Reflector advice for SSC P4 in old KL1 head

[foxtrot824]

I am upgrading an old KL1 head (ribbed style) to a newer SSC P4 LED and I want to upgrade from the original optics it comes with. I am looking for as much throw as possible. I currently have a smaller reflector from a Jet beam stuck in there but it's not the greatest. Advice would be greatly appreciated.

 

[maxspeeds]

I recall modders using McR20s reflectors with excellent results. Here's a thread that may interest you: http://www.candlepowerforums.com/vb/showthread.php?t=154447

and, here's another: http://www.candlepowerforums.com/vb/showthread.php?t=121944

 

[DaFABRICATA]

I'm pretty sure with the old RIBBED style, you will need an McR18s or Mcr18 reflector

I think the McR20 is too big to fit.

I might be wrong though.

Anyone know for sure?

 

[foxtrot824]

I've tried a McR20 and it was too long. I think I'll try a McR18s next. I've got BB Nexten 1000mA driver coming that should spice things us as well. Thanks for all the info.

 

[darkzero]

I'm pretty sure with the old RIBBED style, you will need an McR18s or Mcr18 reflector

I think the McR20 is too big to fit.

I might be wrong though.

Anyone know for sure?

You are correct, the older KL1s will need to use the McR-18/S. McR-20 is too big.

 

[mudman cj]

I have a KL1 with a smooth IMS20 in it. The reflector had to be trimmed both on the bottom and the top. Trimming the bottom makes it focus properly and trimming a bit more off of the top allows it to fit. I actually just sanded it by hand on some 220 grit paper. The result is a more concentrated hotspot with a more sudden transition from spot to spill compared to the McR reflectors.

 

[louie]

I use either Khatod or IMS 17 in 2 of mine. Pretty smooth pattern, but not necessarily a strong thrower. The Khatod needs no mods, but the legs on the IMS have to be trimmed. Both fit inside the lens gasket inner diameter, so they seem small, but I like the results.
I have used the Khatod20 with the P4 on another light, and I like it a lot, too, but it looks like it has to be trimmed for a KL1.

 

[carbine15]

I just found out that the L-mini reflectors fit the old style KL1 head perfectly. I suggest getting both the smooth and lop reflectors. They do need to be shimmed a slight bit. They are only $3.75 each!

 

[9x23]

Here is my favorite KL-1 mod thread by Icarus. It got me so excited that I decided I was going to mod my KL-1. I began by twisting off the lower bezel and broke the wires to the driver, then I removed the driver board and broke the "legs" off of the negative contact ring. Then, I couldn't remove the upper bezel to get to the emitter so after boiling it numerous times I finally put it in the oven at 350 degrees for a hour and melted the TIR optics and the head still wouldn't unscrew. On the positive side I didn't put a mark on that head, but then again I'm still working on it. :laughing: That Icarus makes it look so easy!

http://www.candlepowerforums.com/vb/showthread.php?t=192411

9x23

 

[darkzero]

I recently did a mod to an old ribbed KL1 using an optic. The owner wanted to keep it as stock looking as possible so I opted to use a NX-01 with a U2SVOH. The NX-01 has been long forgotten, many might have not even heard of them. I rarely use optics anymore but the NX-01 is still my favorite & I'm happy I still have some. The owner reported that the beam is very useful & was pretty happy with it.

 

[Icarus]

Here is my favorite KL-1 mod thread by Icarus. It got me so excited that I decided I was going to mod my KL-1. I began by twisting off the lower bezel and broke the wires to the driver, then I removed the driver board and broke the "legs" off of the negative contact ring. Then, I couldn't remove the upper bezel to get to the emitter so after boiling it numerous times I finally put it in the oven at 350 degrees for a hour and melted the TIR optics and the head still wouldn't unscrew. On the positive side I didn't put a mark on that head, but then again I'm still working on it. :laughing: That Icarus makes it look so easy!

http://www.candlepowerforums.com/vb/showthread.php?t=192411

9x23

:eeksign: poor old KL1 to get so tortured...
I like that you said it looked so easy... :naughty:

I'm anxious to hear how the poor guy will have to suffer next time... :sick2:

Did you consider to use a hammer already?

Sorry, but I couldn't resist...

:wave:

 

[9x23]

:eeksign: poor old KL1 to get so tortured...
I like that you said it looked so easy... :naughty:

I'm anxious to hear how the poor guy will have to suffer next time... :sick2:

Did you consider to use a hammer already?

Sorry, but I couldn't resist...

:wave:

Ha ha ha.....There was no torture involved except for my self-inflicted mental anguish at not getting the upper bezel open! :sweat: But now that someone has revived the idea of modding the KL-1, I will have to get a heat gun this weekend.............that head is comin' off soon even if I have to melt the pyrex lens! I want to at least TRY to mod it!

 

[gunga]

Ha ha ha.....There was no torture involved except for my self-inflicted mental anguish at not getting the upper bezel open! :sweat: But now that one has revived the idea of modding the KL-1, I will have to get a heat gun this weekend.............that head is comin' off soon even if I have to melt the pyrex lens! I want to at least TRY to mod it!

Ｐｙｒｅｘ ｉｓ ｈｅａｔｐｒｏｏｆ ｇｌａｓｓ， ｓｏ ｉｆ ｙｏｕ ｍｅｌｔ ｉｔ ｙｏｕ ｈａｖｅ ｓｏｍｅ ｂｉｇ ｐｒｏｂｅｍｓ．．．

:sick2: