Sold/Expired SOLD: 6/4 Titanium bezel ring for A1 head.

TranquillityBase · Aug 12, 2006

I have two more, ready to ship.

$50, shipping is included.

"I'll take it" followed by a PM to me, for my link.

Thanks for looking,

TB

tino_ale · Aug 12, 2006

Re: FS: 6/4 Titanium bezel ring for A1 head.

I'll take it!

edit : PM sent!

criollo · Aug 12, 2006

Re: FS: 6/4 Titanium bezel ring for A1 head.

oops!!! missed by a minute :ohgeez:

2nd in line :grin2:

TranquillityBase · Aug 12, 2006

Re: FS: 6/4 Titanium bezel ring for A1 head.

I have you both covered...PM's sent.

TB

tino_ale · Aug 12, 2006

Paypal sent, the bezel is sold! :nana:

criollo · Aug 12, 2006

TB,

That's very nice of you !

Paypal on the way.....

Cheers

tino_ale · Aug 12, 2006

Wow, looks like a second ring has been offered!

Congrats criollo! We finally both made it :sold:

TranquillityBase · Aug 12, 2006

tino_ale said:
Wow, looks like a second ring has been offered!

Congrats criollo! We finally both made it

I can't let my friend C.T. down...

TB

criollo · Aug 12, 2006

tino_ale, i believe you beat me by less than 60 sec. Glad we both got it !!! :buddies:

TB, Paypal sent ....many :thanks: As always.....you a good man :rock:

criollo · Aug 12, 2006

criollo · Aug 12, 2006

Sorry guys, wireless network connection is slow tonight......:thinking:

Triple post

WAVE_PARTICLE · Aug 12, 2006

Third in line? :candle:

WP

Fringe · Aug 12, 2006

Man,
These are nice and would looks to sit nice and flush on your ti heads. Good work. Love to have one!

TranquillityBase · Aug 12, 2006

Fringe said:
Man,
These are nice and would looks to sit nice and flush on your ti heads. Good work. Love to have one!

The rings do screw down flush, but that is without the window and the reflector. I make an undercut at the end of the threads, so they will screw down, but there should be a gap, when everything is together. I'll post a photo of mine, showing proper gaps, in a little while.

TB

Fringe · Aug 12, 2006

Makes me feel better that mine is gapping then. Why should there be this gap?

TranquillityBase · Aug 12, 2006

Fringe said:
Makes me feel better that mine is gapping then. Why should there be this gap?

I just leaves too little room for error. The cell tube face must contact the E-can, and the bezel needs to hold the window tight. You could lap the bezel down to close the gap, but I wouldn't alter the length of the cell tube.

TB

TranquillityBase · Aug 12, 2006

The gap is uniform on both sides, i.e., cell tube to head, and bezel ring to the head. You could lap the bezel ring down, but don't take too much and make sure you remove an even amount of material so it places uniform pressure on the window. I think it looks better with a uniform gap at both ends...

tino_ale · Aug 12, 2006

That makes sense to me. You have to be sure that what locks the bezel ring tight is the pressure it applies on the wondows, nothing else. I also think the small gap is better looking than no gap at all, but that's personnal taste...

TB, are you planning to duplicate aleph parts in titanium like morelite does? :rock:

TranquillityBase · Aug 23, 2006

WAVE_PARTICLE said:
Third in line? :candle:

WP

I have two more, ready to ship.

One is yours WP, if you still want it?

TB

karlthev · Aug 23, 2006

Re: FS: 6/4 Titanium bezel ring for A1 head.

TB, I'll take one!!! Check to you tomorrow. Check your PM.

Karl

You must be a Supporting Member to participate in the Candle Power Forums Marketplace.

Sold/Expired SOLD: 6/4 Titanium bezel ring for A1 head.

Flashlight Enthusiast

Flashlight Enthusiast

Enlightened

Flashlight Enthusiast

Flashlight Enthusiast

Enlightened

Flashlight Enthusiast

Flashlight Enthusiast

Enlightened

Enlightened

Enlightened

Flashlight Enthusiast

Enlightened

Flashlight Enthusiast

Enlightened

Flashlight Enthusiast

Flashlight Enthusiast

Flashlight Enthusiast

Flashlight Enthusiast

Flashlight Enthusiast

Similar threads