nailbender
Flashlight Enthusiast
NEW XML2 90 + HIGH CRI P60 / D26 Replacement Modules
These are XML2 emitters (XMLBWT000US60Z7) 3000k 90 cri emitters, S6 flux is the highest flux available in 90CRI. As with all XML2 emitters they have pretty good throw with a adequate amount of spill.
As with most warm white emitters these look much like a incan and the color rendition is great. At S6 flux it is the highest lumen Hi CRI single emitter
As with most XML2's both smooth and op reflectors are available. The smooth gives the best throw with a distinct hotspot while the Op will yield a slightly floodier and more blended beam.
Please let me know if you are using in a Solarforce product as they can use a longer module.
NOW MOUNTING EMITTERS ON ALL COPPER DIRECT BOND SINKPADS
Available in the following levels
3 amp regulated with last mode memory. (2.8v - 6v )
These have reverse polarity protection and low voltage protection
While these can be ran at higher amperage you are paying for a certain tint and rating and above 3.0 amps the tints may not be true as designed.
Also available in a 2.2 amp (3.6-16volt) One level
__________________________________________________________________________________________________
Price is $40 Includes free shipping in the US / free potting and 1 pc of Copper tape included in price.
International shipping is $12 for 1st class Int. and $23.95 for priority mail Int.
Paypal addy is in my Bio / please include CPF nickname and what ordered in paypal notes and below in thread.
MAKE SURE YOUR ADDRESS IS SHOWING IN PAYPAL OR INCLUDE IN NOTES
Dont forget to specify smooth or Op reflector if not listed Op will be installed.
Below is a beam shot, it is not quite that beige looking in real life but a bit more incan looking. It must have been picking up the slightly off white walls.
These are XML2 emitters (XMLBWT000US60Z7) 3000k 90 cri emitters, S6 flux is the highest flux available in 90CRI. As with all XML2 emitters they have pretty good throw with a adequate amount of spill.
As with most warm white emitters these look much like a incan and the color rendition is great. At S6 flux it is the highest lumen Hi CRI single emitter
As with most XML2's both smooth and op reflectors are available. The smooth gives the best throw with a distinct hotspot while the Op will yield a slightly floodier and more blended beam.
Please let me know if you are using in a Solarforce product as they can use a longer module.
NOW MOUNTING EMITTERS ON ALL COPPER DIRECT BOND SINKPADS
Available in the following levels
3 amp regulated with last mode memory. (2.8v - 6v )
These have reverse polarity protection and low voltage protection
- 1 level
- 3 level (low 5% / med 30% / hi 100%)
- 3 level (low 5% / hi / Strobe)
- 5 level (Moonlight / low 5% / med 30% /med high 40% / hi100% )
While these can be ran at higher amperage you are paying for a certain tint and rating and above 3.0 amps the tints may not be true as designed.
Also available in a 2.2 amp (3.6-16volt) One level
__________________________________________________________________________________________________
Price is $40 Includes free shipping in the US / free potting and 1 pc of Copper tape included in price.
International shipping is $12 for 1st class Int. and $23.95 for priority mail Int.
Paypal addy is in my Bio / please include CPF nickname and what ordered in paypal notes and below in thread.
MAKE SURE YOUR ADDRESS IS SHOWING IN PAYPAL OR INCLUDE IN NOTES
Dont forget to specify smooth or Op reflector if not listed Op will be installed.
Below is a beam shot, it is not quite that beige looking in real life but a bit more incan looking. It must have been picking up the slightly off white walls.
Last edited: