Sold/Expired FS: Red Mag Shorty P7 0.9v-4.2v Driver, Forward Clickie Tailcap w/Led Glow

I have been asked about doing clickies in people's tailcaps...
I charge $40.00 to modify yours to a reverse clicky with a
single or 2-mode switch. The 2nd mode is for a resistor to
use the light on low.. Just let me know what resistor you
want to use, or send it to me with the End Cap.
In order for me to do this, i need "Your" Cap So you have
to send it to "ME" to modify. The battery spring is a custom
one like you see in the pictures below. If you have a spring
that you want me to use, just send it with the cap. Since i
am not using the stock spring perch where it makes contact
in the cap (the little un-anodized ring), I will be cutting down
any springs that are made to fit in that perch. I will solder
the spring to the switch directly, so there are no loose
connections to worry about. The whole assembly will have
to be epoxied in the cap, just like the picture. I dont have a
lathe to turn down the cap and do threads in there for a
removable switch cavity.. So the switch is permanently
installed, But the button "IS" removable for changing
The Quick-Clip is an extra option.. PM me for details.


I have here, A nice mod that i started awhile back..
But that thread dissapeared?

So without further Adoo:










Beamshots will be up later when the rain stops

Details:
Cutdown Mag 1D tube, Permanently fixed to the head
DX ROP Reflector
Glass Lens (Not UCL) <Replaced Now has an 52mm Optical
Glass lens from a DSLR Camera
DSWOJ P7
5-Mode Driver outputting 1300Ma-1400mA to the P7
Can run on ANY Battery from AAA-D, and Any LifePo/Li-Ion
You could even use the 3-4x Serial AA Adapters
An 18650/RCR123/CR123/AA Adapter Tubes included
24hr Green Glow around the P7
Led-Backlit Forward Clickie (works from 3v and up)
Quick-Clip w/2 keychain thingies

Ohh, The Driver/Heatsink Combo is fully removable
after you take off the lens/reflector.

The light output on a 1.2v/1.5v Cell is about 1/3 of a LifePo/Li-Ion

Did i forget something? I will think about it when i get
some beamshots up later :devil:

Price?
260.00US O.B.O. Open to a Trade
Shipping Conus Incl. Intl. Extra

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

That's a clean looking mag mod, Robert. Good luck with the sale, man!

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

That´s a nice sweet light.
Hope someday I can afford to have a top notch P7 Mag Mod like yours.
Regards.

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Bumpity bump!

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

You should sell these tailcaps alone for C and D mags!

:twothumbs

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Mail me yours, and i will modify it!

Sgt. LED said:

You should sell these tailcaps alone for C and D mags!

:twothumbs

Click to expand...

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

COOL

If it is of any importance my Mag is a 2D Mag 74 running on 7 Eneloops and uses the stock side switch oh and the tailspring will need to be a little stiff. So I suppose the main switch would have to be left on for the tail switch to work. Also, if the main stock is off would that control the tail glow like an on and off switch?

Because that would be sweet! Don't think I'd need the belt clippie, less work for you.

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Hi, great mod...

Can the flashlight use a different battery configuration to put 2.4ma to the Led?

How much can your charge to make this mod to the tailcap???

:twothumbs

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

PM sent

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Sgt. LED said:

COOL

If it is of any importance my Mag is a 2D Mag 74 running on 7 Eneloops and uses the stock side switch oh and the tailspring will need to be a little stiff. So I suppose the main switch would have to be left on for the tail switch to work. Also, if the main stock is off would that control the tail glow like an on and off switch?

Because that would be sweet! Don't think I'd need the belt clippie, less work for you.

Click to expand...

If the main switch is off, then nothing will work
If you wanted the main switch to control the light, then you will have
to turn on the tailswitch, thus turning off the little led behind the button.

I have lots of mag springs to play with :twothumbs so a "Stiff" one is doable
No clippie is okay But since i don't have any extra tailcaps, i need
yours

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Changchung said:

Hi, great mod...

Can the flashlight use a different battery configuration to put 2.4ma to the Led?

How much can your charge to make this mod to the tailcap???

:twothumbs

Click to expand...

I havent figured out a price yet..
And yes, you can use different configurations with
a 2.4mA backlit button, Within reason of course.
What kind of voltage range are you thinking?

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Sabrewolf said:

I havent figured out a price yet..
And yes, you can use different configurations with
a 2.4mA backlit button, Within reason of course.
What kind of voltage range are you thinking?

Click to expand...

I am not sure, maybe 3.6 x 3

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Changchung said:

I am not sure, maybe 3.6 x 3

Click to expand...

Thats not a problem

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Sabrewolf said:

Thats not a problem

Click to expand...

Hi again, if you dont sale it are you interested in a trade???

http://www.cpfmarketplace.com/mp/showthread.php?p=2242629#post2242629

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Changchung said:

Hi again, if you dont sale it are you interested in a trade???

http://www.cpfmarketplace.com/mp/showthread.php?p=2242629#post2242629

Click to expand...

To be honest, i dont wear a watch
And i allready have a Canon Rebel XTi
Gots anything else maybee?

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Sabrewolf said:

To be honest, i dont wear a watch
And i allready have a Canon Rebel XTi
Gots anything else maybee?

Click to expand...

What are you looking for? What will be a good trade for you?

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Changchung said:

What are you looking for? What will be a good trade for you?

Click to expand...

I dunno? where do you live?

If you live overseas.. Can i possibly obtain a
new gameboy ds with the Camera in it?
Maybe we can work something out?

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Sabrewolf said:

I dunno? where do you live?

If you live overseas.. Can i possibly obtain a
new gameboy ds with the Camera in it?
Maybe we can work something out?

Click to expand...

I leave in Venezuela, but, for security reason you should shipp the flashlight to USA Florida, then their send it to me... Can you show me a link in amazon? tomorrow I am goind to Panama, I can buy it for you... :twothumbs

Re: Red Mag Shorty P7 0.9v-4.2v Driver, Led Forward Clickie w/Led Glow, and Belt Clip

Changchung said:

I leave in Venezuela, but, for security reason you should shipp the flashlight to USA Florida, then their send it to me... Can you show me a link in amazon? tomorrow I am goind to Panama, I can buy it for you... :twothumbs

Click to expand...

The only place you would find that is in the UK area
Hmm.. I know! ill shoot you a PM..

Ok...