nailbender
Flashlight Enthusiast
New Cree XP-G2 P60 Replacement Modules
This thread is for XP-G2 P60 modules. I decided to start a new thread for these new emitters from Cree since my regular P60 thread is a bit crowded. At this time I will only have Coolwhite.
I will be using a new XP-G reflector from a new manufacturer I have been using. These Lop and smooth are made for XP-G's type emitters. These are not the small hole design I have been using in my regular P60 thread. i have been using the new lop for all the nichia's I have been building and members have loved them. The lop finish is perfect in quality and makes a totally smooth ring free beam. The emitter hole is built for XP-G type emitters and they just work great.
For those that have not read up on these, they are brighter than the XP-G and should have much better throw. The XP-G has a 125 degree beam angle and the new XP-G2 will have a 115 degree beam angle much like the XP-E but much brighter. There are rumors of 400 lumens at 1.4 amps but we will have to see if this is true but several have quoted this. Since these run at 1.4 amps give or take that means we will have a good throwing emitter with pretty darn good runtimes.
I will get some pictures of the new emitter in the new reflector tomorrow as I get a few built. I will also post OTF lumens as soon as I get some built.
I hope in the near future to get some neutrals but at this time they are coolwhite only. I have found some neutrals and warms but the vendor will not bread any 1000 pc reels since they are so new and that is a few too many.
Prices will be the same as a regular XP-G so that means $35 a module shipping in the US is included.
Potting is included in the price
For International shipping the rates are as follows. Int 1st class is a added $12and Int priority mail is $23.95
ALL EMITTERS NOW MOUNTED ON DIRECT BOND COPPER SINKPADS.
Available voltages and levels and tints are below.
XP-G2 S2 flux 2B tint 6000k
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
2.8-6 volts 1.4 amps
1 level
3 levels * low, med, high *
3 levels * med, high , strobe* 1.5 amps only
5 levels *low, med, high, strobe, SOS*
with these 6 volt drivers I can add resistors to raise the amperage to 1.7 amps if wanted, that said remember the more amperage the more heat and the less runtime.
_____________________________________________________________________________
Low Voltage OUT OF STOCK
XP-G2 R5 flux 1D tint 6500k
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
Low voltage drivers .8-3volts
3 level (Hi 1.2 amp/ M - 50% / Lo 10%)
______________________________________________________________________
Multiple cells
XP-G2 S2 flux 2B tint
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
3.6-18 volts 1.75 amps
1 level
__________________________________________________________________________________________
XP-G2 S2 flux 2B tint
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
3.6-10 volts 1.4 amps
3 level *high, med, low*
_____________________________________________________________________________________
XP-E2 Emitters available in same options and levels available to XP-G2 above.
Price is $35
XP-E2 Coolwhite R3 flux 1C-1D tint
XP-E2 Neutral 4000k R2 flux 5B4 tint
XP-E2 Photo Red or red
XP-E2 Green
XTE Royal Blue
Rebel Cyan
_________________________________________________________________________________
Please include whether you want OP or Smooth reflectors.
Paypal is preferred payment method but money orders can be arranged. Paypal address is in my Bio. Please include CPF nickname, what ordered including voltage, levels, reflector type and if you want module potted in the paypal notes.
Please post what needed in thread including levels, reflector type and voltage.
Any questions please post in thread or PM me and I will get back to you.
Thanks
Here are a couple of pictures of the reflectors being used. They are the reflectors designed for XPG's
This thread is for XP-G2 P60 modules. I decided to start a new thread for these new emitters from Cree since my regular P60 thread is a bit crowded. At this time I will only have Coolwhite.
I will be using a new XP-G reflector from a new manufacturer I have been using. These Lop and smooth are made for XP-G's type emitters. These are not the small hole design I have been using in my regular P60 thread. i have been using the new lop for all the nichia's I have been building and members have loved them. The lop finish is perfect in quality and makes a totally smooth ring free beam. The emitter hole is built for XP-G type emitters and they just work great.
For those that have not read up on these, they are brighter than the XP-G and should have much better throw. The XP-G has a 125 degree beam angle and the new XP-G2 will have a 115 degree beam angle much like the XP-E but much brighter. There are rumors of 400 lumens at 1.4 amps but we will have to see if this is true but several have quoted this. Since these run at 1.4 amps give or take that means we will have a good throwing emitter with pretty darn good runtimes.
I will get some pictures of the new emitter in the new reflector tomorrow as I get a few built. I will also post OTF lumens as soon as I get some built.
I hope in the near future to get some neutrals but at this time they are coolwhite only. I have found some neutrals and warms but the vendor will not bread any 1000 pc reels since they are so new and that is a few too many.
Prices will be the same as a regular XP-G so that means $35 a module shipping in the US is included.
Potting is included in the price
For International shipping the rates are as follows. Int 1st class is a added $12and Int priority mail is $23.95
ALL EMITTERS NOW MOUNTED ON DIRECT BOND COPPER SINKPADS.
Available voltages and levels and tints are below.
XP-G2 S2 flux 2B tint 6000k
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
2.8-6 volts 1.4 amps
1 level
3 levels * low, med, high *
3 levels * med, high , strobe* 1.5 amps only
5 levels *low, med, high, strobe, SOS*
with these 6 volt drivers I can add resistors to raise the amperage to 1.7 amps if wanted, that said remember the more amperage the more heat and the less runtime.
_____________________________________________________________________________
Low Voltage OUT OF STOCK
XP-G2 R5 flux 1D tint 6500k
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
Low voltage drivers .8-3volts
3 level (Hi 1.2 amp/ M - 50% / Lo 10%)
______________________________________________________________________
Multiple cells
XP-G2 S2 flux 2B tint
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
3.6-18 volts 1.75 amps
1 level
__________________________________________________________________________________________
XP-G2 S2 flux 2B tint
XP-G2 R5 flux 3D tint 5000k
XP-G2 R4 flux 5B4 tint 4000k
XP-G2 R2 flux 7B4 tint 3100k warm white
XP-G2 Q2 7C1 tint 3000k warm white 90CRI
3.6-10 volts 1.4 amps
3 level *high, med, low*
_____________________________________________________________________________________
XP-E2 Emitters available in same options and levels available to XP-G2 above.
Price is $35
XP-E2 Coolwhite R3 flux 1C-1D tint
XP-E2 Neutral 4000k R2 flux 5B4 tint
XP-E2 Photo Red or red
XP-E2 Green
XTE Royal Blue
Rebel Cyan
_________________________________________________________________________________
Please include whether you want OP or Smooth reflectors.
Paypal is preferred payment method but money orders can be arranged. Paypal address is in my Bio. Please include CPF nickname, what ordered including voltage, levels, reflector type and if you want module potted in the paypal notes.
Please post what needed in thread including levels, reflector type and voltage.
Any questions please post in thread or PM me and I will get back to you.
Thanks
Here are a couple of pictures of the reflectors being used. They are the reflectors designed for XPG's
| |
Last edited: