Best way to mod a Surefire for more power?
- Thread starter Brasso
- Start date
Help Support Candle Power Flashlight Forum
For a 6P to get more power the most obvious choice would be 2xRCR123A and a P90 lamp from a 9P.
For more, 2x IMR16340 and a P91 lamp for some wow factor.
You can also use a 17670 battery and a 3.7v lamp (from LumensFactory) but that doesn't increase output (maybe a little), but it does make it rechargeable. NOTE: LumensFactory lumens are measured differently to Surefire lumens, so those apparently high output numbers on the LF lamps are not a direct comparison to the Surefire P60.
All 3 battery types available here.
For more, 2x IMR16340 and a P91 lamp for some wow factor.
You can also use a 17670 battery and a 3.7v lamp (from LumensFactory) but that doesn't increase output (maybe a little), but it does make it rechargeable. NOTE: LumensFactory lumens are measured differently to Surefire lumens, so those apparently high output numbers on the LF lamps are not a direct comparison to the Surefire P60.
All 3 battery types available here.
leukos
Flashlight Enthusiast
That setup will be 400+ lumens, twisty switch only.
That is one of my favorites!
I also like the custom FM/Carley 1794 that Nite had a second run made of, that goes into the custom FM holder - but the P91 is alot easier route.
The AW 3 level soft start switch that goes into the surefire tail is a nice upgrade as well (this turns it into a "soft clicky" - it doesn't really click - but push / release moves it on & between levels - it will take the high amperage). Available from AW and on lighthound.com (it's about $50 for the switch guts).
So the factory surefire tailcap won't work with a P91 and the 16340's? Even the twisty/momentary switch? What's the runtime like with this setup? What's this FM holder?
If I decided to go this route, would 2 IMR18650's run the P91 OK?
If I decided to go this route, would 2 IMR18650's run the P91 OK?
Last edited:
Dioni
Flashlight Enthusiast
+1 on P91 with 2xIMR16340
FlashKat
Flashlight Enthusiast
Simple mod would be Lumens Factory drop ins that you would decide on.
Surefire clicky switches have always worked fine with the Surefire P91 and always will. I don't know what clicky switches you guys are referring to, or what you are talking about at all. Perhaps some cheap aftermarket clickies, like the type sold on Ebay and Dealextreme. But I don't know of anyone who has ever had trouble with a Surefire P91 and a Z48/Z49 or Z58/Z59 switch, I certainly have not.
leukos
Flashlight Enthusiast
Yeah, I guess the clickie warnings were mostly for E series clickies.
bstrickler
Enlightened
You could get a 17670 or 18650 (if you bore the light), and get this:
http://www.lighthound.com/Lumens-Fa...ssembly-for-SureFire-C-P-Z-Series_p_1016.html
I haven't bought it yet, (no money for one right now) but it should be fairly good. Once I get some more money, I'm buying one. (Don't want to use my CR123's unless its an emergency). I like rechargeable options
~Brian
http://www.lighthound.com/Lumens-Fa...ssembly-for-SureFire-C-P-Z-Series_p_1016.html
I haven't bought it yet, (no money for one right now) but it should be fairly good. Once I get some more money, I'm buying one. (Don't want to use my CR123's unless its an emergency). I like rechargeable options
~Brian
kramer5150
Flashaholic
you should be aware that run times will be very short with the 2xIMR16340 cells on a P91, like 10 minutes. Plus the voltage sag under load will prevent you form getting full output from that P91.
You should also be aware of the fire/safety hazards running a 2x Lithium cell setup at high current draw, and depleting them into cell reversal. You are basically WAY over 1C (discharge/capacity). That combined with excessive discharge into cell reversal can increase the likelihood of a fire/vent incident.
My suggestion would be to get the 6P bored for an 18650, add a solarforce 1x18650 extension and 2xIMR18650. That plants you in the ~400L+ range with longer run times.
You might also want to consider a P90 + 2xIMR18650 setup. If your goal is ~200L, the P91 is overkill at the expense of run time. Of course theres always the M60W, which will get you just over 200L With all the benefits of a warm tinted LED.... but that discussion is for the other forum.
You should also be aware of the fire/safety hazards running a 2x Lithium cell setup at high current draw, and depleting them into cell reversal. You are basically WAY over 1C (discharge/capacity). That combined with excessive discharge into cell reversal can increase the likelihood of a fire/vent incident.
My suggestion would be to get the 6P bored for an 18650, add a solarforce 1x18650 extension and 2xIMR18650. That plants you in the ~400L+ range with longer run times.
You might also want to consider a P90 + 2xIMR18650 setup. If your goal is ~200L, the P91 is overkill at the expense of run time. Of course theres always the M60W, which will get you just over 200L With all the benefits of a warm tinted LED.... but that discussion is for the other forum.
Last edited:
ICUDoc
Enlightened
I think the IMR cells are easily capable of this current draw.
Well guys what is it? I was thinking about trying this. Can I safely run a 6P w/ the P91 on 2 IMR16340 cells? I have a love/hate relationship with this forum. I love all the wonderful info but every time I get on here it cost me. Oh well i'm a flashaholic!!
Additionally, contrary to popular belief, my Z58 clicky has a lower internal resistance than a Z41 twisty. Yes it runs just fine with a P91 and IMR cells.
FlashKat
Flashlight Enthusiast
Yes you can run this safely. Just short runtime.
Well guys what is it? I was thinking about trying this. Can I safely run a 6P w/ the P91 on 2 IMR16340 cells? I have a love/hate relationship with this forum. I love all the wonderful info but every time I get on here it cost me. Oh well i'm a flashaholic!!
kramer5150
Flashaholic
Its not a matter of being capable, its more a matter of getting the most out of the P91. IMR16340 cells will sag under that much current draw (10 minutes to full discharge).
threads here...
http://www.candlepowerforums.com/vb/showthread.php?t=233057
380L OTF from 2xIMR16340
466L OTF from 2xAW17670
http://www.candlepowerforums.com/vb/showthread.php?t=229135
473 OTF from 2xIMR18650
leukos
Flashlight Enthusiast
If you go that route, be aware of the risk, some CPFers are flashing their P91's with that setup.
