vinhnguyen54 D26/P60 XPE-R4 & XP-G2 Drop In

[Skylumen]

vinhnguyen54 D26/P60 XP-E2 & XP-G2 Drop In NEUTRAL XP-G2 Available

Need an XP-E2 or XP-G2 Drop in? Order here!


$42 per drop in

Any mode or drive current you want. But below are some drivers and mode options.

Multi-Mode High Current & Low Voltage option: 2.7-4.5V max

A: Last mode memory B: No mode memory

1) LowLow, Medium, High, LowLow, Medium, High, 10Hz Strobe, 2HZ Blink, SOS, Beacon
2) High, Medium, LowLow, High, Medium, LowLow, 10Hz Strobe, 2HZ Blink, SOS, Beacon
3) High, Medium
4) High, 10hz Strobe
5) Medium, High, 2hz Blink
6) High, Medium, 2Hz Blink
7) LowLowt, Medium, High
8) High, Medium, LowLow

• LowLow 50mA so its a good usable low
• Medium = 35% power so it’s good for normal use
• High = 100% the current power you choose
• The driver Operates from 2.5-4.5V
• Under 2.8V the output will automatically reduce to 35% and blink once a minute
• 1x Li-ion or 3xNiHM only. 2*CR123 or 2*Li-ion = Poof= Dead Drive/LED

1 Mode High Voltage & Low Current : 3-18V - Regulated Single Mode pull 1.5-2.2A Not the brightest options has a big voltage range. Same brightness with 1 li-ion, 2 li-ion 3 li-ion, or 4 li-ion.

Multi-Mode High Current and Medium Voltage: 2.8-6V
- Low-Medium-High with memory
- Low-High with memory
- Low-Medium-High-SOS-Strobe with memory
- Low-High-Strobe with memory

1 Mode High Current and Medium Voltage: 2.8-6V

Solder Fill: FREE

Paypal: [email protected]

FREE SHIPPING WORLDWIDE

 

[LilKevin715]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

Typo fixed by Vinh, nothing to see here.

 

[Skylumen]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

I seem to be confused... I though there were no XRE bins past R2? Are you referring to a XPE-R4?

Just edited the mistakes.

 

[Skylumen]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

XP-G2 now available

 

[tobrien]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

how high are you able to push your g2s?

 

[Skylumen]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

how high are you able to push your g2s?

I havnt tried current higher than 2.1A. But at 2.1A it's bright!

I just modded an Armytek Predator from an R5 to the G2 and it throws so noticeably better!

 

[tstartrekdude]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

Hi, first about your 2.7-4.5 driver, is it a boost/buck or linear and how much current does it do? Also do you or anybody else you know of have some lux number for the XP-G vs XP-G2's driven the same with the same optics?

Thanks.

 

[Skylumen]

Re: vinhnguyen54 D26/P60 XRE-R4 Thrower Drop in

My driver are 7135 based drivers sold at illumination Supply. I have no lux measurement.

 

[De-Lux]

Vin,
I have a 6p that is bored for 18mm cells and want a XP-G2. What is your recommendation for peak output? I would be interested in the thre mode moon/med/high and can run either a single18650 or two 18350's. Thanks

Sent from my YP-G70 using Tapatalk 2

 

[Skylumen]

I got a low-medium-high driver that pulls about 2.1A on High and has a working voltage range of 2.5-9V. But if you are running just 18650 I strongly suggest my 2.5-4.5V driver. Its very efficient and well regulated.

Vin,
I have a 6p that is bored for 18mm cells and want a XP-G2. What is your recommendation for peak output? I would be interested in the thre mode moon/med/high and can run either a single18650 or two 18350's. Thanks

Sent from my YP-G70 using Tapatalk 2

 

[De-Lux]

Vin,
What would be the output of the 2.5-4.5v driver? Also, I am curious about the tint of the XP-G2. Thanks again.

 

[Skylumen]

Vin,
What would be the output of the 2.5-4.5v driver? Also, I am curious about the tint of the XP-G2. Thanks again.

I can set the current of the 2.5-4.5 to anything you want. 2.1A would get you max brightness with XP-G2. The tint of the XP-G2s that I have seen thus far all cool white but more on the neutral side.

 

[De-Lux]

Sounds great. I will take a 2.5-4.5v with the high set at 2.1A. moon/med/high(2.1A). I will also take the solder fill option. This would also work with a IMR 18350? Let me know what the total comes to shipped to Hawaii. Thanks again.

I can set the current of the 2.5-4.5 to anything you want. 2.1A would get you max brightness with XP-G2. The tint of the XP-G2s that I have seen thus far all cool white but more on the neutral side.

 

[Skylumen]

Sounds great. I will take a 2.5-4.5v with the high set at 2.1A. moon/med/high(2.1A). I will also take the solder fill option. This would also work with a IMR 18350? Let me know what the total comes to shipped to Hawaii. Thanks again.

Any single Li-ion 3.7V would be fine $40 please

 

[De-Lux]

Paypal sent. Thanks again

 

[Skylumen]

XP-G2 ordered in the 17th but havnt arrived yet....

https://tools.usps.com/go/TrackConfirmAction_input?origTrackNum=9400111201080150883806

 

[Skylumen]

If you are Tyler Skensrud please PM me. I got a Titainium light which I got no idea what mod to be done. Thanks!

 

[De-Lux]

Do you still need my address. I recieved your email that you needed my address but was unable to respond. Thanks again.

 

[tattoosteve99]

Vin your inbox is full

 

[Skylumen]

Do you still need my address. I recieved your email that you needed my address but was unable to respond. Thanks again.

Email me your Address.