ArmyTek        
Page 1 of 2 12 LastLast
Results 1 to 30 of 54

Thread: FS: Brat Guy (McBrat) Lights

  1. #1

    Default FS: Lights from Brat Guy Enterprises

    This will be my running sales thread for lights as I make and sell them....

    Currently Available Lights:


    Nickel Silver Deuce Mule CR2 Deuce Mule 15270/CR2 nickel silver. Custom short Ti clip.
    Light was originally designed for 18350 until i had an issue with machining and had to shorten the body so has a delrin spacer to fit the 15270.
    Engine is 105C 2.8A, pushing a Nichia 219b sw45 R9080, and can run lower modes on cr2. (test engine is pictured)
    $250 shipped USA. Add $20 shipping outside USA.




    Sintered Bronze Deuce. Ti clip, heat colored. McClicky and Ti boot ring.
    Buyer has choice of engine:

    1. SST-20 single emitter engine with H17Fx driver, built by Devin at Sigma Customs.
    2. SOYCD triple 219b w/105c driver.
    3. Aspheric lens and single emitter engine with driver options.

    Last pic shown with a brass and copper (neither for sale) to try and show the color.
    withdrawn.




    ***** SOLD Lights below this line *****

    SOLD Nickel Silver Deuce 18350 with tail flutes and tail crenelations. Amber Dragon with Nichia 5000k 219C primaries. McClicky switch and Ti boot ring. Mineral glass. Alien v2 Ti clip w/Ti screws.
    SOLD - $400 shipped USA. Add $20 shipping outside USA.
    http://www.indysworld.com/sale/BGE-NS-Deuce-1.jpg
    http://www.indysworld.com/sale/BGE-NS-Deuce-2.jpg
    http://www.indysworld.com/sale/BGE-NS-Deuce-3.jpg
    http://www.indysworld.com/sale/BGE-NS-Deuce-4.jpg
    http://www.indysworld.com/sale/BGE-NS-Deuce-5.jpg

    SOLD $400 Copper Deuce 18350
    C145 Copper
    2mm mineral glass lens
    Copper pill with HMW XP-G2 guppydrv engine
    Drilled optics with blue luminous devices and green glow pad
    McClicky switch
    copper boot ring
    Ti star clip w/Ti 4-40 screws

    Price is shipped in usa:
    Shipping outside of USA, please add $15.

    http://www.indysworld.com/sale/copper-deuce-1-1.jpg
    http://www.indysworld.com/sale/copper-deuce-1-2.jpg
    http://www.indysworld.com/sale/copper-deuce-1-3.jpg

    earlier pics
    http://www.indysworld.com/sale/Deuce-Copper-Star-1.jpg
    http://www.indysworld.com/sale/Deuce-Copper-Star-2.jpg
    http://www.indysworld.com/sale/Deuce-Copper-Star-3.jpg


    SOLD : 18350 in 3 color Mokume. Brass, Copper, Nickel Silver.

    New Engine: XM-L2 U4 1A LED on 14mm MCPCB
    Approximate light output: 1268 - 1344 lumens @3A; 25 degrees celsius
    Color temperature: 6500-7000K (specs from MTN. doesn't seem that cool to me...)
    Brass had some impurities in it during forging process, so there are some tiny "craters" as shown in close up shots. none are through holes.
    Price is SOLD - $525 with Bearpaw clip (or other BratGuy clip) , and includes shipping.
    http://www.indysworld.com/sale/bge-mokume-rgbw-1.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-2.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-3.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-4.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-5.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-6.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-7.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-8.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-9.jpg
    http://www.indysworld.com/sale/bge-mokume-rgbw-10.jpg


    SOLD: Brat Guy 18650 Aspheric Copper

    18650 Copper Aspheric
    Qlite 3A driver w/guppydrv DUAL
    Nichia 319AT 5000k
    Copper pill
    McClicky switch
    Black Switch Boot
    Cooper Boot Ring
    Tumbled Ti Bear Paw Clip
    $499
    Pics show an XP-L HI, but the above engine is what's installed.

    Can also swap in the SOYCD XP-G2 4 Amp engine if desired. This light is compativble with other Mac/Trident/Hanko engine upgrades as well...

    http://www.indysworld.com/sale/bge-copper-18650-1.jpg
    http://www.indysworld.com/sale/bge-copper-18650-2.jpg
    http://www.indysworld.com/sale/bge-copper-18650-3.jpg
    http://www.indysworld.com/sale/bge-copper-18650-4.jpg


    FS: #12 Damascus 18650 SOLD - $750 shipped in CONUS. Elsewhere add $15 for shipping.

    1080 and 15N20 Hand Forged Twist Damascus
    uses 18650 battery (not included)
    triple Nichia 319AT - 5000k D440 70+ CRI on copper pill (Okluma, Mac, HMW Trident compatible)
    Qlite 3.04A driver with guppydrv
    McClicky switch
    2mm mineral glass lens
    Carclo 10507 optic with blue glow material in center from Joseph Thompson
    Black switch boot and Ti boot ring
    Brat Guy Ti Star clip
    Ti clip screws

    light is just a tad over 4-7/8" long.

    Also of note. The grooves are hard 90s, so it may be a pocket eater over time....

    http://www.indysworld.com/sale/bge-12b-1.jpg
    http://www.indysworld.com/sale/bge-12b-2.jpg
    http://www.indysworld.com/sale/bge-12b-3.jpg
    http://www.indysworld.com/sale/bge-12b-4.jpg
    http://www.indysworld.com/sale/bge-12b-5.jpg

    #13 6061 Aluminum 18350 SOLD - $250 CONUS. Elsewhere add $15 for shipping.
    18350 Aluminum
    triple Nichia 219A with 105c 2.8A 3 mode driver, on aluminum pill.
    Will also take Okluma DC1, Hanko Trident, Mac engines.
    Glow powder under posts of 10507 optic.
    Heat colored Ti clip with Ti screws.
    Switch in this one is a PCB forward clicky from MTN with a custom delrin boot spacer and aluminum boot retaining ring.
    I made a copper adapter that allows a McClicky switch (not inclluded) to be dropped in as well.
    Bezel lip is beefy to protect the 2mm mineral glass lens.
    Light has a few marks on tail end as seen in photo.

    http://www.indysworld.com/sale/bge13b-1.jpg
    http://www.indysworld.com/sale/bge-13-3.jpg
    http://www.indysworld.com/sale/bge-13-4.jpg
    http://www.indysworld.com/sale/bge13b-2.jpg
    http://www.indysworld.com/sale/bge13b-3.jpg
    Last edited by mcbrat; 09-06-2019 at 04:37 PM.

  2. #2

    Default Re: FS: Brat Guy Enterprises Lights

    Reconfigured the Damascus light with reduced price.

  3. #3

  4. #4

    Default Re: FS: Brat Guy Enterprises Lights

    reworked the grip on #13. got rid of the milling, which I didn't like, and put on a similar design to my other lights.
    also, I made a copper adapter so you can drop in a McClicky switch as well (the PCB switch is a lot heavier it seems)

  5. #5

    Default Re: FS: Brat Guy Enterprises Lights

    I'll take # 13
    Thanks, CPF!

  6. #6

    Default Re: FS: Brat Guy Enterprises Lights

    Thanks, CPF!

  7. #7

    Default Re: FS: Brat Guy Enterprises Lights

    added aluminum 18650 triple 219BT

  8. #8

  9. #9

    Default Re: FS: Brat Guy Enterprises Lights

    #13 looks great, just want to stop by and say that

  10. #10
    Honorary Aussie
    Join Date
    Feb 2014
    Location
    USA
    Posts
    4,985

    Default Re: FS: Brat Guy Enterprises Lights

    Very nice Dams for sure. Luv the washer style design. Both aesthetically pleasing and very tactile as well.
    It is better to buy a beautiful, expensive, custom flashlight than to curse the darkness.

  11. #11

    Default Re: FS: Brat Guy Enterprises Lights

    remaining lights from my recent set are up in the first post.....

  12. #12

    Default Re: FS: Brat Guy Enterprises Lights

    I'll send you a PM

  13. #13

    Default Re: FS: Brat Guy Enterprises Lights

    Additional options with purchase of Mokume light:
    swap to XM-L 2.8A engine: -$100
    swap to XM-L2 2.8A engine: -$100
    swap to SST-50 Engine: -$100
    SteelFlame Silver Darkness Clip + $200

  14. #14
    Honorary Aussie
    Join Date
    Feb 2014
    Location
    USA
    Posts
    4,985

    Default Re: FS: Brat Guy Enterprises Lights

    The mokume is nice despite the pits.
    It is better to buy a beautiful, expensive, custom flashlight than to curse the darkness.

  15. #15

  16. #16

  17. #17

  18. #18

    Default Re: FS: Brat Guy Enterprises Lights

    let me know if any questions.....

  19. #19

    Default Re: FS: Brat Guy Enterprises Lights

    Only mokume remains from this last group.

  20. #20

    Default Re: FS: Brat Guy Enterprises Lights

    Switched up the configuration of the mokume along with the price.....

  21. #21

    Default Re: FS: Brat Guy Enterprises Lights

    Would also potentially trade for a Mac...

  22. #22

  23. #23

  24. #24

  25. #25

  26. #26

    Default Re: FS: Brat Guy (McBrat) Lights

    put a new engine in the light!

    New Engine: XM-L2 U4 1A LED on 14mm MCPCB
    Approximate light output: 1268 - 1344 lumens @3A; 25 degrees celsius
    Color temperature: 6500-7000K (specs from MTN. doesn't seem that cool to me...)

  27. #27

  28. #28

    Default Re: FS: Brat Guy (McBrat) Lights

    Added price option without the SF clip....

  29. #29

  30. #30

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •