Sold/Expired SOLD: SSC P7/Flupic LE for the Aleph Mule.

[datiLED]

SOLD

For sale is a Seoul P7/Flupic (V2.2) light engine for the Aleph Mule. The AMC Mule shown is not included in this sale.

The LE features a CSWPI P7 LED (from Amilite in Korea) and a V2.2 Flupic board pushing 1.2A on high. This should be good for approximately 300 lumens, give or take.

The interior of the can is completely filled with thermal epoxy, and I have added a ring of V10 ultra green glow epoxy around the emitter. The dome of the LED does not touch the window of the AMC Mule as seen in the pictures below.

Asking $148, shipped in the U.S. I am not looking for any trades at this time. The first "I'll take it" posted here takes preference over other communications. Insurance is optional, and up to the discretion of the buyer.

Again to be perfectly clear, the AMC Mule is not included in the sale of this LE.

 

[84Maroon]

Re: FS: SSC P7/Flupic LE for the Aleph Mule.

Looks great, nice work.

 

[donn_]

Re: FS: SSC P7/Flupic LE for the Aleph Mule.

 

[datiLED]

Re: FS: SSC P7/Flupic LE for the Aleph Mule.

That was quick. PM incoming.

 

[donn_]

Re: FS: SSC P7/Flupic LE for the Aleph Mule.



:thanks:

 

[AndyTiedye]

Re: FS: SSC P7/Flupic LE for the Aleph Mule.

4 minutes. That was fast.

 

[84Maroon]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

I see more of these coming out in the near future perhaps....:thumbsup:

 

[datiLED]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

I see more of these coming out in the near future perhaps....:thumbsup:

Perhaps. 😀

 

[easilyled]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

Is it possible to make a bi-flupic SSC P7 Aleph-LE (still of the same size)
so that burst is 2.4A?

 

[TexLite]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

I dont think the Tri-Flupic will fit in the e-can.

The Standard Flupic is .55",the Tri-Flupic is .77".

Michael

EDIT:Just saw you said bi-flupic,not tri-flupic.Sorry.

If they could both fit,there might be problems with the timing,can you imagine getting them out of sinc.

 

[Bogus1]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

Before the Tri-FLuPIC was developed we were going to use 3x FLuPICs. One of our considerations was that the boards might get out of sync. But in reality it would be easy enough to re-sync. them through normal use *unless* somehow they lost sync while setting the Menu and boards ended up in different modes. Even this wouldn't be a problem with a simplified program. I came to realize this possible problem was actually a problem waiting for an application. Hopefully some day we can unveil this product...

 

[TexLite]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

Before the Tri-FLuPIC was developed we were going to use 3x FLuPICs. One of our considerations was that the boards might get out of sync. But in reality it would be easy enough to re-sync. them through normal use *unless* somehow they lost sync while setting the Menu and boards ended up in different modes. Even this wouldn't be a problem with a simplified program. I came to realize this possible problem was actually a problem waiting for an application. Hopefully some day we can unveil this product...

Hi Eric,

That sounds very interesting,keep us posted.

Can I make a suggestion on a driver?It would be great to see a Quad-Flupic to go with the upcoming MC-E Cree.Four independant channels wired to the four chips in that emittter would allow for a great amount of Redundancy.You could lose one,two,or even three channels/chips and still have illumination with the remaining chip/channel.Awesome.

Also,the high setting(not burst)of around 700ma-750ma would match the MC-E spec,and the higher burst would probably cause no problems if used occasionally.

Thanks,
Michael

 

[donn_]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

:wow:

You've got a hot item here, Derek! :twothumbs

It arrived this afternoon, and so far, I've had it in an 18650 Mule and an RCR2 Mule. It's incredibly bright on high, shining it into an unlit boiler room. Lights up the whole room! The glo-application is so bright, it'll undoubtedly be a good bedside night light.

I look forward to taking it for a walk in the garden after dark...if I stay awake that long.🙄

Great work on this one!

 

[Ninjaz7]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

Whats the runtime on such a beast?:thinking:

 

[datiLED]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

:wow:

You've got a hot item here, Derek! :twothumbs

It arrived this afternoon, and so far, I've had it in an 18650 Mule and an RCR2 Mule. It's incredibly bright on high, shining it into an unlit boiler room. Lights up the whole room! The glo-application is so bright, it'll undoubtedly be a good bedside night light.

I look forward to taking it for a walk in the garden after dark...if I stay awake that long.🙄

Great work on this one!

Awesome! I am glad to hear that you are enjoying it. :thumbsup:

 

[84Maroon]

Re: SPF: SSC P7/Flupic LE for the Aleph Mule.

And here I thought I would never want a mule......:thinking:

 

[mejesster]

any news on more of these?

 

[datiLED]

any news on more of these?

PM sent.

 

[Ninjaz7]

any news on more of these?

+1 😱oo:

 

[wsmd]

Likewise! Please let us know, Derek.

(edited 07/16/08 0922 name correction)