HDS Systems        
Page 1 of 4 1234 LastLast
Results 1 to 30 of 117

Thread: Dual Bored 2P 18650 M*g 1.25D

  1. #1

    Default Dual Bored 2P 18650 M*g 1.25D & 2S/2P 2.5D

    (AVAILABLE)

    Please allow 7 days to ship


    Please note: I will not send email or PM to individuals regarding payment confirmation and shipping status.
    All these information will be next to your CPF handle in this post.
    All 50 States shipping will come with tracking number but for international orders I will provide label number. Sorry, no tracking available for international orders.






    Please read completly and carefully before you pay

    Here is another creation from Fivemega. 3.7 volt, 5800mAh 1.25 M*g or 7.4 volt, 5800mAh 2.5 M*g
    As you see in picture, these M*gs are shortened, rethreaded and dual bored to accept two 18650 batteries side by side and connected in PARALLEL. Using pair of AW's new 18650 cells you will get 6800mAh capacity at 3.7 volt. Excellent for P7 or SSt-50/90
    Using 2 pairs of AW's new 18650 cells you will get 6800mAh capacity at 7.4 volt in 2.5D host.
    Excellent for long run incands.
    Outside body is partially grooved only where body has enough thickness and untouched where is bored out to fit batteries. This will prevent body weakening.
    Heads are also very fine finned and flutted to manage unwanted heat.
    Battery holder is integrated with switch and comes with flashlight. No external battery holder required.
    Please make sure both batteries are inserted positive to switch side. Battries not included.
    Side of body has charging port to recharge batteries without removing from flashlight and NO balancing required for 2P version. I will also include male charging jack and rubber plug to seal when is not used.
    Any charger for 3.7V Li-ion such as this can be used for 2P version and obviously for 2S/2P version you will need this. Please balance charge all 4 cells after few pack charge.
    Switch tower is machinned off and ready to install any LED module and controller.
    Advantage of parallel cells are not only to save some space and double the capacity but less load per cell, less voltage drop, longer battery life, longer run time and higher current capability.
    All you need to do is solder pair of wire (positive and negative) to switch and connect to controller and/or LED module.
    When you hold the flashlight body horizontally, switch button is at 12:00 O'clock, one bore is at 3:00 O'clock, second bore is at 9:00 O'clock and charging port is at 6:00 O'clock.
    2S/2P (with switch tower without jack) version is excellent choice for long run ROP High or 5761 (WO tower, with G6.35 socket)
    This package will cost you way over what you can get here. Check it out.
    Host $22
    Cut, rethread $30
    Dual bored $25
    Outside grooves $30
    Head finned/flutted $40
    Switch tower cut off $15
    Battery holder $30
    Charging port $30
    Total $222

    ---
    While I charge only:
    Host $22
    Cut, rethread $10
    Dual bored $10
    Outside grooves $10
    Head finned/flutted $10
    Switch tower cut off $5
    Battery holder $20
    Charging port $10
    Total $97
    You will never find this kind of prices elsewhere.
    Package Sale Price: $97
    $8 shipping to States (Priority) for first one then add $6 for each additional.
    $16 shipping to international (first class) for first one then add $8 for each additional.
    For ducumentation purpose, it is necessary to post your CPF handle and detail of your order here and paypal note.
    Without above information, I will never figure out what the payment is for and from whom.
    Paypal: fivemega@aol.com
    Please PM me for other type of payment.
    For ducumentation purpose, it is necessary to post your CPF handle and detail of your order here and paypal note.
    Without above information, I will never figure out what the payment is for and from whom.
    Example: NewGee for:
    #98 Red 1.25D M*g $97
    Shipping to States $8
    --------------------
    2P 18650

    #01 Black 1.25D M*g $97 stub paid shipped 0309114000004628XXXX
    #02 Black 1.25D M*g $97 Drywolf paid shipped 23080440000026159505
    #03 Black 1.25D M*g $97 choppers paid shipped 03080730000166823270
    #04 Black 1.25D M*g $97 UberLumens paid shipped 23082180000028880556
    #05 Black 1.25D M*g $97 steffleu paid shipped LC547811005US
    #06 Black 1.25D M*g $97 nailbender paid shipped 03092880000110388098
    #07 Black 1.25D M*g $97 PhotonAddict paid shipped LC548067169US
    #08 Black 1.25D M*g $97 Weld Inspector paid shipped 9505513808427191048567
    #09 Black 1.25D M*g $97 n_den payment received shipped 9505513808437285099832
    #10 Black 1.25D M*g $97 n_den payment received shipped 9505513808437285099832
    #11 Black 1.25D M*g $97 jayrob paid shipped 9505513808438163151857

    ---------------------

    ---------------------
    #01 Red 1.25D M*g $97 pom70 paid shipped LC845286089US
    #02 Red 1.25D M*g $97 nailbender paid shipped 0309114000004634XXXX
    #03 Red 1.25D M*g $97 Drywolf paid shipped 2308218000002886XXXX
    #04 Red 1.25D M*g $97 nickg paid shipped LC845286628US
    #05 Red 1.25D M*g $97 CKOD paid shipped 03092880000110413738
    #06 Red 1.25D M*g $97 nailbender paid shipped 03092880000110388098
    #07 Red 1.25D M*g $97 Scharrlatan paid shipped LC548067040
    #08 Red 1.25D M*g $97 X_Marine paid shipped 23082180000028854083
    #09 Red 1.25D M*g $97 X_Marine paid shipped 23082180000028854083


    ---------------------

    ---------------------
    #01 Blue 1.25D M*g $97 3rdrock paid shipped 0309114000004627XXXX
    #02 Blue 1.25D M*g $97 Drywolf paid shipped 2308044000002615XXXX
    #03 Blue 1.25D M*g $97 Gino paid shipped 0308073000016681XXXX
    #04 Blue 1.25D M*g $97 flashfiend paid shipped 03092880000110435228
    #05 Blue 1.25D M*g $97 Jay T paid shipped 03092880000110446538
    #06 Blue 1.25D M*g $97 sbelyo paid shipped 03080730000166837161

    ---------------------
    #01 Pewter 1.25D M*g $97 nailbender paid shipped 2308044000002617XXXX
    #02 Pewter 1.25D M*g $97 nailbender paid shipped 2308044000002617XXXX
    #03 Pewter 1.25D M*g $97 pom70 paid shipped LC845286013US
    #04 Pewter 1.25D M*g $97 LightJunk paid shipped LC845286044US
    #05 Pewter 1.25D M*g $97 n_den paid shipped 2308044000002615XXXX
    #06 Pewter 1.25D M*g $97 n_den paid shipped 2308044000002615XXXX
    #07 Pewter 1.25D M*g $97 erlon paid shipped 2308218000002886XXXX
    #08 Pewter 1.25D M*g $97 nailbender paid shipped 2308218000002886XXXX

    ================
    2S/2P 18650
    ================
    #01 Black 2.5D M*g $97 FlaCracker paid shipped 03101230000057516172

    --------------------
    #01 Black 2.5D M*g (NO HEAD) $67 Rommul paid shipped 03112550000058020996
    #02 Black 2.5D M*g (NO HEAD) $67 (AVAILABLE)
    #03 Black 2.5D M*g (NO HEAD) $67 (AVAILABLE)
    --------------------
    #01 Red 2.5D M*g $97 Luke-299 paid shipped LC547920172US
    #02 Red 2.5D M*g $97 (AVAILABLE)
    --------------------
    #01 Red 2.5D M*g (NO HEAD) $67 (AVAILABLE)
    #02 Red 2.5D M*g (NO HEAD) $67 (AVAILABLE)
    #03 Red 2.5D M*g (NO HEAD) $67 (AVAILABLE)
    --------------------
    #01 Blue 2.5D M*g $97 J3004 paid shipped LC138287972US
    --------------------
    #01 Pewter 2.5D M*g $97 nailbender paid shipped 0309288000011043XXXX
    #02 Pewter 2.5D M*g $97 Colonel Sanders paid shipped
    #03 Pewter 2.5D M*g $97 spencer paid shipped LC740355964US

    ===============
    2S/2P 18650 With Swith Tower Without Jack
    ===============
    #01 Black 2.5D M*g $97 (W/S Tower WO Jack) 325addict paid shipped LC138287884US
    #02 Black 2.5D M*g $97 (W/S Tower WO Jack) 357mag1 paid shipped

    ---------------------
    #01 Red 2.5D M*g $97 (W/S Tower WO Jack) 357mag1 paid shipped 23082180000028872360
    #02 Red 2.5D M*g $97 (W/S Tower WO Jack) 357mag1 paid shipped
    #03 Red 2.5D M*g $97 (W/S Tower WO Jack) monkeyboy paid shipped LC548067005US

    ---------------------
    #01 Blue 2.5D M*g $97 (W/S Tower WO Jack) 357mag1 paid shipped 23082180000028872360
    #02 Blue 2.5D M*g $97 (W/S Tower WO Jack) CKOD paid shipped
    #03 Blue 2.5D M*g $97 (W/S Tower WO Jack) gVp paid shipped LC458383865US

    ---------------------
    #01 Pewter 2.5D M*g $97 (W/S Tower WO Jack) Steve in SoCal paid shipped 03101230000057505701
    #02 Pewter 2.5D M*g $97 (W/S Tower WO Jack) Scott B paid shipped 23082180000028848938
    #03 Pewter 2.5D M*g $97 (W/S Tower WO Jack) double0thirteen paid shipped

    ---------------------
    #01 HA matte grey 2.5D M*g $107 (W/S Tower WO Jack) (AVAILABLE)
    ---------------------
    #01 Gold Plated 2.5D M*g $137 (W/S Tower WO Jack) UberLumens paid shipped 23082180000028880556
    ---------------------
    Please find link of my other products here and click on each link you are interested on.
    ---------------------
    (A V A I L A B L E)
    Last edited by fivemega; 05-18-2019 at 09:08 PM.

  2. #2

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Quote Originally Posted by xcel730 View Post
    These look very nice. I may be in for one if you or someone could point me to what drop ins I could use. Links would be helpful. Thanks.
    Quote Originally Posted by fivemega View Post
    Switch tower is machinned off and ready to install any LED module and controller.
    --------------------------
    Quote Originally Posted by ElectronGuru View Post
    This would make a fun ROP host.
    Quote Originally Posted by fivemega View Post
    Using AW's new 18650 cells you will get 6800 mAh capacity at 3.7 volt in 1.25D and 6800mAh at 7.4 volt in 2.5D.
    --------------------------
    Quote Originally Posted by Joe_torch View Post
    Does it mean that this host is for LED only?
    LEDs work better with 3.7 volt.
    -------------------------
    Quote Originally Posted by Sgt. LED View Post
    This comes with a plastic lens and reflector correct?
    That's correct.
    --------------------

    Quote Originally Posted by Sgt. LED View Post
    I'll have to upgrade that.
    It's your option.
    ------------------------
    Quote Originally Posted by LightJunk View Post
    Can the LiteMania charger be used?
    Quote Originally Posted by fivemega View Post
    Using pair of AW's new 18650 cells you will get 6800mAh capacity at 3.7 volt.

    That charger will work if you cut the output wires and connect to supplied jack.
    Keep in mind when charging current is about 1.2 Amps, charging time will be about 6 hours if batteries are depleted.

    -----------------------
    Quote Originally Posted by ANDREAS FERRARI View Post
    Being that the cells are parallel you will not have enough volts to power a ROP.Not to mention that it has no switch tower.
    2P/2S 18650 versions can be used for ROP
    -----------------------
    Quote Originally Posted by Linger View Post
    My question is how much space is for drivers / heatsink. I presume standard such as britelumens or LITEmania's or mac's are expected, please confirm heatsink compatability.
    There are more than enough room for any heat sink ever made for M*g D
    Another word, front of C clamp (switch stopper) is completly empty.

    -----------------------
    Quote Originally Posted by Linger View Post
    No it's good, 4xAW IMR 16340, 2s2p.
    It's wasting space for 2S/2P 16340. Why not using 2S/2P 18350?
    IMR 18350 will work much better with more current capability and more capacity.

    -----------------------
    Quote Originally Posted by Linger View Post
    (Further, for 2s18650 you could remove the switch, split the top contacts and create a + and -'ve, reverse one of the cells and isolate tail-spring from the case. Maybe modding the tail contacts you could fit in 2s2p18500's...
    2S/2P 18500 won't fit. Part of batteries are in deep bored out body and can't go inside tail cap. Also double bored area is up to bottom of switch and batteries won't go further.
    -----------------------
    Quote Originally Posted by Techjunkie View Post
    Is there a battery negative contact component not pictured?
    That's true. It's not shown in the picture but comes with flashlight.
    -----------------------
    Quote Originally Posted by MunkyNutz View Post
    I'd like a 5 cell cut with body grooves and the head finned and fluted. I realize this is probably one you don't have - I could send one via Amazon, and PayPal for the service.... still $28.00 with shipping to USA 69101?
    This thread is not for service and I don't do modification service in small quantity.
    All flashlights on post one are already completed in group and quantity to reduce total cost.
    Custom service for one flashlight the way you want (if somebody can do for you) will cost way more expensive.

    -----------------------
    Last edited by fivemega; 07-06-2017 at 01:21 AM.

  3. #3
    Flashaholic* xcel730's Avatar
    Join Date
    Mar 2008
    Location
    NY
    Posts
    1,756

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    These look very nice. I may be in for one if you or someone could point me to what drop ins I could use. Links would be helpful. Thanks.

  4. #4
    Flashaholic* QtrHorse's Avatar
    Join Date
    May 2008
    Location
    Texas
    Posts
    1,159

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    As FM stated, these would be great for a SST50 or 90 build. The host should also work with Malkoff's new XPG drop-in that has a max of 5.5V rating.

  5. #5

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Does it mean that this host is for LED only?
    Thanks!
    Joe

  6. #6

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    This would make a fun ROP host

    Edit: cancel that!
    Last edited by ElectronGuru; 10-22-2009 at 06:55 AM.
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

  7. #7
    *Flashaholic* Sgt. LED's Avatar
    Join Date
    Sep 2007
    Location
    Chesapeake, Ohio
    Posts
    7,486

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    This comes with a plastic lens and reflector correct?

    I'll have to upgrade that.

  8. #8
    Flashaholic*
    Join Date
    Mar 2008
    Location
    Borneo
    Posts
    750

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Wow...as usual great looking stuff you've made there.

    Can you post the pewter color mag? I may be interested in one.

    Can the LiteMania charger be used?

  9. #9
    Flashaholic* ANDREAS FERRARI's Avatar
    Join Date
    Aug 2008
    Location
    The Great White North
    Posts
    1,040

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Quote Originally Posted by ElectronGuru View Post
    This would make a fun ROP host.
    Quote Originally Posted by fivemega View Post
    .....dual bored to accept two 18650 batteries side by side and connected in PARALLEL. Using AW's new 18650 cells you will get 5200mAh capacity at 3.7 volt...
    Being that the cells are parallel you will not have enough volts to power a ROP.Not to mention that it has no switch tower.
    My girlfriend said if I bought one more light she would leave me...........I'm sure gonna miss her.

  10. #10
    Flashaholic Hill's Avatar
    Join Date
    Apr 2008
    Location
    MA
    Posts
    318

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Another brilliant and tempting creation.

    My wallet is screaming.....

  11. #11

  12. #12
    Flashaholic* Aircraft800's Avatar
    Join Date
    Apr 2007
    Location
    DFW Texas.
    Posts
    1,487

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    These are so hot! Great idea FM.

    It's a perfect host for a Luminus PhatLight SST-50, Britelumens SST-50 heatsink, D2FLEX V2 Driver, and UCL lens.

  13. #13
    Flashaholic* Linger's Avatar
    Join Date
    Feb 2009
    Location
    Kingston ON
    Posts
    1,437

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Wow.
    Quote Originally Posted by fivemega
    Switch tower is machinned off and ready to install any LED module and controller.
    FM, please include pic with head removed to illustrate top of switch. My question is how much space is for drivers / heatsink. I presume standard such as britelumens or LITEmania's or mac's are expected, please confirm heatsink compatability.
    Installing Quantum Tunneling Composite (QTC) into M@glite Solitare

  14. #14
    Flashaholic* Linger's Avatar
    Join Date
    Feb 2009
    Location
    Kingston ON
    Posts
    1,437

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Quote Originally Posted by ElectronGuru View Post
    This would make a fun ROP host
    Edit: cancel that!
    No it's good, 4xAW IMR 16340, 2s2p.

    (Further, for 2s18650 you could remove the switch, split the top contacts and create a + and -'ve, reverse one of the cells and isolate tail-spring from the case. Maybe modding the tail contacts you could fit in 2s2p18500's...)
    Installing Quantum Tunneling Composite (QTC) into M@glite Solitare

  15. #15

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Quote Originally Posted by Joe_torch View Post
    Does it mean that this host is for LED only?
    Thanks!
    Joe
    Not necessarily but would you spent some time to mode it with 3.7 volt incand?
    -------------------
    Quote Originally Posted by Sgt. LED View Post
    This comes with a plastic lens and reflector correct?

    I'll have to upgrade that.
    Exactly.
    -------------------
    Quote Originally Posted by LightJunk View Post
    Can the LiteMania charger be used?
    Only if you cut output wire and connect it to supplied jack.
    -------------------
    Quote Originally Posted by Linger View Post
    My question is how much space is for drivers / heatsink. I presume standard such as britelumens or LITEmania's or mac's are expected, please confirm heatsink compatability.
    There are more than enough room for any heat sink ever made for M*g D
    Another word, front of C clamp (switch stopper) is completly empty.

    -------------------
    Quote Originally Posted by Linger View Post
    No it's good, 4xAW IMR 16340, 2s2p.
    It's wasting space for 2S/2P 16340
    2S/3P IMR will work better.

    -------------------
    Quote Originally Posted by Linger View Post
    (Further, for 2s18650 you could remove the switch, split the top contacts and create a + and -'ve, reverse one of the cells and isolate tail-spring from the case. Maybe modding the tail contacts you could fit in 2s2p18500's...
    2S/2P 18500 won't fit. Part of batteries are in deep bored out body and can't go inside tail cap.

  16. #16
    Flashaholic* Linger's Avatar
    Join Date
    Feb 2009
    Location
    Kingston ON
    Posts
    1,437

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    brilliant, thank-you.
    Installing Quantum Tunneling Composite (QTC) into M@glite Solitare

  17. #17
    Flashaholic*
    Join Date
    Mar 2008
    Location
    Borneo
    Posts
    750

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    I want to use this great host for a SSC P7 mod.
    What driver should I use?

    Thank you.

  18. #18
    Flashaholic* Techjunkie's Avatar
    Join Date
    Nov 2007
    Location
    in the brightly lit suburbs of NYC (Long Island)
    Posts
    942

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Is there a battery negative contact component not pictured, or does the Mag tailspring somehow touch both of the 18650 neg. terminals at the same time?

  19. #19

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Quote Originally Posted by Techjunkie View Post
    Is there a battery negative contact component not pictured?
    That's true. It's not in the picture.

  20. #20

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Hi,

    for:
    #03 Pewter 1.25D M*g $97

    thanks

    pom70

  21. #21
    Flashaholic*
    Join Date
    Mar 2008
    Location
    Borneo
    Posts
    750

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Quote Originally Posted by LightJunk View Post
    I want to use this great host for a SSC P7 mod.
    What driver should I use?

    Thank you.

    Got it. Thank you very much nailbender .

  22. #22
    Flashaholic*
    Join Date
    Mar 2008
    Location
    Borneo
    Posts
    750

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    A newbie guessing here. Hopefully I am right.

    The tail cap will look like the one Neofab Legion II have with a free spinning notched contact disk.

  23. #23
    Flashaholic*
    Join Date
    Mar 2008
    Location
    Borneo
    Posts
    750

    Default Re: Dual Bored 2P 18650 M*g 1.25D



    #04 Pewter 1.25D M*g $97

    LightJunk

  24. #24

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    #01 Pewter 1.25D M*g $97 nailbender paid shipped
    #02 Pewter 1.25D M*g $97 nailbender paid shipped
    #03 Pewter 1.25D M*g $97 pom70 paid shipped
    #04 Pewter 1.25D M*g $97 LightJunk paid shipped
    ---------------------
    More 1.25D M*gs available

    Please see post #1 for availability.

  25. #25
    Enlightened n_den's Avatar
    Join Date
    Aug 2004
    Location
    In the middle of the pacific
    Posts
    99

    Default Re: Dual Bored 2P 18650 M*g 1.25D



    #05 Pewter 1.25D M*g = $97
    #06 Pewter 1.25D M*g = $97
    $6.00 s/h + $4.00 for next = $10.00
    $204.00
    thanks!! n_den

    Unique Transaction ID #59L76848M71217801
    Chameleon, Romisen RC-N3 Q5, P7 1C, P7 reg 2D, 3xP7 reg 4D, LED Projects, LED Desk Lamp Mods, LED Machinist Block Master Project

  26. #26

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    perfect job. I'm excited.

    One more!

    for

    #01 Red 1.25D M*g $97
    + $10 shipping to international

    thanks!!

    pom70

  27. #27
    Flashaholic 3rdrock's Avatar
    Join Date
    Mar 2008
    Location
    South Florida
    Posts
    264

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    #01 Blue 1.25D M*g $97 + shipping





    Now off to order a SST-90 heatsink.
    Always check for smelling pistakes before posting.

  28. #28
    Flashaholic 3rdrock's Avatar
    Join Date
    Mar 2008
    Location
    South Florida
    Posts
    264

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    It came today,thanks.
    Always check for smelling pistakes before posting.

  29. #29
    Flashaholic erlon's Avatar
    Join Date
    Jun 2008
    Location
    BRAZIL
    Posts
    172

    Default Re: Dual Bored 2P 18650 M*g 1.25D



    Payment sent for #07 Pewter Dual Bored 2P 18650 1.25D M*g + US Shipping

    More details per PM.

    Thank you !

  30. #30

    Default Re: Dual Bored 2P 18650 M*g 1.25D

    Hi

    I will take #8 pewter

    thanks

    Dave

Page 1 of 4 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •