way imo, safe chemistry cells, low resistance, charge all at once.
 
- 9AA to 3D adapters - $39
- mineral glass lens - $3
- cammed 8.5 mm bi-focal metal reflector - $27
- G4 bi-pin brass socket - $18
- Two WA-1185 bulb = $6x2 = $12
- Priority Shipping to ConUS - $6

Total = $105

:paypal:
 
Status
Not open for further replies.

Latest posts

Back
Top