~WANTED~ Looking for 2 Surefire Z44 bezels - Like New

Thread Starter: Kid9P

Looking for 2 of these bezels. Must be like new, no dings or scratches.

Just need the 2 bezels, not looking to buy complete lights.

Last Post By: Kid9P Today, 09:19 AM

Looking for lowest lumen incandescent lamp assembly for surefire e1e

Thread Starter: tony212

Lumens Factory carries the HO-E1A 3v 40 lumen lamp assembly for the surefire e1e but it is too bright for my use. Need a lamp assembly that has an incandescent

Last Post By: archimedes Today, 10:48 AM

Musings on Triple emitter lights for EDC.

Thread Starter: scout24

I went down memory lane last night texting to a dear friend I met here on CPF right after I signed up. Join me if you will. Triples for the masses. Single

Last Post By: idleprocess Today, 04:15 PM

B@rt's tritium thread continued

Thread Starter: B@rt

This is a continuation of the previous thread located here

The title says it all: Tritium!



Relative brightness

Last Post By: B@rt Today, 02:30 AM

Charger with auto current selection or manual current setting ?

Thread Starter: XTAR Light

Take simple operation into account firstly, guess some of you may choose the charger with auto current selection. Just upon your inserting the battery,

Last Post By: TILL-22 Today, 01:50 PM

RB Stalker with a machined edge on the Rope

Thread Starter: old4570

Right off the Whetstone Knife Sharpener / grinder .
No stropping / de burring .
Whetstone is apparently 220 grit ..

Last Post By: old4570 Yesterday, 11:19 PM

Lumintop problem

Thread Starter: 59ride

Hi
I recently purchased a Lumintop EDC18 light. It came this week with a 18350 tube that i ordered with it. I have tried using protected cells but

Last Post By: 59ride Today, 02:30 PM

Razor Blades Stalker on the whetstone knife sharpener

Thread Starter: old4570

A video of my sharpening the Razor Blades Stalker . ( Might be of interest ? )

Last Post By: old4570 Yesterday, 07:39 PM

Fireflies E12R, NOV-MU, T9R, T1R prototype test results

Thread Starter: SKV89

I preordered in December last year and received them for over a month already but have been too busy to test and post results until now. I've been using

Last Post By: SKV89 Yesterday, 09:23 PM

Cheers to Malkoff!

Thread Starter: :)>

Unrivaled customer service and bombproof, high performing lights is a hard combination to beat!

Last Post By: adamlau Today, 04:10 PM

Cheers to Modernflame

Thread Starter: :)>

Their unprovoked act of kindness was a blessing to me and I am grateful❤️

Last Post By: xxo Today, 11:50 AM

Putco recalls bulb-shaped LED toys

Thread Starter: Alaric Darconville

Putco ("Where the putz goes") is recalling 31,716 of their bulb-shaped toys.

See here (consumeraffairs.com) and here (NHTSA.gov)

Last Post By: SubLGT Yesterday, 06:03 PM

Car battery shortage = shortage for flashaholics?

Thread Starter: markr6

There's a ton of talk lately from analysts about a potential huge li-ion shortage based on the electric car industry ramping up. GM is looking at building

Last Post By: Scotty321 Yesterday, 04:42 PM

SBT90.2 Mag 2D Mod

Thread Starter: firstlordofthefire

Hallo Together,

several years ago I successfully modded a 6D Mag with an SST90.

With the leftovers of this built I now

Last Post By: firstlordofthefire Yesterday, 11:32 AM

Recommendation For UI

Thread Starter: :)>

HDS lights really are spectacular on nearly every level. I do, however, have a recommendation that I hope is helpful and possible. I always wished I could

Last Post By: jon_slider Today, 10:12 AM