First Couple 4 Sevens clips mods

fenix-store
Got Lumens?

Got Lumens?

Flashlight Enthusiast
Joined
Mar 12, 2011
Messages
2,461
Location
Champlain Valley
If wrong forum, I appologize.
Heres a couple of pics of the first clip mods I've done. These are two prototype clip mods.
The next version will be done using a mill and round table to inset the top of the clips.

. :D .
 
P

Potato42

Newly Enlightened
Joined
Feb 9, 2010
Messages
106
Cool. I tried using the clip from my zebralight on my quark, but it doesn't stay put when I clip it to my pocket. I'd be in for one of these if it works well.
 
L

lpd226

Newly Enlightened
Joined
Mar 10, 2011
Messages
44
Is that a turbo head on a single 123 body??!! If so what are the specs on that. Runtimes ETC.
 
Got Lumens?

Got Lumens?

Flashlight Enthusiast
Joined
Mar 12, 2011
Messages
2,461
Location
Champlain Valley
That Is a Quark Turbo XP-G R5 LV Head, a 123 single battery tube, a atandard tail switch with blue rubber, a standard Quark clip.
Formed, drilled, tapped, painted, and installed.
Runtimes vary based on battery, But it works great! I use RCR123 Protected Lions :thumbsup:
Simular ~45Min Max ~8Hours Med, haven't tried any others.

lpd226 said:
Is that a turbo head on a single 123 body??!! If so what are the specs on that. Runtimes ETC.
Click to expand...

The Second is a Quark Mini Cr2, with a standard Quark clip. I can't wait to start/finish Version 2 with the milled mini with flush clip ring installed!
 
Last edited:
ma_sha1

ma_sha1

Flashlight Enthusiast
Joined
Jan 10, 2009
Messages
3,042
Location
CT, USA
Cool, If you don't mind, here is my quark clip joining the party :).

It's Ti Quark Clip on my Stainless Mac EDC clone:
img3830i.jpg
 
Last edited:
Got Lumens?

Got Lumens?

Flashlight Enthusiast
Joined
Mar 12, 2011
Messages
2,461
Location
Champlain Valley
Very nice looking, a very clean installation :thumbsup:
Has the tail and cap been turned on a lathe to make clip ring fit inside cap?

ma_sha1 said:
Cool, If you don't mind, here my quark cliip joining the party :).

It's Ti Quark Clip on my Stainless Mac EDC clone:
Click to expand...
 
ma_sha1

ma_sha1

Flashlight Enthusiast
Joined
Jan 10, 2009
Messages
3,042
Location
CT, USA
I don't have a lathe, it's all done by hand tools. A grinder & a file.
The clip ring goes inside in between the two sections that I jointed together.
 
Last edited:
You must log in or register to reply here.

Similar threads

G
4C & 6C Maglite LED mods
2 3
Replies
40
Views
4K
PCC
P
M
4D MAG-LITE 4 26650'S for 12.8vdc.
Replies
0
Views
467
mrfixitman
M
mcbrat
Finished up a couple lights finally
Replies
4
Views
1K
nbp
nbp
N
Total Newbie's First Build
Replies
1
Views
915
HarryN
H
mcbrat
A couple customer orders in progress.
Replies
7
Views
1K
mcbrat
mcbrat

Latest posts

Top