So, I just dented the button top on a Sanyo NCR 18650GA when I dropped my flashlight. I am discarding the dented battery. On my new, non-dented batteries,
Last Post By: LRJ88 Today, 10:16 AMJust got a Wurkkos WK30. The standard battery is a 26650 but the light can take 21700s and 18650s.
I want to buy extra batteries but am
Hi, I have just acquired an old Surefire C2 and the pocket clip prevents the head from screwing on fully. I have compared the pocket clip to one from
Last Post By: NYCT Yesterday, 07:51 PMI couldn’t find a better place to post this and it’s a bit of an odd request for this forum but here goes:
I have a stream light trl1hl
Coast is having a sale, a lot of the lower dollar flashlights are sold out but I picked up a 400R to play with.
I liked that it could serve
This is what it says it is.
https://i.imgur.com/u38mhgl.jpg
I have an iFixit infrared thermometer, and Bosch wire and pipe detector, both works with 9V batteries.
I only use them 2-3x times a year,
For Sale Veleno Designs Avant Ti in mint condition, never carried shelf queen.
Description from Veleno Designs website:
-6/4 Titanium
Anyone have the old 75 lumen vision headlamp? The housing was grey in color. I should have bought 10 of them back when they were made.
I have a couple of Soehnle kitchen scale, they function with 3 or 2 AAA batteries.
They need very little power, when I measure something
I have two Malkoff MD2s for sale. They have the high/low switch installed and the current high cri M61W. I’d like $125 shipped each. Both are basically
Last Post By: archimedes Yesterday, 07:56 PMtried to look up a light and got redirected to some lightbulb dealer.
and no malware here.
I need an introduction to LED set up , electronics and troubleshooting.
I am a self taught electronics amateur and need to get more sytematic/formal.
Question for RRT01 owners. Is the latest iteration able to provide some form of regulation at the lower levels aside from Max?
Sent from
How are the button tops attached, as an integral part of the battery or spot-welded onto the positive contact?
LRJ88 Today, 10:16 AMany of you al recall checking a ford ecm with a papper clip and a volt meter?
raggie33 Today, 09:54 AMDang
Those Vin modded lights in copper and titanium are really nice!!!
Looks like I'm going to be spending more money in the near future.
Wurkkos WK30 rated at 90.
Very nice full flood beam with no artifacts or weird purple, yellow or green "highlights"
Uses a 26650,
Yes, exploding is a serious hazard so that would have been a HUGE mistake on my part.
I dented the battery on my second use so it seems
No problem, I hate to see a perfectly serviceable cell go to waste. Plus it would really suck if something did happen and the cell exploded because it
ferthur Today, 08:55 AMThanks for this information. I appreciate it.
ZebraCraig Today, 08:53 AMWarrior Mini’s with 219B
Sent from Tapatalk
Hi there!
2. MJP Extreme Micro. This light is not much bigger than the CR2 battery that powers it. L-M-H plus blinky
Write a PM to specacuda or to The Fraz, and they will get you on the list for the next batch. My Tiny Nugget 18650 measures 4 1/4 inches in length, with
troutpool Today, 08:41 AMA dented positive end on a GA is fine, it won't hurt its performance or safety. Filling the void with epoxy WILL cause problems because it will prevent
ferthur Today, 08:33 AMThanks in large part to this thread I've received some new LF parts this morning. I've had some Lumens Factory TailCap internals and lamps before but
Tempest UK Today, 08:25 AM
Mahi head with Osram
Thread Starter: daffyTook it out again last 2 nights while doing the bike/dog trailer routine i do every night.
Last Post By: daffy Today, 08:11 AMSuch a throwy little light that barely gets warm.