RofisLight        
Page 1 of 6 123456 LastLast
Results 1 to 30 of 155

Thread: Quad XP-G 5.6A 3-mode P60 module 6th Run *close*

  1. #1

    Default Quad XP-G 5.6A 3-mode P60 module 6th Run *close*

    I sell this!

    A new product!

    5.6A 3-mode 3.7V Li-Io battery!
    This module is most suitable for a large-capacity battery!

    A small battery of the capacity.
    When it is the low battery of the electric discharge rate, the module cannot output it.

    The 6th run will be limited to 4.2mA 3-mode 5.6A 3-mode Direct Drive XP-G R4NW & R5CW
    The sale number is 10 in all.

    I begin to sell it for $190(5.6A 3-mode) 180(4.2A 3-mode) $160(Direct Drive) including the EMS postage!

    The GITD(Ultra green/Ultra blue/Pure blue)processing is plus $10.

    This becomes very hot.
    The use battery is with 3.7V Li-Io battery protection circuit.
    If a light becomes hot, please cut the light which is in a dangerous state.
    Please be careful to the handling.
    After understanding, please refer as things mentioned above.

    This light creates excessive heat
    The consecutive lighting is dangerous.
    If a light is overheated, please turn off the light.
    This light may cause eye damage
    This light will burn the skin at close range.
    This light may cause combustibles to ignite


    I sell this custom Quad XP-G P60 module.

    I begin to sell it for $160(DD) $180(4.2A 3-mode) $190(5.6A 3-mode)including the EMS postage!

    This light creates excessive heat.
    Please use 26650 or 26500 or 18650 or 17670 expensive battery of the electric discharge performance.

    The payment is PeyPal.
    Post your order here and I will PM you the total along with my PayPal address.

    Cutter-XPG25RDR5-CW (remodeling board)


    Original board


    Carclo 24mm Quad Optics


    Quad XP-G Module 5600mA 3-mode
    *3 modes: Low-Med-High
    * Voltage input: 3V - 5.5V
    * The memory feature will memorize the last mode


    Quad XP-G Module 4200mA 3-mode
    *3 modes: Low-Med-High
    * Voltage input: 3V - 5.5V
    * The memory feature will memorize the last mode


    Quad XP-G DD Module



    surefire 6P C2 normal body FIVEMEGA 26500


    Last edited by kerberos0023; 04-26-2011 at 03:25 PM.

  2. #2

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    5.6A 3-mode
    1) erlon R4 3-mode Ultra blue GITD *Order Shipped*
    2) WarriorOfLight R5 3-mode Pure blue GITD *Order Shipped*
    3) doctor ladd R5 3-mode *Order Shipped*
    4) fabienne 90CRI 3-mode Ultra blue GITD *Order Shipped*
    5) WarriorOfLight 90CRI 3-mode Ultra blue GITD *Order Shipped*

    4.2A 3-mode
    1) luopo R5 3-mode green GITD *Order Shipped*
    2) UnderTheWeepingMoon R4 3-mode green GITD *Order Shipped*
    3) baldo21 R5 3-mode Pure blue GITD *Order Shipped*
    4) GhostReaction R5 3-mode green GITD *Order Shipped*

    2.8A 3-mode
    1) calipsoii Nichia 119 3-mode Pure blue GITD *Order Shipped*

    2.1A 3-mode
    1) Lance Carbuncle Nichia 119 3-mode *Order Shipped*
    Last edited by kerberos0023; 01-01-2012 at 01:26 AM.

  3. #3

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Hope you are okay- that was a massive earthquake
    Surefire 18650 Bored Hosts & Cerakote!
    I am visually impaired please excuse my typos =P

  4. #4
    Flashaholic warmurf's Avatar
    Join Date
    Oct 2010
    Location
    Queensland Australia
    Posts
    350

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Hey Kenji,

    Same sentiments here, hope you and your family are all OK. First thing I though of when hearing of the quake was you.

    Trusting that you're OK, just wanted to update you on my quad. It is now housed in a Solarforce L2X, with an IMR and zero resistance Moddoolar Triad tail with clip. It looks unreal (real mean, like it means business!), but the output is AWESOME!!! I just hope this combo is not cooking the drop-in, but for outright "light" all around, the output of this thing defies description. I now carry it everywhere.

  5. #5

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by bugsy714 View Post
    Hope you are okay- that was a massive earthquake
    Quote Originally Posted by warmurf View Post
    Hey Kenji,

    Same sentiments here, hope you and your family are all OK. First thing I though of when hearing of the quake was you.

    Trusting that you're OK, just wanted to update you on my quad. It is now housed in a Solarforce L2X, with an IMR and zero resistance Moddoolar Triad tail with clip. It looks unreal (real mean, like it means business!), but the output is AWESOME!!! I just hope this combo is not cooking the drop-in, but for outright "light" all around, the output of this thing defies description. I now carry it everywhere.
    Hi,

    I am all right.
    Thank you very much.
    Last edited by kerberos0023; 03-11-2011 at 11:23 AM.

  6. #6

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by kerberos0023 View Post
    Hi,

    I am all right.
    Thank you very much.
    Glad to hear this!!!!!!!


  7. #7
    Flashaholic
    Join Date
    Feb 2007
    Location
    NJ
    Posts
    345

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    I would like one 5.6A with GITD (pure blue I think). I think I would want a NW R4 but would like to know the color temperature and/or tint of both it and the CW if you know please. Also, what is the difference between ultra blue and pure blue? Will it fit the FM Copper 26650 and what other hosts are great fits.

    Please also PM your PayPal address, total, how long for delivery to New Jersey, USA and anything else. I will send you a PM too JIC.

    Thank you,

    Pablo

  8. #8

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by Disintergrator66 View Post
    Glad to hear this!!!!!!!

    Hi Disintergrator66,

    Thank you very much.

  9. #9
    Flashaholic* stoli67's Avatar
    Join Date
    Jul 2010
    Location
    Sydney Austalia
    Posts
    926

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Kenji

    Good to here that u r ok!

    The higher amp drop in looks good

    What are the output levels for the 5.6 at high-medium & low

  10. #10

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by paulsl View Post
    I would like one 5.6A with GITD (pure blue I think). I think I would want a NW R4 but would like to know the color temperature and/or tint of both it and the CW if you know please. Also, what is the difference between ultra blue and pure blue? Will it fit the FM Copper 26650 and what other hosts are great fits.

    Please also PM your PayPal address, total, how long for delivery to New Jersey, USA and anything else. I will send you a PM too JIC.

    Thank you,

    Pablo
    Hi Pablo,

    I sent PM!

    Thanks,
    Kenji

  11. #11

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by stoli67 View Post
    Kenji

    Good to here that u r ok!

    The higher amp drop in looks good

    What are the output levels for the 5.6 at high-medium & low
    Hi stoli67,

    The output value of each mode of the 5.6A module will measure it tomorrow.

    Thanks,
    Kenji

  12. #12

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by kerberos0023 View Post
    Hi stoli67,

    The output value of each mode of the 5.6A module will measure it tomorrow.

    Thanks,
    Kenji
    Hi,

    Can you give the values of the 4.2A also. Thanks!

  13. #13
    Flashaholic* stoli67's Avatar
    Join Date
    Jul 2010
    Location
    Sydney Austalia
    Posts
    926

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    thanks for that....

    The DD is great but sometimes it would be good to use med and let it cool down!

  14. #14

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by tpetsch View Post
    Hi,

    Can you give the values of the 4.2A also. Thanks!
    It is OK!

  15. #15
    Flashaholic* stoli67's Avatar
    Join Date
    Jul 2010
    Location
    Sydney Austalia
    Posts
    926

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Kenji,

    with the DD I know I can't use an IMR cell so I guess that I am limited to an AW18650

    Could I use an IMR 26650 or 32650 with the new 5.6 amp 3 mode drop in?

  16. #16

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by stoli67 View Post
    Kenji,

    with the DD I know I can't use an IMR cell so I guess that I am limited to an AW18650

    Could I use an IMR 26650 or 32650 with the new 5.6 amp 3 mode drop in?
    Yes,

    4.6A module and 5.6A module can use IMR26650 and 32650.

  17. #17

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Kenji, PM sent for a 4.2a 3 mode with the Green GITD. Thanks!

  18. #18

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by luopo View Post
    Kenji, PM sent for a 4.2a 3 mode with the Green GITD. Thanks!
    Hi luopo,

    I sent PM!

    Thanks,
    Kenji

  19. #19

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Hi,

    It is the current value that it measured by a clamp meter.
    The use battery is AW IMR18650.
    It is the measurement value in the module simple substance.

    5.6A 3-mode
    H : 5.37A
    M : 1.44A
    L : 0.19A

    4.2A 3-mode
    H : 4.14A
    M : 1.26A
    L : 0.17A

  20. #20

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Hi luopo,

    I received payment.

    Thank you very much!
    Kenji

  21. #21
    Flashaholic tshirley's Avatar
    Join Date
    Apr 2010
    Location
    Jackson Hole Wyoming
    Posts
    135

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Kenji glad to hear you are ok. Have one of these quad modules and love it. Anyway be safe.

    Travis

  22. #22

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by tshirley View Post
    Kenji glad to hear you are ok. Have one of these quad modules and love it. Anyway be safe.

    Travis
    Hi Travis,

    Thank you very much!
    Kenji

  23. #23

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Hi,

    Could i plz get a XP-G R4NW 4.2A 3-mode 3-mode green GITD.

    Do you ship to Canada? (thought i would ask)

    Hope you, your friends, and your family is alright.


    Regards,

    Daniel
    Last edited by GoldenF1; 03-15-2011 at 11:30 AM.

    I reject your reality and substitute my own!

  24. #24
    Flashaholic* stoli67's Avatar
    Join Date
    Jul 2010
    Location
    Sydney Austalia
    Posts
    926

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Kenji,

    Would I be correct to thint that the Direct Drive Drop-in that I have would work with the new 4sevens 26650 cell.... I believe that it is protected.

    http://www.4sevens.com/product_info....oducts_id=2585


    Andrew

  25. #25

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by GoldenF1 View Post
    Hi,

    Could i plz get a XP-G R4NW 4.2A 3-mode 3-mode green GITD.

    Do you ship to Canada? (thought i would ask)

    Hope you, your friends, and your family is alright.


    Regards,

    Daniel
    Hi GoldenF1,

    I sent PM!

    Thanks,
    Kenji

  26. #26

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by stoli67 View Post
    Kenji,

    Would I be correct to thint that the Direct Drive Drop-in that I have would work with the new 4sevens 26650 cell.... I believe that it is protected.

    http://www.4sevens.com/product_info....oducts_id=2585


    Andrew
    Hi Andrew,

    LED may be damaged when I drive a DD module in 26650 cells of 4sevens.

    Battery capacity and relations of the ability for electric discharge come over, and an excessive electric current may flow through the reason.

    I recommend QUAD controlled with a converter.

    Thanks,
    Kenji

  27. #27
    Flashaholic* stoli67's Avatar
    Join Date
    Jul 2010
    Location
    Sydney Austalia
    Posts
    926

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    OK I may have to put my DD up on the Market Place and get a 5.6 amp 3 level instead because i want to put it in one of my new FM 26650 hosts....

  28. #28

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by stoli67 View Post
    OK I may have to put my DD up on the Market Place and get a 5.6 amp 3 level instead because i want to put it in one of my new FM 26650 hosts....
    Hi Andrew,

    I wait for an order from you!

    Thanks,
    Kenji

  29. #29

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Kenji,

    I am am VERY glad to hear you are OK and back on CPF. I am loving my 2 Quads and the 4.2 amp version is a particular favorite.

    I have one question, when running on high, will the module blink or step down in brightness if the battery voltage drops below a certain level? Just curious as I have not run it this long yet, but wanted to know what to expect if I did.

    Thanks,
    D

  30. #30

    Default Re: Quad XP-G 5.6A 3-mode P60 module 6th Run

    Quote Originally Posted by Darvis View Post
    Kenji,

    I am am VERY glad to hear you are OK and back on CPF. I am loving my 2 Quads and the 4.2 amp version is a particular favorite.

    I have one question, when running on high, will the module blink or step down in brightness if the battery voltage drops below a certain level? Just curious as I have not run it this long yet, but wanted to know what to expect if I did.

    Thanks,
    D
    Hi Darvis,

    Thank you for using my module habitually.

    The lighting of the high mode please make around 10 minutes a limit.
    If the right field becomes the high temperature, please change it in mid or low.

    Thanks,
    Kenji

Page 1 of 6 123456 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •