Lummi Raw Triple

Hi everyone,

I have two favorite lights. One is Mac's Tri EDC. The other is Lummi Raw.
So I decided to make Lummi raw triple.

I used nichia 219 20mm triple star and carclo 10507.
The driver is 4×7135 3mode driver.Two 7135 is removed.700ma setting on high.
These are from illumination suply.

At first I cut a lens and a triple star and a driver to 16mm in diameter.


And I stuck 16mm MCPCB on a triple star as a substitute for a heat sink.


Completion of the drop-in.


Finished





Beamshot:low


mid



high


Thank you for looking.

zanzan

Very nice. What is the run time on high. Is heat a issue?

Mohan

Nice mod :thumbsup: The GITD looks cool.

I still have my Orb Raw NS back from 2006. I don´t carry it anymore but keep it for sentiment and since it was my first custom light. I guess with innards like yours it would end up in my pockets again.

Eric

Zanzan

Just ordered the parts from Craig. Can you tell me how you mounted the positive and negative contacts onto the driver board. Did you use the original Lummi board or mount a positive contact plate onto the driver? I am not familiar with this driver board .

That looks Amazing! Would you be interested in making one for me? If so, how much?

+1

Excellent!
I would be interested should you decide to make more.

Megatrowned said:

That looks Amazing! Would you be interested in making one for me? If so, how much?

Click to expand...

Light11 said:

+1

Excellent!
I would be interested should you decide to make more.

Click to expand...

+2 I would also be interested!

Hi,

Thanks for interest.

I'm sorry.
I forgot to write an important thing in making it.

I removed the spring in the tail. And I put a magnet of 3mm to see the button top of the battery from the side.
Finally I attached a spring to the backside of the driver.




zanzan

mohanjude said:

Very nice. What is the run time on high. Is heat a issue?

Mohan

Click to expand...

Hi Mohan,

Thank you.

Run time on high is about 25min.
Mideum:85min
Low:8.5hour

I hold it in my hand on high for five minutes.
However, it did not have a fever as I could not hold it.

Eric242 said:

Nice mod :thumbsup: The GITD looks cool.

I still have my Orb Raw NS back from 2006. I don´t carry it anymore but keep it for sentiment and since it was my first custom light. I guess with innards like yours it would end up in my pockets again.

Eric

Click to expand...

HI Eric,

Thank you.
I'm glad that your Lummi Raw can regain brightness again.

zanzan

I find your triple very interesting.
I'm looking into making a 3 LED light to get more then 2500 lumens.
Where do you get all the components?

mohanjude said:

Zanzan

Just ordered the parts from Craig. Can you tell me how you mounted the positive and negative contacts onto the driver board. Did you use the original Lummi board or mount a positive contact plate onto the driver? I am not familiar with this driver board .

Click to expand...

Hi Mohan,

I didn't use the original Lummi board.
I use only the driver board from illuminations supply.

picture of driver board


Outside gold plate is negative contacts, and inside gold plate is positive contact.
The negative contact scrapes the inside obstacle of the head.
The positive contact scrapes the plus of the battery.

Like this


OK?

zanzan

Zanzan

Thank you very much. The photos are excellent and now I understand it is all put together. I notice you use copper foil for better contact with negative terminal and body of torch.

Now I wait for Craig to send the parts. Looking forward to doing this mod. Thank you the brilliant idea.

Pizeer said:

I find your triple very interesting.
I'm looking into making a 3 LED light to get more then 2500 lumens.
Where do you get all the components?

Click to expand...

Hi Pizeer,

Thank you for interest.
I got those here.

zanzan

Hi zanzan,

looks similtar to my raw:

http://www.candlepowerforums.com/vb...-amp-two-red-selfprogrammed-Driver&highlight=

great work. i think there will me much light loss during the sanding of the tir optics. i made my one with small lenses to collect much light as possible...

markus

mash.m said:

Hi zanzan,

looks similtar to my raw:

http://www.candlepowerforums.com/vb...-amp-two-red-selfprogrammed-Driver&highlight=



great work. i think there will me much light loss during the sanding of the tir optics. i made my one with small lenses to collect much light as possible...

markus

Click to expand...

Hi Markus,

Wow!!! 8 led emitter!? Awesome mods. Excellent work.
Smd is very cool.
I refer to it.

zanzan

Megatrowned said:

That looks Amazing! Would you be interested in making one for me? If so, how much?

Click to expand...

I am considering whether I will update my Lummi raw now.
Please give me time for a while.

zanzan

Whoa, cool. I had no idea you could do this type of thing with torches. Thats awesome man. Really cool.

Thanks zanzan
Very nice mod.
:twothumbs



I'm looking to built a dive light using 3 LEDs.
I want to use a one mode driver, does that exist?




[h=1]Thread: DIY Powerfull LED Dive Light[/h]

Pizeer said:

Thanks zanzan
Very nice mod.
:twothumbs



I'm looking to built a dive light using 3 LEDs.
I want to use a one mode driver, does that exist?






Thread: DIY Powerfull LED Dive Light

Click to expand...

Hi Pizeer,

Thanks.
2500lm at 3LED?
I think that you need to use 3 XM-L U2 emitter and This board(9A).

zanzan