Klarus        
Page 11 of 11 FirstFirst ... 4567891011
Results 301 to 315 of 315

Thread: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

  1. #301
    peter yetman's Avatar
    Join Date
    Mar 2014
    Location
    North Norfolk UK
    Posts
    4,302

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Nuffin"
    Last edited by peter yetman; 02-24-2018 at 12:09 PM.
    Peter's shopping list:- HDS / Oveready 170N Exec/LE and an Oveready V4 Nichia Drop In. Otherwise I'm content. Want want want, that's me.

  2. #302

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by peter yetman View Post
    Check your serial number by counting the groups of red flashes when the light in in programming mode. Put the serial number in here...

    http://lux-rc.com/content/serials

    This will tell you the furmware version that you have. Version 1.1 did not have the battery check, apparently, version 1.2 did
    Correct, thank you. Here are complete release notes:


    R1.0 Apr 15, 2015
    - Beta board for OR, power pulse UI (requires special
    web timing)

    R1.1 Jun 1, 2015
    - Programming timing fixed to support all screens
    - 0.7s default mode switch time, "222" factory PIN

    R1.2 Nov 17, 2015
    - The voltage tracking/state machine full redesign
    - 1S/2S voltage display
    - Bat safety switchover (up to ~50mOhms internal res)
    - Hybrid memory revision. Selection is saved after 2s
    - MOM: on/off, mode switching, three special modes and
    programming, lock, program with holding mom, FL33 RGB

    R1.2 Dec 18, 2015
    - The battery lock leak fixed

    R1.2 Dec 31, 2015
    - The PIN enter click is set to 1/2s limit

    R1.2.1 Feb 22, 2016
    - Temperature and bounce reading fixes (stepdown issue)
    - Extra low mode (signal) switching fix (decay monitor)
    - Low-battery occasional mode switchover fix
    - 1S heavy load surge detector added. Steps down to 3W
    - Access voltage meter with MOM (lock and hold)
    - Cap discharge optimization (mode switching improvement)
    - FL33 RGB indicator fix
    - 8ms temperature reading (leads to web app re-calibration)
    - Bat. fail/lock: 7-10uA leak, waits for battery swap
    - OVP: overvolt. check on start, no runtime checking

    R1.2.2 Feb 24, 2016
    - mode saving to EEPROM fixed (FL_NOTSAVED)

    R1.2.3 Mar 7, 2016
    - 481 service PIN added: on/off the standby locator

    R1.2.4 Mar 22, 2016
    - "No memory" bug fixed

    R1.2.5 Apr 27, 2016
    - Service PIN fix: use 381 to control the standby locator
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

  3. #303

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    What is 481 service PIN added: on/off the standby locator?
    4500k XPL RD BOSS • 4000k 219C BOSS Ti • 2700k HDS Rotary

  4. #304

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Stoneking View Post
    What is 481 service PIN added: on/off the standby locator?
    And how do you use it?
    #75

  5. #305

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Hi folks
    I am having trouble with the bounce option.
    I can successfully change program outputs,currently have .04,14,74 and afterburner.
    i have tweaked the bounce sensitivity from 60 to 76% but the bounce function has never worked.
    Any suggestions would be appreciated.

  6. #306

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by scintillator View Post
    Hi folks
    I am having trouble with the bounce option.
    I can successfully change program outputs,currently have .04,14,74 and afterburner.
    i have tweaked the bounce sensitivity from 60 to 76% but the bounce function has never worked.
    Any suggestions would be appreciated.
    Turn it to 100%, then work your way down until it works right. Mine is set to 89/90ish.

  7. #307

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    That did it,thank you

  8. #308
    Flashaholic
    Join Date
    Feb 2006
    Location
    Raleigh, NC
    Posts
    119

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Are the limited copper e-series heads from several years ago old e or new e?

  9. #309

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Shurock View Post
    Are the limited copper e-series heads from several years ago old e or new e?
    I'm 90% sure they are newest possible E, they even came in modern cardboard. Let me know if a photo would help.
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

  10. #310
    Flashaholic* id30209's Avatar
    Join Date
    Mar 2008
    Location
    Europe
    Posts
    1,715

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Subscribed....i see i'll spend, AGAIN, more money then i should

  11. #311

    Join Date
    Jul 2012
    Location
    Kansas City
    Posts
    3,170

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    What's the status on the V5 Wasp engine upgrade offering?

  12. #312

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Grizzman View Post
    What's the status on the V5 Wasp engine upgrade offering?
    Its actually ready to go
    https://www.oveready.com/flashlight/...-led-pcb-20mm/

    but I'm waiting for a good board selection/stocks before making announcements, which could be just a few weeks
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

  13. #313
    Administrator Kestrel's Avatar
    Join Date
    Oct 2007
    Location
    Willamette Valley, OR
    Posts
    6,495

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    So with regards to the Level 1 / 1.5mw output mode; now that this product has been out for a while, does anybody have an estimate for potential runtime at this lowest level (w/ any cell) ?
    A straight calculation from the cited runtimes for the higher levels (i.e. listed in Post #1) is almost certainly not accurate due to the board/driver overhead during operation.

    Was thinking that perhaps someone has been able to measure 'tailcap' current or ... ?

    Edit: And has anyone done any runtimes at all with 2xCR123 (any output level) ? Thx,
    Last edited by Kestrel; 06-14-2019 at 06:31 PM.

  14. #314

    Default Re: Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    I haven’t seen this discussed anywhere, but will the new engine in the luxrc fj33 be making its way into a boss or wasp head?

  15. #315

    Default Triple v5 R33 Engine - 4th LED, 30w limit, Screen Programable, Dual Mode Groups

    Quote Originally Posted by Kestrel View Post
    Edit: And has anyone done any runtimes at all with 2xCR123 (any output level) ? Thx,
    sorry, mode 1 is so efficient it would take months to find out



    Quote Originally Posted by tangomongo View Post
    I haven’t seen this discussed anywhere, but will the new engine in the luxrc fj33 be making its way into a boss or wasp head?
    Sorry, the driver for that light is significantly larger than the one in the BOSS. any new light we develop would be a second larger platform parallel to BOSS etc and wouldn't be ready until 2020.
    Last edited by ElectronGuru; 06-22-2019 at 01:47 PM.
    Control the Dark

    OR Facebook | OR Forum
    | OR Insider | OVEREADY.com

Page 11 of 11 FirstFirst ... 4567891011

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •