I couldn’t find a better place to post this and it’s a bit of an odd request for this forum but here goes:
I have a stream light trl1hl
Coast is having a sale, a lot of the lower dollar flashlights are sold out but I picked up a 400R to play with.
I liked that it could serve
This is what it says it is.
https://i.imgur.com/u38mhgl.jpg
I have an iFixit infrared thermometer, and Bosch wire and pipe detector, both works with 9V batteries.
I only use them 2-3x times a year,
For Sale Veleno Designs Avant Ti in mint condition, never carried shelf queen.
Description from Veleno Designs website:
-6/4 Titanium
Anyone have the old 75 lumen vision headlamp? The housing was grey in color. I should have bought 10 of them back when they were made.
I have a couple of Soehnle kitchen scale, they function with 3 or 2 AAA batteries.
They need very little power, when I measure something
I have two Malkoff MD2s for sale. They have the high/low switch installed and the current high cri M61W. I’d like $125 shipped each. Both are basically
Last Post By: soldonsurefire Today, 05:17 PMtried to look up a light and got redirected to some lightbulb dealer.
and no malware here.
I need an introduction to LED set up , electronics and troubleshooting.
I am a self taught electronics amateur and need to get more sytematic/formal.
My review of the upcoming Sofirn TF84 tactical flashlight, with 3 switches, dual UI, 18650 battery, remote pressure switch, type-C charging and 90CRI
Last Post By: KG_Tuning Yesterday, 09:20 AMI was behind a new Rav4 today (it's the newest generation Rav4, so either brand new or almost new), and the brake lights are just a single LED on each
Last Post By: Alaric Darconville Today, 05:55 PMYour talking about the plastic spacer that goes behind the clip correct?
thermal guy Today, 06:36 PMI've tried but the prongs have physically reached the end of the cutout, I can see that it is fully inserted. It looks like the clip isn't for this flashlight
NYCT Today, 06:24 PMI don't think you can get a belt clip for that
PhotonWrangler Today, 06:05 PMCan you push that insert down any further? I have several C2’s. All my heads fit flush.just tap the clip down with something. It should go all the way
thermal guy Today, 06:01 PMIt's funny that you said that. I had a post all typed up and it had that in it. Then I tried to submit and got an error and the message was gone. So I
Mgizler Today, 05:59 PMIt's "kinda the whole point" that regulated motor vehicle lighting is made to conform to the regulations.
The industry should
Hi, I have just acquired an old Surefire C2 and the pocket clip prevents the head from screwing on fully. I have compared the pocket clip to one from
NYCT Today, 05:39 PMBut...you SAW it, right? I mean that is kinda the whole point. The stop light was clearly visible. I've seen them as well and I can say that the turn
lightfooted Today, 05:24 PMNo worries brother and thank you for the additional pictures and respectful response .
soldonsurefire Today, 05:17 PMWhen members would like a comment,that adds nothing to the discussion at hand,we know on whom we can count.
soldonsurefire Today, 05:15 PMAnyone think another run of Ti VME heads would be a good idea?
thermal guy Today, 05:07 PMMy comment about a bag was mainly to avoid shorting the terminals together, a problem only 9v batteries have. Otherwise, you see to use the devices often
turbodog Today, 04:48 PMEneloop Pros last only 2-3 good years before internal resistance rises to the point that they are difficult to charge and self discharge at an even more
ChrisGarrett Today, 04:20 PMIf I cut it to the same length as a cr123a and leave the second battery in there will it still power on the light?
J_C_S Today, 03:57 PMInterested , but is this still a standard 20mm pcb ?
oldeng95 Today, 03:55 PM
Surefire C2 pocket clip does not fit correctly
Thread Starter: NYCTHi, I have just acquired an old Surefire C2 and the pocket clip prevents the head from screwing on fully. I have compared the pocket clip to one from
Last Post By: NYCT Today, 06:24 PM