4sevens
Flashlight Enthusiast
TNC\'s AA modded to 1000ma !!! *PICTS*
Hi everybody,
I have one of TNC's AA lights modded to DD a TV1K with
a AA Li-ion. TNC's AA's are a work of art. I've never
seen such attention to detail - I can't find any variations
in CNC'd aluminum. BEAUTIFUL.
But stinky me, I had to mod this little guy.
Similar to what did to the ARC-AA-Mega and the UltraGLux3
HERE
I did the same to the TNC AA except for the two/three stage switch.
(I have to find a way to put a good switch w/ resistors in this tight
area)
From a full charge (4.2v) it draws a whopping 1200ma !!!
You figure how much light it's putting out!
30 minutes later, it reaches 3.3v drawing about 600ma.
As long as I keep it in my hands or in a cup of water it's okay.
Sitting on the table and at full charge, it reaches 150F in about 1 minute. But about 10 minutes into the discharge, if left on the table
it will take about 3 minutes to reach that temp. However, in my hot
little hands, the temperature is kept below 150F. (Although the
first 2 minutes I have to switch hands every minute)
As long as it's in my hands, this little thing will put out lots of
lumens!
Here are some picts and beamshots (for your viewing pleasure)
compared with:
a stock Arc AA (yes, no fair here)
a Streamlight Jr modded with a TXOK, SO17XA, boosted to 800mah @battery
and also an Arc4+ first rev1
Left to right: Stock Arc AA, modded Strm Jr, Arc4+, TNC-AA-modded
at 1 feet
Same, but with exposure correction. Notice the side spill is much
more than the arc4+
This time just the the Arc4+(left) and the TNCAA mod(right) to duke
it out and 1 Meter.
Same with exposure correction.
Here they are standing on their ends (the Arc AA is not stock here -
it's modded with li-ion driven at 200mah) (The arc4+ is on it's end
thanks to Cy's tailcap mod 1.2) /ubbthreads/images/graemlins/smile.gif
Here's a bunch more with a nice Kroll at the end.
There are couple more picts plus you can click to get 3 megapix
of this picts HERE
What do you all think? When I add a two stage switch here it'll
be my serious EDC. /ubbthreads/images/graemlins/smile.gif Too bad it's not HA3 though.
David
/ubbthreads/images/graemlins/thumbsup.gif
Hi everybody,
I have one of TNC's AA lights modded to DD a TV1K with
a AA Li-ion. TNC's AA's are a work of art. I've never
seen such attention to detail - I can't find any variations
in CNC'd aluminum. BEAUTIFUL.
But stinky me, I had to mod this little guy.
Similar to what did to the ARC-AA-Mega and the UltraGLux3
HERE
I did the same to the TNC AA except for the two/three stage switch.
(I have to find a way to put a good switch w/ resistors in this tight
area)
From a full charge (4.2v) it draws a whopping 1200ma !!!
You figure how much light it's putting out!
30 minutes later, it reaches 3.3v drawing about 600ma.
As long as I keep it in my hands or in a cup of water it's okay.
Sitting on the table and at full charge, it reaches 150F in about 1 minute. But about 10 minutes into the discharge, if left on the table
it will take about 3 minutes to reach that temp. However, in my hot
little hands, the temperature is kept below 150F. (Although the
first 2 minutes I have to switch hands every minute)
As long as it's in my hands, this little thing will put out lots of
lumens!
Here are some picts and beamshots (for your viewing pleasure)
compared with:
a stock Arc AA (yes, no fair here)
a Streamlight Jr modded with a TXOK, SO17XA, boosted to 800mah @battery
and also an Arc4+ first rev1
Left to right: Stock Arc AA, modded Strm Jr, Arc4+, TNC-AA-modded
at 1 feet
Same, but with exposure correction. Notice the side spill is much
more than the arc4+
This time just the the Arc4+(left) and the TNCAA mod(right) to duke
it out and 1 Meter.
Same with exposure correction.
Here they are standing on their ends (the Arc AA is not stock here -
it's modded with li-ion driven at 200mah) (The arc4+ is on it's end
thanks to Cy's tailcap mod 1.2) /ubbthreads/images/graemlins/smile.gif
Here's a bunch more with a nice Kroll at the end.
There are couple more picts plus you can click to get 3 megapix
of this picts HERE
What do you all think? When I add a two stage switch here it'll
be my serious EDC. /ubbthreads/images/graemlins/smile.gif Too bad it's not HA3 though.
David
/ubbthreads/images/graemlins/thumbsup.gif