RofisLight        
Page 1 of 35 1234567811 ... LastLast
Results 1 to 30 of 1033

Thread: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

  1. #1

    Default P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    PART 11 !!! P60 Style Custom Drop - in modules for SF and other Products. (part 10 can be found here)

    Here I am offering P60 Style drop ins, they are available with Leds from the following manufacturers with some of the leds that will be offered are below.

    SSC Seoul - P7 , P4
    Cree -
    XML2 , XPG, XP-E, MC-E, XRE , UV, are available here many in warm , neutral or cool white
    Osram - Platinum Dragon IR/ Hyper-red
    Luminus - SST -50, SST -90


    These modules will fit most flashlights that accepts a standard P60/D26 Style module. They will fit Surefire C and P style hosts and all Solarforce hosts that take P60 modules. They also fit a variety of other manufacturers such as trustfire , ultrafire to name a couple

    THESE DO NOT FIT OLD STYLE G2 HOSTS ( very old ) they will fit G2L's


    __________________________________________________ ___________________________

    Here are a couple of pictures of reflectors used. These are designed for XPG/ XPG-2 and such

    Textured


    Smooth



    The XML reflectors are basically the same just with a larger center hole.


    All of the modules end up being as close to standard length as possible The large die leds are much thicker and there is a small possibility that there will be a crack at the head and body. I keep all as short as possible so if there is a crack there is probably nothing that can be done.

    All hosts are slightly different and one module may fit tight in a SF product and a bit loose in a FM Nite clone or an FM C but they will fit all. One may need to have the spring cut down to allow the head to close or a whole spring may be needed to keep the module from rattling. They also fit most Solarforce or any P60 style host

    Please state if using in a FM Cooly , 2P maglite and such.


    Most LED's are carried in Cool White, Neutral White, or Warm white when possible. They will be listed if in stock if not listed probably not in stock.

    Battery configs listed are for any battery that falls into the range listed. Yes 2XCR123 will work in a 6 volt max config.

    Potting is the filling of electronics cavity with thermal epoxy for heat management and shock protection. Copper tape is included with potting and both are included at no charge unless specified by member that they do not want this option.

    ALL MODULES ARE LEAD FREE, ALL SOLDER USED IS LEAD FREE

    __________________________________________________ ___________________________


    WE NOW ARE MOUNTING ALL XPG2, XML2, NICHIA EMITTERS ON ALL COPPER DIRECT BOND SINKPADS
    EMITTERS CARRIED

    __________________________________________________ _______________________

    CREE LEDS
    http://www.cree.com/products/xlamp.asp binning and tint information (GREAT RESOURCE) Look under documentation on specific type emitter

    Cree XM-L2
    $40

    U2 flux 6500k tint
    T6 flux 5000k tint
    T5 flux 4500k tint
    T4 flux 4000k 5B4 tint
    S6 flux 3000k tint 90+ CRI

    Driver choices are below.


    Direct drive
    1 Level only (potting and tape included this model only)
    works well in the 26650 Cooly's by Five Mega. Not made for continuous run.
    __________________________________________________ ______________________________________

    1 level 2.2 amps 3.6-16 volts best for use with Multiple cells.
    __________________________________________________ ______________________________________

    Available levels with memory (2.8-6 volts only) 3amp stock setting all regulated
    1 level - high Regulated
    2 Low / High
    3 level - Low / Med / High Regulated (5%- 30%-100%)

    6 volt Drivers are 3 amps stock


    Either Smooth OR Op reflectors available (extra reflectors on website.)
    __________________________________________________

    The new XPG-2 modules are located in this thread
    HERE


    Cree XP-G -$35 *mixture of throw and flood*
    2.8-6 (levels are 100% / 40% / 5% )

    5 level low / med / high/ SOS / Strobe with memory available in 1.4 amp
    4 level starlight / low / med / high 1.5 amps
    3 level low / med / high 2.8-6 volts with memory available in 1.4 amp
    1 level 2.8-6 volts

    1 Level 4-14 volts / 1.5 amp

    Flux Bins and tints that are available for XPG


    Q23000K 7A3 (90 minimum CRI) NEW
    Q4 2900k 8A4 tint
    R4 4000k 5B3 tint /5B2
    R4 5000k 3C tint
    R5 5500k
    - 2T tints (Cool White comparable to WH tint)
    S2 6300k - 1T tints (coolwhite comparable to WF tint)


    DUAL XPG (Linger Special)$45 Any of the above bins are possible / 3 amp 2.8-6 volts max *Floody* (levels available are same as XML) some center clutter is visible in beam

    DBS MODULES AVAILABLE ON REQUEST for most emitters / brass pill only no reflector/ same price as regular modules, potting is included on these also.
    __________________________________________________ ______________________
    TWO NEW NICHIA 219B

    Nichia CRI92 NVSL219B- R85 B220 4500k 90 CRI neutral ($35)
    Nichia NVSL219B 90 CRI 5015K neutral ($35)


    Driver Levels the same as the XPG's above

    __________________________________________________ ________________________

    Cree XRE - XPE -$30 -
    1.5 amp with memory
    2.8 - 6 volts 3 level regulated Low/ med / high
    2.8-6 volts 5 levels regulated - high / med / low / SOS/ strobe
    2.8-6 volts 4 level regulated starlight / low / med / high

    3.6 -16V regulated @ 1.4 amps - 1 levels

    XPE Good Throw
    R2 or R3
    available coolwhite / (Q3 5B)
    neutral /warm tints
    XPE Green , real Red, Amber /Blue

    XRE (Good Throw )
    R2 flux WF tint
    Q45B neutral
    8E7 warm white
    Green/ blue/ royale blue colors

    Smooth OR OP reflectors are available

    Optics are for XRE emitters only
    / Cool white , neutral white and warm whites.
    8degree/ 60 degree.
    $37 for module and 1 optic $40 with 2 optics
    __________________________________________________ _________________________

    Cree MCE $ 50 - GOOD FLOOD

    1 - 3 or 5 level regulated
    2.8 - 6 volts

    Cool - M bin WD, WG
    Cool - Nbin no tint supplied but pure white
    Neutral - Kbin 5B tint
    Warm bins JE5, JE6, KA3
    __________________________________________________

    LUMINUS SST SERIES LEDS

    Luminus SST-50 - $55 -

    2.8 -6volts only *good throw with adequate spill*

    direct drive
    1 Level direct drive

    Regulated with memory offered with same amperages as XML's listed above
    1 level
    3 level -- Low - Med - high
    3 level -- low- high- strobe


    Flux Bins are

    6500K Cool White
    (W65S-GJ102-WJ-G4 )
    5700k (w57S-GJ201-WJ-H4 )
    4500k (w45S-GJ400-WJ-P3 )

    Luminus SST -90 -$70 -

    2.8 -6 volts only *Floody*

    1 Levels direct drive or regulated drivers with memory with the same amperage drivers used with XML's above and same levels

    6500 (W65S-WN-G3 )
    5700k (W57S-WN-H4)

    Green - Red
    - Blue Colered SST90's also available
    __________________________________________________ _________________________

    __________________________________________________ _________________________

    OSRAM IR LEDS

    Osram Oslon Black IR $40 (850 940nm)-2.8v- 6 volts /1 level / 3 level - 2.8-6 volts
    Generic Quad Die 10watt IR great for night pictures

    __________________________________________________ _________________________


    I try to keep the above listed led's in stock, I also try to keep the newest and most popular bins and color temps from cool whites / neutrals / and warm white and high CRI models.

    Now as to levels in drivers , most of the time the levels are fixed and can't be changed. As new drivers become available the offerings will change on this page so please check it first. I often will have to change depending on what drivers I have available to me at the time so please check this page and I will update as needed.

    Please specify what host and batts you are using when inquiring about a module or led. Just remember if you don't see it or don't understand something just write as I don't mind helping but check this page first. These are not try and buy ask if you don't understand!

    Now that said the search button for this forum has a wealth of knowledge, much more than I can ever remember and usually with in days of a new led release runtimes and lumens are often posted please check the forum's search box as it is invaluable.


    When ordering please post your order in this thread plus put details in Paypal notes of what emitter and tint ordered/ include choice of reflector / # of levels / check to see if shipping address is visible . Also please list CPF Nickname in paypal notes.

    Shipping is 3 working days Although next day is not unusual Shipping confirmations are sent from Stamps.com when mailed


    Make sure your address in paypal is correct becuase that IS WHERE IT WILL BE SENT.

    If you want it mailed to an alternate address
    from the paypal address please state I want my parcel sent to an alternate address if this is not done I will think it is a duplicate address and will send to what is listed on PP.

    MY Paypal info in biography or PM for it / I do not send confirmations that I received your paypal if it is properly addressed then I WILL receive it, you should be receiving a receipt from paypal when sent if configured properly

    1st class shipping is included CONUS
    Domestic Priority is $5 for up to 4 modules

    International shipping
    is $12 for 1st class Int up to 3 modules , Priority Mail Int. is $23.95 up to 8 modules , express mail and more than 8 modules quoted.


    Beam shots are posted below and new products will be posted below. Please send your beam shots and I will try to list when possible or create a link to them.

    New offerings will be listed below as they become available under news.

    XPG-2 modules can be found here

    90 CRI XML modules can be found here

    D36 for M STYLE and M to C lights are (HERE)
    __________________________________________________ ___________________________________

    IN NEED OF A HOST THEN HERE ARE SOME GREAT FORUM MEMBERS THAT CAN HELP

    Here on BST Five Mega hosts are some of my favorites and here is the new coolys

    On marketplace get Fivemega 18mm Bodies in Multiple Sizes from Wonderlite and Jason will take good care of you.

    For milling of maglites and general millwork Will Quiles is the master and can be found (HERE)

  2. #2

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Reserved

  3. #3

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    This is where I will post news of new emitters / drivers and such.


    11/9/2012

    New U3 flux 1C modules now available.

    Also there are no 3C 5000k they are now 3B's and according to the packing slip they are U2 flux even though I ordered T6's they will routinely upgrade when new product arrives. I will check lumens a bit later.

    I also have new drivers that are stock 3 amps check above for the new levels.

    thanks

    Dave

    __________________________________________________ __________________

  4. #4

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    any update on the black oslon ir please, or do i look elsewhere?

  5. #5

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nobbybonez View Post
    any update on the black oslon ir please, or do i look elsewhere?

    Hi

    I had to get rid of the 100 bucks worth of platinum dragons that few asked for asked for and that I ordered before these came to light. Now I hate getting stuck with emitters so I limit new emitters but I have now sold a few of the platinum dragon so I have a couple of the oslons they are $40 smooth or op. 1 or 3 levels.

    Dave

  6. #6
    Flashaholic* psychbeat's Avatar
    Join Date
    Nov 2009
    Location
    SF norcal
    Posts
    2,792

    Default P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Hey Dave-
    Do u think u will ever have the 2mode XML drivers in stock again?

    Don't need anything ATM but am thinking a Linger w XPG2 neutrals would be pretty bright as a flood.

  7. #7

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by psychbeat View Post
    Hey Dave-
    Do u think u will ever have the 2mode XML drivers in stock again?

    Don't need anything ATM but am thinking a Linger w XPG2 neutrals would be pretty bright as a flood.
    Hi

    No promises, my vendor has changed manufacturers and I am quite impressed with the quality of the drivers. Just don't know at this time. If enough call for it I may find a different source for it.

    Dave

  8. #8
    Flashaholic* tobrien's Avatar
    Join Date
    Dec 2005
    Location
    Georgia Highway 441
    Posts
    4,861

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    NB, I'm in the process of hunting down a yellow fluorescent Surefire G3 body in the MP and i plan on putting two 17500 Li-ions in it. That being said, this light I'd likely keep in the car.

    do you think I should do a T40 flux bin 5B3 4000k neutral white on a 1 level 2.2 amps 3.6-16 volts driver?

    alternately, do you think I should scrap that idea and get a 3 level .8v-3 volts for low voltage for A / AA lights and put two AAs in the G3 body powering a Nichia 219?

    apparently I can use the metal Z44 bezels on the G3 so that should aid in heat management if I went for a 2.2 amp XM-L, but I'm tempted by the low voltage idea, too.

    do you have experience or knowledge from customers' using a similar setup on what most people do that you've seen?

    I realize the XM-L at 2.2A will put out a whole ton more light and this may be an unfair comparison, but I'm assuming two AAs on a low voltage/draw driver like you offer will give potentially the same runtime as a low(er) amperage XM-L on two 1100 mAh Li-ions, I'd guess

    edit: I will say I'm leaning to the XM-L but that'd be a ton of light in a dark car cabin potentially
    aka Edgar Allan Bro, Brosama Bin Liftin, Walter Crunkite, Bro Namath, Teddy Brosevelt, and the Tomahawk Crunkmissile.
    my lights - review of PrecisionWorks - that's Gucci Mane in my avatar

  9. #9

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by tobrien View Post
    NB, I'm in the process of hunting down a yellow fluorescent Surefire G3 body in the MP and i plan on putting two 17500 Li-ions in it. That being said, this light I'd likely keep in the car.

    do you think I should do a T40 flux bin 5B3 4000k neutral white on a 1 level 2.2 amps 3.6-16 volts driver?

    alternately, do you think I should scrap that idea and get a 3 level .8v-3 volts for low voltage for A / AA lights and put two AAs in the G3 body powering a Nichia 219?

    apparently I can use the metal Z44 bezels on the G3 so that should aid in heat management if I went for a 2.2 amp XM-L, but I'm tempted by the low voltage idea, too.

    do you have experience or knowledge from customers' using a similar setup on what most people do that you've seen?

    I realize the XM-L at 2.2A will put out a whole ton more light and this may be an unfair comparison, but I'm assuming two AAs on a low voltage/draw driver like you offer will give potentially the same runtime as a low(er) amperage XM-L on two 1100 mAh Li-ions, I'd guess

    edit: I will say I'm leaning to the XM-L but that'd be a ton of light in a dark car cabin potentially
    HI

    Well just remember that if the li ions are 1100 mah that is what you need to figure runtime with since running li ions in series only adds voltage not capacity. So if you are running a XML @2.2 amps you will get 30 minutes runtime, where as you would get about 80 minutes with the nichia since most AA NIMH are around 2200 mah.

    Now another route might be to order a solarforce P1 emergency yellow host from my site and use 18650's in it and get 2 to 3 times the runtime. The solarforce P1's are metal inner body with a fiberglass coating and I carry that host in olive and yellow. With this host you can carry a 5 level Nichia if wanted with moonlight.

    Of course you may like the feel and length of a G3.

    Dave

  10. #10

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Hi All

    I have been using these new 3 amp drivers and I really like them. Between the U3 emitters that are about pure white and the 3 amps drivers the brightness has increased substantially. The nice thing about the 3 amp is that while brighter you don't get the instant drop off in lumens that you do when when using the XML's at higher amperage on 18650's.

    For those of you that like the 5 level 1.5 amp drivers I use with the XPG2's you will also like the new 5 level with moonlight level for XML's. It is very close to the same levels as the 1.5 amp version.

    Dave

  11. #11
    Enlightened
    Join Date
    Dec 2005
    Location
    San Diego
    Posts
    98

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    I'm interested in the Cree UV XL 7090. Will this LED light up tennis balls? I like to go hunting for tennis balls at night. $45 because I'm too cheap to buy new tennis balls :/

  12. #12

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by hawkz View Post
    I'm interested in the Cree UV XL 7090. Will this LED light up tennis balls? I like to go hunting for tennis balls at night. $45 because I'm too cheap to buy new tennis balls :/
    Hi

    I really don't know but I can check tonight and see if it does. It makes most items like that show up but I really have to check. I also will check the Blue XTE as it is much brighter and if it does tennis balls like it does hunter orange it would be the ticket. I put one together the other day and used it coming out of the woods I was amazed at the distance that my buddies hat shined, it looked like his head was on fire it was quite startling.
    I will check them both out.

    Dave

  13. #13
    Enlightened
    Join Date
    Dec 2005
    Location
    San Diego
    Posts
    98

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Oh Cool. Never heard of Blue XTE before. But if it lights tennis balls up better than the 7090, then I'm in for one.

  14. #14

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by hawkz View Post
    Oh Cool. Never heard of Blue XTE before. But if it lights tennis balls up better than the 7090, then I'm in for one.
    HI

    OK i did not have a tennis ball but did have a dog toy with the same covering also I did not have a 7090 built but had a 365nm ledgine built and it did light up the material but gives much less visible light and would be much harder to navigate. The royal blue XTE also lit up the material and I think did a better job as it is much brighter and since it has more visible light you can also navigate buy it. Either can be ran from a 18650 or primaries.

    Let me know what you think and if you have any other questions. By the way the XTE is one of the newer emitters from cree and is quite bright with the form factor of a XPG type emitter.

    Dave

  15. #15
    Enlightened
    Join Date
    Dec 2005
    Location
    San Diego
    Posts
    98

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Let's see....there are a few options, all of which are okay by me:
    1. I can wait for you to test both the 7090 and XTE it on a real tennis ball to see which lights up the tennis ball more (You can just power up the LED and hold the ball over it. No need to build a P60 module)
    2. What about building a "Linger special" with both 7090 and XTE? Is this a possibility and what would it cost? That'd be one BAMF light

  16. #16

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by hawkz View Post
    Let's see....there are a few options, all of which are okay by me:
    1. I can wait for you to test both the 7090 and XTE it on a real tennis ball to see which lights up the tennis ball more (You can just power up the LED and hold the ball over it. No need to build a P60 module)
    2. What about building a "Linger special" with both 7090 and XTE? Is this a possibility and what would it cost? That'd be one BAMF light
    Hi

    No it is not possible to combine a XRE style emitter with a XPG type emitter. The material that coats the dog toys is the same material as a tennis ball and the same yellow color. I can get a tennis ball to test but I can not give a time line on acquiring it as I live 25 to 30 minutes to a store that would carry them.

    Dave

  17. #17
    Enlightened
    Join Date
    Dec 2005
    Location
    San Diego
    Posts
    98

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Well, okay. If you're confident it's the same material, then let's do it. PM me how much I owe you including shipping for the XTE module.

  18. #18

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Hi Dave

    PP ID1VP15547AU897403K sent for the following.

    CREE XML P60 S6 flux 7A2 tint 3200k 90 cri
    3 lvl - L/M/H Regulated with memory
    2.8-6V 3A
    OP Reflector
    $40

    CREE XP-G2 P60 R5 flux 3D tint 5000k
    3 lvl - L/M/H Regulated with memory
    2.8-6V 1.4A
    Smooth Reflector
    $35

    NICHIA P60 4500k 92CRI neutral
    3 lvl - L/M/H Regulated with memory
    2.8-6V 1.4A
    OP Reflector
    $35

    Total modules: 3
    Total cost: $110

    I will be using the them with primaries in a Solarforce L2P. I was unable to state this in my PP message due to the length limit.

    Thanks


    Don
    Last edited by donscpoo; 11-15-2012 at 07:45 PM. Reason: typo

  19. #19

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by donscpoo View Post
    Hi Dave

    PP ID1VP15547AU897403K sent for the following.

    CREE XML P60 S6 flux 7A2 tint 3200k 90 cri
    3 lvl - L/M/H Regulated with memory
    2.8-6V 3A
    OP Reflector
    $40

    CREE XP-G2 P60 R5 flux 3D tint 5000k
    3 lvl - L/M/H Regulated with memory
    2.8-6V 1.4A
    Smooth Reflector
    $35

    NICHIA P60 4500k 92CRI neutral
    3 lvl - L/M/H Regulated with memory
    2.8-6V 1.4A
    OP Reflector
    $35

    Total modules: 3
    Total cost: $110

    I will be using the them with primaries in a Solarforce L2P. I was unable to state this in my PP message due to the length limit.

    Thanks


    Don
    Hi Don

    Modules have shipped

    Thanks

    Dave

  20. #20

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nailbender View Post
    Hi

    I had to get rid of the 100 bucks worth of platinum dragons that few asked for asked for and that I ordered before these came to light. Now I hate getting stuck with emitters so I limit new emitters but I have now sold a few of the platinum dragon so I have a couple of the oslons they are $40 smooth or op. 1 or 3 levels.

    Dave
    hi dave

    i'm looking to host this in a solarforce l2p, how best to power it please?
    i would be looking for op reflector left loose and int. shipping... $45 total?

    thx

    nobby

  21. #21

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nobbybonez View Post
    hi dave

    i'm looking to host this in a solarforce l2p, how best to power it please?
    i would be looking for op reflector left loose and int. shipping... $45 total?

    thx

    nobby
    HI

    If using a L2P I would use a 1X18650 setup so choose the 2.8-6 volt version. This is the most efficient set up.

    Price for module is $35 and $5 for 1st class Int.

    Dave

  22. #22

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nailbender View Post
    HI

    If using a L2P I would use a 1X18650 setup so choose the 2.8-6 volt version. This is the most efficient set up.

    Price for module is $35 and $5 for 1st class Int.

    Dave
    black oslon ir,
    2.8-6v,
    3 mode.
    OP reflector, do not threadlock please
    int shipping
    $40 sent
    pp id ID3R61661453190230D

    thankyou

  23. #23

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nobbybonez View Post
    black oslon ir,
    2.8-6v,
    3 mode.
    OP reflector, do not threadlock please
    int shipping
    $40 sent
    pp id ID3R61661453190230D

    thankyou
    Hi

    Got it will ship first of the week.

    For anymore of these ordered they are $40 not $35 as I looked at the invoice wrong and the are much more expensive than my XML's.

    Dave

  24. #24

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nailbender View Post
    Hi

    Got it will ship first of the week.

    For anymore of these ordered they are $40 not $35 as I looked at the invoice wrong and the are much more expensive than my XML's.

    Dave
    thanks for confirming receipt and honoring price quoted.
    don't leave yourself out of pocket, let me know if you need five dollah

    will report back with my findings for you, i'm sure a few more people will be wanting these...

    nobby

  25. #25

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nobbybonez View Post
    thanks for confirming receipt and honoring price quoted.
    don't leave yourself out of pocket, let me know if you need five dollah

    will report back with my findings for you, i'm sure a few more people will be wanting these...

    nobby
    Hi

    LOL no my mistake just don't want to make it twice.

    Dave

  26. #26
    Enlightened
    Join Date
    Nov 2008
    Location
    UK
    Posts
    42

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nailbender View Post
    Hi

    Got it will ship first of the week.

    For anymore of these ordered they are $40 not $35 as I looked at the invoice wrong and the are much more expensive than my XML's.

    Dave
    In the time it's taken to arrange the supply of these my needs have changed in that I currently need little or no IR illumination for my shooting rig. That's not a dig by the way Dave, it's just that I have made a dedicated NV rig in that time rather than an add-on one which needs stacks of IR compared to the one I have made.

    I may well decide to use an add-on rig again in the future and will wait until I have heard back from Nobbybonez with regard to the comparison between the Dragon IR you previously made for him and this new Oslon black one.

    This will be gobbledegook to some people reading it but an add-on NVD is added behind a day-scope, which has lens filters optimised for daytime wavelengths. Thus they filter out a lot of night time wavelength light. The rig I have made does away with the day-scope so my ikkle ebay special 1w 850nm drop-in IR module is more than enough for that rig.

    Looking forwards to your report on the NV shooting forums nobby.

  27. #27

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Quote Originally Posted by nobbybonez View Post
    thanks for confirming receipt and honoring price quoted.
    don't leave yourself out of pocket, let me know if you need five dollah

    will report back with my findings for you, i'm sure a few more people will be wanting these...

    nobby
    Hi

    Module shipped today

    Dave

  28. #28
    Flashaholic
    Join Date
    Nov 2012
    Location
    Munich/Germany
    Posts
    164

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XPG-2-XML-U3 / NICHIA 92CRI

    Hi,i orderedLuminus SSt-90 RED LEDsmooth reflector3 Amps 5 Modes Driver (1% - 5% - 25%-40% - 100%)int. shipping to GermanyPaypal sent. 3PY65416F0706912EHave a nice weekend!

  29. #29

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Hi Dave,

    I would like a

    P60 IR:
    Black Oslon IR,
    2.8-6v,
    1 level
    OP reflector
    potting
    $45 + Intl shipping $5
    PP sent 39H32575EE729980A
    Last edited by Red-T; 11-19-2012 at 04:16 AM. Reason: PP code added

  30. #30

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-XML-U3 / NICHIA 92CRI PART 11

    Quote Originally Posted by wertzius View Post
    Hi,i orderedLuminus SSt-90 RED LEDsmooth reflector3 Amps 5 Modes Driver (1% - 5% - 25%-40% - 100%)int. shipping to GermanyPaypal sent. 3PY65416F0706912EHave a nice weekend!
    Quote Originally Posted by Red-T View Post
    Hi Dave,

    I would like a

    P60 IR:
    Black Oslon IR,
    2.8-6v,
    1 level
    OP reflector
    potting
    $45 + Intl shipping $5
    PP sent 39H32575EE729980A
    Hi

    Both shipped

    thanks

    Dave

Page 1 of 35 1234567811 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •