Sabrewolf
Flashlight Enthusiast
I hope i won't get yelled at for this 
But i am in serious need of funds for my
2x 18650 EDC Project that i want to sell here
on Cpf for a 10-100 unit run. I need to
make about 5 of these right off the bat for
general passaround on Cpf, and prototyping.
So, That means that i need funds to send to the
machinist to get things going.
PLASMA CUTTER SOLD ! WOOHOO!!!
Tig Welder,
Miller Maxstar 150 STL
It is an Invertot-Based model with a 150amp
welding output running on a 110v/20a plug.
I have used it about 3 hours for various projects
on my car.. It comes with the Foot Pedal, and the
hand control that is nicely zip-tied to the gun
feeder hose. It comes with the stock cups and
tungsten rod sleeves. I have included extra
tungsten 1/16 electrodes too. Also comes with
Stainless consumable rods, and the stick-welding
claw too. Right now its setup for 110v/20 outlets,
but can easily be changed to a 220v outlet by just
cutting off the plug end and wiring a 220v single
phase plug to it. It has Auto-Voltage selection
for an easy upgrade to different plugs.
The gas regulator is included.. I can give you
a 1/4 full bottle of argon (80lb) for free if you
can meet me or come to the house to get it.
Ohh, it also comes in a nice rigid plastic
carry-case sorta like the plasma cutter
But i can't ship that anywhere...
Linky to the welder: http://www.millerwelds.com/products/tig/maxstar_150_stl/
I am asking $1150.00
Both were purchased between July-August last year.
The original warranty should still be intact on both
of these units.
All in all, i need some funds for my Edc project so
i can make a bunch for sale...
email: robertkmagill AT hotmail dot com
Thanks All!!
Robert M.
But i am in serious need of funds for my
2x 18650 EDC Project that i want to sell here
on Cpf for a 10-100 unit run. I need to
make about 5 of these right off the bat for
general passaround on Cpf, and prototyping.
So, That means that i need funds to send to the
machinist to get things going.
PLASMA CUTTER SOLD ! WOOHOO!!!
Tig Welder,
Miller Maxstar 150 STL
It is an Invertot-Based model with a 150amp
welding output running on a 110v/20a plug.
I have used it about 3 hours for various projects
on my car.. It comes with the Foot Pedal, and the
hand control that is nicely zip-tied to the gun
feeder hose. It comes with the stock cups and
tungsten rod sleeves. I have included extra
tungsten 1/16 electrodes too. Also comes with
Stainless consumable rods, and the stick-welding
claw too. Right now its setup for 110v/20 outlets,
but can easily be changed to a 220v outlet by just
cutting off the plug end and wiring a 220v single
phase plug to it. It has Auto-Voltage selection
for an easy upgrade to different plugs.
The gas regulator is included.. I can give you
a 1/4 full bottle of argon (80lb) for free if you
can meet me or come to the house to get it.
Ohh, it also comes in a nice rigid plastic
carry-case sorta like the plasma cutter
But i can't ship that anywhere...
Linky to the welder: http://www.millerwelds.com/products/tig/maxstar_150_stl/
I am asking $1150.00
Both were purchased between July-August last year.
The original warranty should still be intact on both
of these units.
All in all, i need some funds for my Edc project so
i can make a bunch for sale...
email: robertkmagill AT hotmail dot com
Thanks All!!
Robert M.
Last edited:
