Recent content by Baulz

fenix-store
  1. B

    Cable Switch on Handlebar Experiences?

    I use a Judco switch from digikey on my bar, just use a piece of velcro to hold it in place. Nothing fancy but it works.
  2. B

    why hasnt any one made a p60 / 18650 batery box

    No, Ontario Canada. Are we both from Peterborough, but different countries?
  3. B

    why hasnt any one made a p60 / 18650 batery box

    Sounds a lot like a flashlight.
  4. B

    35mm Reflector

    Do they have to be modified to fit a P7? I thought the were for smaller LED's.
  5. B

    Found the new Sony LSD batteries at Canadian tire

    I bought the PC charger/4AA combo yesterday. The back of the charger has Sanyo molded into it, and had the PC logo printed on the front.
  6. B

    DIY "Super" taillight (concepting stage)

    But the Vf is much lower on the red crees so I thought it would take a specific driver. Will any work as long as the output current is in a safe range?
  7. B

    Rear Red LED vs rear filtered White.

    Any suggestions on a driver with flashing mode for the red Cree's? Looked around at DX and could not find anything suitable.
  8. B

    hipFlex

    :popcorn: Been watching this thread for a while, can't wait for the hipflex to be ready.... Trying to decide the best way for me to use one, all my Li-Ion battery packs are 7.4v. Will I be able to run 2 P7's on the hipflex? As long as the LED's have a Vf of 3.5v or less I should be fine...
  9. B

    Problem with KD Super P7 Driver

    I'm using a 7.4v Li-ion pack. The board is now inside my light housing, the only way now to check how hot it gets is to take the entire thing apart, which will not be easy due to the amount of epoxy holding it all together. The shutting off is just so random, I can't figure it out. It just...
  10. B

    Problem with KD Super P7 Driver

    I built a P7 helmet light using a KD Super Output SSC P7 LED Driver Board . It worked great at first, a fantastic light. - Then the multi-mode stopped working, the light is stuck on high. I was able to change it a few times, but have not been able to for over a week now. - The light now...
  11. B

    Most simple (to build) P7 Helmet light

    I have been strruggling to find a way to build a P7 lights using the same reflector, and really like what you have done. My goal was a nice looking light, but going to go with your easy functional design. Thanks for sharing!:)
  12. B

    18650 battery holder does it exist?

    From reading on here and other forums it seems there are lots of people looking for holders, but none have been found yet. I've been thinking about just modifying some AA holders to work, but need the cells held tightly in place so I doubt it would work for me.
  13. B

    How do poeple waterproof their batteries?

    LeeValley also sells it in Canada, but I can't find it on their website right now...
  14. B

    Best housing for P4 and 20 mm optic?

    Solder :thumbsup: If you go to a Home Depot or similar store they will have it in the same area as the copper caps. Make sure you buy some flux too, and extra caps for practise.
  15. B

    Best housing for P4 and 20 mm optic?

    I've built lights with the 3/4" copper fitting and they work well, plus it's fun to get out the propane torch to assemble a few fittings together. :D The optics I used were a tiny bit too big to fit, a few minutes with a file fixed that.
See more

Latest posts

Top