Show your lights with trits!

[root_console]

These all look great. I am going to have to look into this. At least a lanyard with a trit...

 

[supersuby]

How was this done?

Was the head drilled out and the trits slid in the holes?

What size trits? 1.5x6mm? Same as the ones in the tail switch?

+1 Who did the trit mod for you? I have a couple v10r's i would like to have trits added to

 

[supersuby]

Toby i love the spy with the Blue Trits :thumbsup: But what is the light on the right with the 2 green trits and green glow ring?

 

[juplin]

+1 Who did the trit mod for you? I have a couple v10r's i would like to have trits added to

Please refer to the thread below:
http://www.cpfmarketplace.com/mp/sh...10R-titanium-18650-18500-and-tritium-switches
The modding in the head is able to be done only if the head can be dismantled, that should be mentioned by kuku427 in the recent posts of that thread.

 

[calipsoii]

Simple, yet effective.

 

[Titanium81]

Very nice picture! I love the Blue and Green Trits.

Liteflux LF2XT, Whetstone EX10, Sunspot D10, and Citizen Eco.

 

[toby_pra]

Toby i love the spy with the Blue Trits :thumbsup: But what is the light on the right with the 2 green trits and green glow ring?

Thats an Aleph Mule, two trits installed around the led

 

[toby_pra]

 

[Titanium81]

Are these blue or ice-blue tritium vials? Also how far away is the tritium visible? (in total darkness)

 

[toby_pra]

I dont know how far this cant bee seen...

Jepp thats iceblue

 

[Titanium81]

Really? That's Awesome! I always thought blue was a lot dimmer. Maybe the Ice-Blue is significantly brighter.

I dont know how far this cant bee seen...

Jepp thats iceblue

 

[thevinstigator]

Seems like everybody is doing thisd themselves, is anybody doing the milling here comercially?? Seems like alot of people want to get this done on their lights, including me :ironic:. Awesome lights with the sticks installed. Thanks for sharing.

 

[Cogitria]

Not really a light, but I like the pic, so here you go.

Totally agree! like decoration

 

[precisionworks]

is anybody doing the milling here commercially??

Here are some that I've done and more lights are currently in process ...

McGizmo Ti Haiku being milled:

NiteCore piston being machined:

Added a 50,000 rpm air spindle specifically for aluminum slot milling & installed a digital readout:

Machining a slot for a 1.5x5mm trit on each side of an M3

Green trit dry installed to check sizing

An L5 with three trits located at 120° spacing, one directly opposite the clip:

An L1 with two trits spaced 180° apart. Just barely enough room to drop the slot into the tiny groove behind the checkering:

And an A2 with three trits at 120° spacing ... and an even smaller space to land the end mill

 

[rockingthe2]

Here's the only one I have:

Sunwayman V10R Ti with Steve Ku trit switch.

 

[torino]

:naughty:
Uploaded with ImageShack.us
:naughty:

 

[JMP]

Where the trits at torino? All I see are glow rings. Those are not even close.

 

[Miri]

Nice trits! But I guess it´s too difficult to get some over here in Europe.

And nice work, precisionworks! Interesting to see how the trit chambers are made.

 

[torino]

no dont have the trit yet but this looks nice also :laughing:

 

[HKJ]

Nice trits! But I guess it´s too difficult to get some over here in Europe.

Why would it be that? One of the cpf trit sellers live in Europe?