luxlunatic
Flashlight Enthusiast
Up for sale is a nearly mint Ti Ra Clicky #10035.
2 different custom Ti clips are included. One is bezel up only, deep pocket (by member wvaltakis2)and mounts to the holes tapped into the body (lower right pic), the other (by member Moddoo) can accomodate bezel up or bezel down (bezel up mounting in upper right pic). For bezel down, it is placed between the tailcap and batt tube.
Here are some pics!
What all is included here:
Ti Ra Clicky
2 custom Ti clips
2 of Dads "Get Screwed" hole filler screws with hex key (seen in upper right pic).
2 Button head screws for 'Bezel up only clip" (no hex key).
Owners manual.
Quick reference card.
Stock clip.
Both of the custom Ti clips have had the edges smoothed down by me. Most clips come with a raw, jagged edge that over a short time will chew through most anything you clip it to, namely pants! Besides, a somewhat "raw" clip does look out of place on such a beautifuly finished light so with the edges smoothed, not only does the clip work better, it looks and feels better as well!
Now, I said nearly mint because I am the second owner and there are a few nicks. One in the tail and one in the bezel. Quite small and not really noticeable but they are there and more appearant in some nice macro shots below. Also, when I received the light, I noticed a small finger print on the reflector. It bugged me but not enough to relace it and I doubt it has any signifigant impact on output or beam pattern, replacing would be mostly asthetic. Here are the shots:
Here are the factory specs for the light:
Titanium body - Built like a tank.
170 lumens, narrower beam for longer throw.
Sapphire lens with anti-reflective coatings, fully shock mounted.
4 preset brightness settings. The brightness settings and the turn-on setting may be customized for special missions.
1.25 hours typical runtime on High setting, one hour minimum.
Constant brightness through constant power regulation
Graceful low battery warning.
Designed for both primary lithium batteries and rechargeable lithium-ion batteries. Protects rechargeable batteries from over-discharge.
Full thermal management.
Potted electronics for the ultimate in reliability under extreme conditions.
Anti-damage battery compartment protects battery under extreme conditions.
Customizations include turn-on setting, momentary operation, automatic shut-off, button lock, locator flash. Output settings can include burst output, tactical strobe, emergency strobe and emergency SOS or any brightness level.
Reverse battery polarity protection without diode power penalty.
Pocket clip, deep carry bezel up, MOLLE compatible, retaining.
Water resistance: 2 atmospheres (20m or 66 feet of water) - static.
Weight: 122g (4.3oz) including battery.
Price is $725. *SOLD*
Paypal only.
First Ill take it in this thread has priority.
Paypal fees and shipping to CONUS included in price.
Priority shipping with delivery conformation.
Not interested in trades at this time.
Thanks for looking!
__________________
__________________
2 different custom Ti clips are included. One is bezel up only, deep pocket (by member wvaltakis2)and mounts to the holes tapped into the body (lower right pic), the other (by member Moddoo) can accomodate bezel up or bezel down (bezel up mounting in upper right pic). For bezel down, it is placed between the tailcap and batt tube.
Here are some pics!
What all is included here:
Ti Ra Clicky
2 custom Ti clips
2 of Dads "Get Screwed" hole filler screws with hex key (seen in upper right pic).
2 Button head screws for 'Bezel up only clip" (no hex key).
Owners manual.
Quick reference card.
Stock clip.
Both of the custom Ti clips have had the edges smoothed down by me. Most clips come with a raw, jagged edge that over a short time will chew through most anything you clip it to, namely pants! Besides, a somewhat "raw" clip does look out of place on such a beautifuly finished light so with the edges smoothed, not only does the clip work better, it looks and feels better as well!
Now, I said nearly mint because I am the second owner and there are a few nicks. One in the tail and one in the bezel. Quite small and not really noticeable but they are there and more appearant in some nice macro shots below. Also, when I received the light, I noticed a small finger print on the reflector. It bugged me but not enough to relace it and I doubt it has any signifigant impact on output or beam pattern, replacing would be mostly asthetic. Here are the shots:
Here are the factory specs for the light:
Titanium body - Built like a tank.
170 lumens, narrower beam for longer throw.
Sapphire lens with anti-reflective coatings, fully shock mounted.
4 preset brightness settings. The brightness settings and the turn-on setting may be customized for special missions.
1.25 hours typical runtime on High setting, one hour minimum.
Constant brightness through constant power regulation
Graceful low battery warning.
Designed for both primary lithium batteries and rechargeable lithium-ion batteries. Protects rechargeable batteries from over-discharge.
Full thermal management.
Potted electronics for the ultimate in reliability under extreme conditions.
Anti-damage battery compartment protects battery under extreme conditions.
Customizations include turn-on setting, momentary operation, automatic shut-off, button lock, locator flash. Output settings can include burst output, tactical strobe, emergency strobe and emergency SOS or any brightness level.
Reverse battery polarity protection without diode power penalty.
Pocket clip, deep carry bezel up, MOLLE compatible, retaining.
Water resistance: 2 atmospheres (20m or 66 feet of water) - static.
Weight: 122g (4.3oz) including battery.
Price is $725. *SOLD*
Paypal only.
First Ill take it in this thread has priority.
Paypal fees and shipping to CONUS included in price.
Priority shipping with delivery conformation.
Not interested in trades at this time.
Thanks for looking!
__________________
__________________
Last edited: