Imalent        
Results 1 to 7 of 7

Thread: Extreme Micro Questions

  1. #1
    Flashaholic* KuanR's Avatar
    Join Date
    Jan 2012
    Location
    Macau S.A.R.
    Posts
    1,802

    Default Extreme Micro Questions

    I'm looking at the Extreme Micro in titanium and have a few questions.

    Does the light have a H-M-L or L-M-H mode sequence?
    Does it work with PWM or constant current?
    Will it work on a regualr CR2 cell with reduced output?

    Hoping someone could help me out before I make up my mind, thank you.
    I'm Ryan.

  2. #2
    Moderator
    archimedes's Avatar
    Join Date
    Nov 2010
    Location
    CONUS, top left
    Posts
    13,376

    Default Re: Extreme Micro Questions

    I think @magellan may be able to answer, if he sees this thread ....
    ... is the archimedes peak

  3. #3
    Flashaholic*
    Join Date
    Mar 2003
    Location
    Southern California
    Posts
    1,082

    Default Re: Extreme Micro Questions

    I have used both variations. I believe the last ones were L-M-H.
    It is a PWM driver
    The light is designed for 3.7v cells. It might light on a CR2 cell but only in the lowest setting and probably not for very long. the CR2 is pretty much at the battery protection cutoff voltage. These were designed to use the IMR 15270 batteries.

    Hope this helps.


    Quote Originally Posted by KuanR View Post
    I'm looking at the Extreme Micro in titanium and have a few questions.

    Does the light have a H-M-L or L-M-H mode sequence?
    Does it work with PWM or constant current?
    Will it work on a regualr CR2 cell with reduced output?

    Hoping someone could help me out before I make up my mind, thank you.
    (TnC Products) (Made in U.S.A)
    Click Here to Send an E-mai(909) 923-5311 M-Th 6am-3pm Friday 6am-12noon PST

  4. #4

    Default Re: Extreme Micro Questions

    Quote Originally Posted by archimedes View Post
    I think @magellan may be able to answer, if he sees this thread ....
    Not really helpful.

  5. #5
    Moderator
    archimedes's Avatar
    Join Date
    Nov 2010
    Location
    CONUS, top left
    Posts
    13,376

    Default Re: Extreme Micro Questions

    Did you PM him ?
    ... is the archimedes peak

  6. #6
    Flashaholic* KuanR's Avatar
    Join Date
    Jan 2012
    Location
    Macau S.A.R.
    Posts
    1,802

    Default Re: Extreme Micro Questions

    Hey Chris,

    Thanks for answering my questions.I was really hoping to run CR2 cells and have a battery vampire that could drain it to the last bit of usable power.

    Quote Originally Posted by TnC_Products View Post
    I have used both variations. I believe the last ones were L-M-H.
    It is a PWM driver
    The light is designed for 3.7v cells. It might light on a CR2 cell but only in the lowest setting and probably not for very long. the CR2 is pretty much at the battery protection cutoff voltage. These were designed to use the IMR 15270 batteries.

    Hope this helps.
    I'm Ryan.

  7. #7
    Flashaholic*
    Join Date
    Mar 2003
    Location
    Southern California
    Posts
    1,082

    Default Re: Extreme Micro Questions

    I am not sure one of my 1-watt drivers would fit in this light. If I have a 1-watt driver it would most likely be a single mode. Driving an LED at 350mA.
    (TnC Products) (Made in U.S.A)
    Click Here to Send an E-mai(909) 923-5311 M-Th 6am-3pm Friday 6am-12noon PST

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •