**************** SOLD/PENDING ITEMS BELOW ******************
http://www.indysworld.com/sale/sale-group.jpg
No batteries included. Shipping included in USA, if outside, PM.
Mac's Customs SST-50 Knurly in Aluminum: the very first Mac's knurly. $425 - SOLD $500 $525 $550 $600
Original thread: http://www.candlepowerforums.com/vb/showthread.php?246903-quot-Knurly-quot-SST-50
In my knurly quest, I traced it through owners, and aquired it... as some point, the engine was modified for higher output.
This is the same length as the first run EDC lights that used a shorter reflector. it currently has in it my triple conversion pill (which I had to shorten to fit), running a Qlite 3.05A driver with 3-up XP-L from MtnElectronics.
Will include the original single emitter engine.
16340 body, but could be bored for 18350.
http://www.indysworld.com/sale/first-knurly-1.jpg
http://www.indysworld.com/sale/first-knurly-2.jpg
http://www.indysworld.com/sale/first-knurly-3.jpg
http://www.indysworld.com/sale/first-knurly-4.jpg
http://www.indysworld.com/sale/first-knurly-5.jpg
http://www.indysworld.com/sale/first-knurly-6.jpg
Sinner Copper 18350 Host for laser. $125 - SPF .$150
laser module is non-working. I was going to make a flashlight head for this, but need funds for something else instead... new laser modules for this can be found here:
https://sites.google.com/site/dtrlpf/home/diodes/bdr-209-405nm-16x-diodes
http://www.indysworld.com/sale/sinner-laser-host.jpg
http://www.indysworld.com/sale/sinner-laser-host-2.jpg
Tain Aura Damascus . $700 - SOLD .
stainless damascus. uses 14500 Battery. Ice Blue Trits around tail, red trits in switch. Includes Gamblemade Mokume Gane dangler as shown.
http://www.indysworld.com/sale/Tain-Dam-1.jpg
http://www.indysworld.com/sale/Tain-Dam-2.jpg
Sigma Customs Brass 18650 with Mr. Bulk Big Bulkhead Turbo Head with VoB engine. $450 - SOLD .
BratGuy Ti boot retaining ring, blasted to match.
VoB (Adventure Sport) engine is XP-L HI single emitter.
Sigma Engine: -Nichia 219C D280 5000k 80+ CRI Triple, 3.04A Qlite w/guppydrv, frosted optic, AR lens
http://www.indysworld.com/sale/Sigma-Bulk-1.jpg
http://www.indysworld.com/sale/Sigma-Bulk-2.jpg
Aspheric Okluma TinyDC in Aluminum. $300 - SOLD got this as a shell w/out engine or clip. made it into and aspheric, that has a beam similar to a McGizmo Sundrop
Used a Qlite 3.04A driver, and an XM-L2 from Mountain Electronics. drilled a blank pill for wires coming through away from center so the led had a place to set...
got an Aspheric Lens from ThorLabs, and used a blue o-ring I had laying around as the gasket.
For the spacer between the pill and the lens, I used a black rubber grommet.
Added one of Jeff's clips from his latest batch. much smoother and seems stiffer too.
Will also include the stock flat lense and oring, plus a stock Mac triple XP-G 2.8A engine.
Has use marks.
Sundrop left, TinyDC Right.
http://www.indysworld.com/flashlights/aspheric-1.jpg
http://www.indysworld.com/flashlights/aspheric-2.jpg
Exterior pics.
http://www.indysworld.com/sale/aspheric-tinydc-1.jpg
http://www.indysworld.com/sale/aspheric-tinydc-2.jpg
http:/www.indysworld.com/sale/aspheric-tinydc-3.jpg
http://www.indysworld.com/sale/aspheric-tinydc-4.jpg
Mac's Customs SST-50 EDC in Aluminum, Engraved. $300 - SOLD
No clip on this one, but I could tap it if needed. the tail has "Mac's Customs EDC" engraved around the outside, and there is plenty of room to place a clip too.
SST-50 engine has a neutral tint, and runs at 1.4A. 16340 Body. (I would not bore this one larger as the body walls would be too thin IMHO.)
http://www.indysworld.com/sale/macs-edc-engraved-1.jpg
http://www.indysworld.com/sale/macs-edc-engraved-2.jpg
http://www.indysworld.com/sale/macs-edc-engraved-3.jpg
http://www.indysworld.com/sale/sale-group.jpg
No batteries included. Shipping included in USA, if outside, PM.
Mac's Customs SST-50 Knurly in Aluminum: the very first Mac's knurly. $425 - SOLD $500 $525 $550 $600
Original thread: http://www.candlepowerforums.com/vb/showthread.php?246903-quot-Knurly-quot-SST-50
In my knurly quest, I traced it through owners, and aquired it... as some point, the engine was modified for higher output.
This is the same length as the first run EDC lights that used a shorter reflector. it currently has in it my triple conversion pill (which I had to shorten to fit), running a Qlite 3.05A driver with 3-up XP-L from MtnElectronics.
Will include the original single emitter engine.
16340 body, but could be bored for 18350.
http://www.indysworld.com/sale/first-knurly-1.jpg
http://www.indysworld.com/sale/first-knurly-2.jpg
http://www.indysworld.com/sale/first-knurly-3.jpg
http://www.indysworld.com/sale/first-knurly-4.jpg
http://www.indysworld.com/sale/first-knurly-5.jpg
http://www.indysworld.com/sale/first-knurly-6.jpg
Sinner Copper 18350 Host for laser. $125 - SPF .$150
laser module is non-working. I was going to make a flashlight head for this, but need funds for something else instead... new laser modules for this can be found here:
https://sites.google.com/site/dtrlpf/home/diodes/bdr-209-405nm-16x-diodes
http://www.indysworld.com/sale/sinner-laser-host.jpg
http://www.indysworld.com/sale/sinner-laser-host-2.jpg
Tain Aura Damascus . $700 - SOLD .
stainless damascus. uses 14500 Battery. Ice Blue Trits around tail, red trits in switch. Includes Gamblemade Mokume Gane dangler as shown.
http://www.indysworld.com/sale/Tain-Dam-1.jpg
http://www.indysworld.com/sale/Tain-Dam-2.jpg
Sigma Customs Brass 18650 with Mr. Bulk Big Bulkhead Turbo Head with VoB engine. $450 - SOLD .
BratGuy Ti boot retaining ring, blasted to match.
VoB (Adventure Sport) engine is XP-L HI single emitter.
Sigma Engine: -Nichia 219C D280 5000k 80+ CRI Triple, 3.04A Qlite w/guppydrv, frosted optic, AR lens
http://www.indysworld.com/sale/Sigma-Bulk-1.jpg
http://www.indysworld.com/sale/Sigma-Bulk-2.jpg
Aspheric Okluma TinyDC in Aluminum. $300 - SOLD got this as a shell w/out engine or clip. made it into and aspheric, that has a beam similar to a McGizmo Sundrop
Used a Qlite 3.04A driver, and an XM-L2 from Mountain Electronics. drilled a blank pill for wires coming through away from center so the led had a place to set...
got an Aspheric Lens from ThorLabs, and used a blue o-ring I had laying around as the gasket.
For the spacer between the pill and the lens, I used a black rubber grommet.
Added one of Jeff's clips from his latest batch. much smoother and seems stiffer too.
Will also include the stock flat lense and oring, plus a stock Mac triple XP-G 2.8A engine.
Has use marks.
Sundrop left, TinyDC Right.
http://www.indysworld.com/flashlights/aspheric-1.jpg
http://www.indysworld.com/flashlights/aspheric-2.jpg
Exterior pics.
http://www.indysworld.com/sale/aspheric-tinydc-1.jpg
http://www.indysworld.com/sale/aspheric-tinydc-2.jpg
http:/www.indysworld.com/sale/aspheric-tinydc-3.jpg
http://www.indysworld.com/sale/aspheric-tinydc-4.jpg
Mac's Customs SST-50 EDC in Aluminum, Engraved. $300 - SOLD
No clip on this one, but I could tap it if needed. the tail has "Mac's Customs EDC" engraved around the outside, and there is plenty of room to place a clip too.
SST-50 engine has a neutral tint, and runs at 1.4A. 16340 Body. (I would not bore this one larger as the body walls would be too thin IMHO.)
http://www.indysworld.com/sale/macs-edc-engraved-1.jpg
http://www.indysworld.com/sale/macs-edc-engraved-2.jpg
http://www.indysworld.com/sale/macs-edc-engraved-3.jpg
Last edited: