Angryfox        
Page 1 of 28 1234567811 ... LastLast
Results 1 to 30 of 814

Thread: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / NICHIA 92CRI (part 10)

  1. #1

    Default P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / NICHIA 92CRI (part 10)

    PART 9 !!! P60 Style Custom Drop - in modules for SF and other Products. (part 9 can be found here)

    Here I am offering P60 Style drop ins, they are available with Leds from the following manufacturers with some of the leds that will be offered are below.

    SSC Seoul - P7 , P4
    Cree -
    XML , XPG, XP-E, MC-E, XRE , UV, are here in warm , neutral or cool white
    Osram - Diamond Dragon , Golden Dragon Plus, Platinum Dragon IR/
    Luminus - SST -50, SST -90


    These modules will fit most flashlights that accepts a standard P60/D26 Style module.

    THESE DO NOT FIT OLD STYLE G2 HOSTS

    IF a GREAT host is needed here are some great hosts by Five Mega to look at (HERE)


    Here is one of the emitter in the base and converter board





    View of the module from the top and typical beam shot


    You can still see a bit of a doughnut hole in this picture but most of the time we can focus all or most of it out.

    This is a picture of the reflector made for the Cree XPE XPG This gives a very smooth and concentrated hotspot.


    New OPTICS Modules for XRE only



    All of the modules end up being as close to standard length as possible The large die leds are much thicker and there is a small possibility that there will be a crack at the head and body. I keep all as short as possible so if there is a crack there is probably nothing that can be done.

    All hosts are slightly different and one module may fit tight in a SF product and a bit loose in a FM Nite clone or an FM C but they will fit all. One may need to have the spring cut down to allow the head to close or a whole spring may be needed to keep the module from rattling. They also fit most Solarforce or any P60 style host


    Most LED's are carried in Cool White, Neutral White, or Warm white when possible. They will be listed if in stock if not listed probably not in stock.

    Battery configs listed are for any battery that falls into the range listed.

    Potting is the filling of electronics cavity with thermal epoxy for heat management and shock protection. Copper tape is included with potting and both are included at no charge unless specified by member.

    ALL MODULES ARE LEAD FREE, ALL SOLDER USED IS LEAD FREE


    EMITTERS CARRIED

    Seoul P7 $65 - 3.6v - 6volts ONLY /

    1- 3 or 4 levels regulated /Cool White

    __________________________________________________ _______________________

    CREE LEDS
    http://www.cree.com/products/xlamp.asp binning and tint informaiton (GREAT RESOURCE)

    Cree XM-L $40


    U2 flux bin 1A 6500k+ Cool White

    T60 flux bin 3C 5000k daylight white

    T50 flux Bin 4C 4300K neutral white

    T40 flux bin 5B3 4000k neutral white

    T40 flux bin 6A3 3500k Warm white

    T30 flux bin E7 3000K Warm White


    Direct drive
    1 Level only (potting and tape included this model only)
    works well in the 26650 Cooly's by Five Mega. Not made for continuous run.
    __________________________________________________ ______________________________________

    1 level 2.2 amps 3.6-16 volts best for use with Multiple cells.
    __________________________________________________ ______________________________________

    Available levels with memory (2.8-6 volts only) 3Amp stock
    1 level Regulated
    3 level Low / Med / High Regulated
    3 level Low / Hi / Strobe Regulated
    4 level Low low/ low / Med / High


    6 volt Drivers are 3 amps stock and can be pushed at and
    3.5 amps or even 4.2 amps but high should be used for shorter periods these do work well in the 26650 Cooly's by Five Mega.
    and in
    2P 18650 P60 M*g 1D by Fivemega There is no extra charge for these.

    If you want to use continuously on high in most hosts please use 3 amps for better heat control and you will also get much better runtime.

    Either Smooth OR Op reflectors available (extra reflectors not available at this time.)

    Potting with copper tape is now included
    __________________________________________________ ______________________

    XML TOWER MODULES $80 NEW!!!!

    T6 flux 1A tint *ONLY EMITTER AVAILABLE AT THIS TIME*

    Any of the above 6 volt max drivers listed under XML's plus ones listed below

    1 level 4-16 volt 2.2 amp driver

    Fits any of the surefire turbo heads such as KT1 / KT4 / KT5
    __________________________________________________ ______________________

    Cree XP-G -$35 *mixture of throw and flood*
    2.8-6 (levels are 100% / 40% / 5% )

    5 level low / med / high/ SOS / Strobe with memory / 1.4 amp / 1/7 amp
    5 level moonlight/ low low / low / med / high 1.5 amps
    3 level low / med / high 2.8-6 volts with memory / 1.4 amp / 1.7 amp
    1 level 2.8-6 volts

    1 Level 4-14 volts / 1.5 amp
    3 levels high / med/ low / 3.6-9 volts no memory / 1.4 amp
    3 level 1v-4.2 volts for low voltage for A / AA lights
    Flux Bins and tints that are available for XPG


    Q23000K 7A3 (90 minimum CRI) NEW
    Q4 2900k 8A4 tint
    R4 4000k 5B3 tint /5B2
    R4 5000k 3C tint
    R5 5500k
    - 2T tints (Cool White comparable to WH tint)
    S2 6300k - 1T tints (coolwhite comparable to WF tint)


    DUAL XPG (Linger Special)$45 Any of the above bins are possible / 3 level 2.8 amp 3.6-6 volts max *Floody* (levels available are same as XML)

    DBS MODULES AVAILABLE ON REQUEST for most emitters / brass pill only no reflector/ same price as regular modules, potting is available on these also.
    __________________________________________________ ______________________
    NICHIA

    4500k 92CRI neutral ($35)

    Driver Levels the same as the XPG's above


    __________________________________________________ ________________________

    CREE XPC $30 (new)

    Q5 WC tint available in 1 / 3 levels with memory in 1.4 or 1.7 amp
    __________________________________________________ ______________________

    Cree XRE - XPE -$30 -
    1.4 or 1.7 amp with memory
    2.8 - 6 volts 3 level regulated high / med / low
    2.8-6 volts 5 levels regulated - high / med / low / SOS/ strobe

    3.6 -8.4V regulated @ 1.4 amps - 3 levels high / med/ low

    XPE Good Throw
    R2 or R3
    available coolwhite / (Q3 5B)
    neutral /warm tints
    XPE Green , Red, Amber /Blue

    XRE (Good Throw )
    R2 flux WF tint
    Q45B neutral
    8E7 warm white
    Green and Blue colors

    Smooth OR OP reflectors are available

    Optics are for XRE emitters only
    / Cool white , neutral white and warm whites.

    8degree/ 60 degree.

    $37 for module and 1 optic $40 with 2 optics
    __________________________________________________ _________________________

    Cree MCE $ 55 - GOOD FLOOD

    1 - 3 or 5 level regulated
    3.6 - 6 volts

    Cool - M bin WD, WG
    Cool - Nbin no tint supplied but pure white
    Neutral - Kbin 5B tint
    Warm bins JE5, JE6, KA3
    __________________________________________________

    OSRAM LEDS


    Osram Diamond Dragon $40 - 3.6 -6 volts / 1/ 3/5 level
    Ultra White /WARM WHITE/True Green / Red

    Platinum Dragon - $40 Hyper-Red this is a true red no orange red. __________________________________________________ ___________________________

    LUMINUS SST SERIES LEDS

    Luminus SST-50 - $55 -

    2.8 -6volts only *good throw with adequate spill*

    direct drive
    1 Level direct drive

    Regulated with memory offered with same amperages as XML's listed above
    1 level
    3 level -- Low - Med - high
    3 level -- low- high- strobe
    4 level -- Low Low- low - med - high

    Flux Bins are

    6500K Cool White
    (W65S-GJ102-WJ-G4 )
    5700k (w57S-GJ201-WJ-H4 )
    4500k (w45S-GJ400-WJ-P3 )

    DBS MODULES AVAILABLE ON REQUEST *pill only*


    Luminus SST -90 -$70 -

    2.8 -6 volts only *Floody*

    1 Levels direct drive
    Also available in regulated drivers with memory of the same amperage drivers used with XML's above
    6500 (W65S-WN-G3 )
    5700k (W57S-WN-H4)
    3000k warm 83CRI ( W30M-GK700-WK-U3 )

    Green - Red
    - Blue Colered SST90's also available
    __________________________________________________ _________________________

    UV LEDS

    Cree UV XL 7090 $45 (395nm)3.6 v-6volts /1 level
    __________________________________________________ _________________________


    OSRAM IR LEDS

    Osram Platinum Dragon IR $45 (850 940nm)-3.6v- 6 volts /1 level 2.8-6 volts

    Quad Die 10watt IR great for night pictures

    __________________________________________________ _________________________

    I also have

    Seoul P4 - CW / Neut / warm 90 CRI


    please PM for info on these
    modules
    __________________________________________________ _________________________


    I try to keep the above listed led's in stock, I also try to keep the newest and most popular bins and color temps from cool whites / neutrals / and warm white high CRI models.

    Now as to levels in drivers , most of the time the levels are fixed and can't be changed. As new drivers become available the offerings will change on this page so please check it first. I often will have to change depending on what drivers I have available to me at the time so please check this page and I will update as needed.

    Please specify what host and batts you are using when inquiring about a module or led. Just remember if you don't see it or don't understand something just write as I don't mind helping but check this page first. These are not try and buy!

    Now that said the search button for the forum has a wealth of knowledge, much more than I can ever remember and usually with in days of a new led release runtimes and lumens are often posted please check the forum's search box as it is invaluable.


    When ordering please post your order in this thread plus put details in Paypal notes of what emitter and tint ordered/ include choice of reflector / # of levels / check to see if shipping address is visible . Also please list CPF Nickname in paypal notes.

    Shipping is 3 working days Although next day is not unusual Shipping confirmations are sent when mailed


    Make sure your address in paypal is correct becuase that IS WHERE IT WILL BE SENT.

    If you want it mailed to an alternate address
    from the paypal address please state I want my parcel sent to an alternate address if this is not done I will think it is a duplicate address and will send to what is listed on PP.


    MY Paypal info in biography or PM for it / I do not send confirmations that I received your paypal if properly addressed then I WILL receive it, you should be receiving a receipt from paypal when sent.


    Shipping Conus is included 1st class,
    Domestic Priority is $5 for up to 3 modules

    International shipping is $5 for 1st class Int up to two modules , Priority Mail Int. is $15 up to 3 modules , express mail and more than 3 modules quoted.


    Beam shots are posted below and new products will be posted below. Please send your beam shots and I will try to list when possible or create a link to them.

    New offerings will be listed below as they become available.


    D36 for M STYLE and M to C lights are (HERE)

    IN NEED OF A HOST THEN HERE ARE SOME GREAT FORUM MEMBERS THAT CAN HELP

    Here on BST get Five Mega hosts (Here) These are some of my favorites and the new coolys

    On marketplace get Fivemega 18mm Bodies in 5 Sizes Here
    Jason will take care of you.

    For milling of maglites and general millwork Will Quiles is the master and can be found (HERE)

  2. #2

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Reserved

  3. #3

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hi All this will be a NEWS SECTION where I will post NEW items and such.

    I have started another section so there is not so much information a person has to parse. Most of the offereing are the same and of course the QUALITY will always be there.

    I have a couple of new emitters I am working with and will post once I feel comfortable they will work as they should.

    3/20/2012 - ?
    I will be closed for the next few days as I have some minor surgery scheduled, hopefully I will be back online by the end of the week. All orders have been processed.

    If one wants to order that is not a problem but shipping may be a day or two more than my usual 1-3 days. I have made up alot of the more common tints ( U2 / 3C / 4C ) and should ship close to ontime. Questions may take a day or two to answer until I become more mobile.

    Thanks

    Dave


    4/7/2012 LOW POWER VAMPIRE DRIVERS

    HI

    OK Will Quiles has made some Very Low Voltage Drivers, these are for draining every last drop of voltage from old alkaline or NIMH batts. They will work up to 3 volts so you can use a 1XCR123 primary. You can read about it in his thread HERE at Will's Joule Thief thread , I have had many requests for so called vampire modules that would do just this run for long periods of time and drain every drop of juice left in the batts. Now these are not super duper bright lights but are certainly bright enough to walk around with and use in many other tasks. They make good emergency lights and everyone has old remote batts and toy batts.

    I have tested these with a 3C daylight white XPG and a 3C XML and what I have found is that the XPG and XML are about the same brightness when running with a new 1XCR123 primary, the XPG will have a slightly better hotspot and the XML slightly more floody but basically the same brightness. I would say at 3 volts the brightness is slightly brighter than the LOW level on one of my stock XPG modules.

    I also tested at 1.5 volts and the XPG was brighter than the XML but both could be used in a emergency lighting situation. I believe the reason the XPG is brighter is that the VF of the XPG is lower.

    The way Will and I are working this at this time is if you want me to build your module go to his thread and buy the driver from him and have him send the drivers to me. The cost for me to build is the posted price on this thread for the emitter you want. If you choose a XPG then it will be $35 as posted, I am including potting for no upcharge on these modules. If you choose a XMl then it will be the standard $40. Shipping is included in the US as always.

    As for emitters about any of the Cree emitters will work but if you looking for long lasting I think you will find that the lower VF emitters such as XPG or XPE will be brighter longer. This can be any of the tints that I stock and you can also use colors such as red

    Pictures of the driver and module can be seen on post #41 of this thread

    Thanks

    Dave


    4/16/2012

    Hi all

    A few of you have asked for the Nichia neutral 92CRI so I have ordered a few of the emitters. They are on backorder but there is no need to pre order as I am sure there will be enough. Once I get them I will post in the thread as I see no need to clutter the forum with a separate thread. They should price the same as a XPG module.
    As always I am trying to keep what you all are looking for.

    Thanks

    Dave

    4/21/2012

    Nichia 4500k 92CRI emitters are now in stock and are priced the same as the XPG's

    Thanks




  4. #4
    Flashaholic write2dgray's Avatar
    Join Date
    Mar 2009
    Location
    Princeton, NJ
    Posts
    303

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Nice work Dave, your selection has expanded nicely and I'm really enjoying the last 3-mode potted XM-L T5 flux 4C tint driven at 3A. Top quality - you're an asset to CPF and we wish you a painless/speedy recovery .

  5. #5

    Default

    I'll take:

    XML U2 6400K tint
    3A 1-mode regulated 2.8-6v
    OP reflector
    Potted w/ copper tape

    $45

  6. #6

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    I'll take a single mode (super duper bright) XML U2 1C Direct Drive 4.2 amps. SMO Reflector. No rush on the delivery and my prayers to a speedy recovery to one of CPFs Greats. Thanks Mr. Lemert!

    PP $40 Payment Sent (Unique Transaction ID # 6R18444861059544L) for my 12th NB XML drop-in.
    Last edited by BIGLOU; 03-22-2012 at 05:34 PM.

  7. #7
    Flashaholic
    Join Date
    Nov 2011
    Location
    PATRIOT NATION
    Posts
    308

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hope your recovering VERY quickly Dave! Thank you for the service youve offered to all of us serviceman and CPFer's=) Blessings be upon you

  8. #8
    Flashaholic
    Join Date
    Sep 2011
    Location
    Indonesia
    Posts
    116

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    hi, do you have a single mode for the XRE? does optic means a lens? will it fit a surefire 6p or solarforce body? thanks.

  9. #9

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Nailbender - Cree xpe-r3 3.6 -8.4V regulated 3 levels high / med/ low ( yes - memory) cool white pill for my DBE. please.

    paypal sent
    Last edited by oal; 03-24-2012 at 05:30 PM.

  10. #10

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part



    XM-L T30 flux bin E7 3000K Warm White. Single level regulated, 2.8-6 volts, 2.8amps, orange peel reflector and with thermal potting and copper tape. International shipping required.

  11. #11
    Tana's Avatar
    Join Date
    Mar 2011
    Location
    Bosnia & Herzegovina
    Posts
    1,786

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Good luck with the surgery and fingers crossed for fast recovery...

  12. #12
    Flashaholic* yifu's Avatar
    Join Date
    Oct 2011
    Location
    Australia
    Posts
    713

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Wish you a speedy recovery!

  13. #13

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Quote Originally Posted by rewdee View Post
    hi, do you have a single mode for the XRE? does optic means a lens? will it fit a surefire 6p or solarforce body? thanks.
    I'm not Nailbender but yes, he does and yes, it does fit. These are great modules. An optic is sort of like a lens. It's more like a beam shaper. It takes the place of the reflector and causes the light to be thrown in a reasonably tight beam. I've been meaning to do comparative beamshots for ages. Maybe I'll have time this week...

    Good luck with the surgery and get better soon!

  14. #14

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hi All

    Thanks for all the good wishes, it has taken me about twice as long for recovery as I was originally told but maybe that is because I have more than twice as many holes in me as I was told I would have Anyway I am back up sitting for longer periods and hope to get all the PM and posts answered by end of tomorrow.

    I also hope to be back in the shop Tuesday, I am sure I will be a bit slower but it won't take long to catch up! I should be able to answer PM's and posts daily after today.

    Sorry for any delays

    Dave

    Thanks to RCantor for answering the one post, as he said if you like the look of a surefire with a lens then you will like this but if you are looking at the lens to increase throw over a smooth reflector then you may be dissappointed. As he said it will smooth out some of the rings that are visible when wall hunting with a XRE in a smooth reflector and will keep the beam tight but it will not give better throw than a reflector will.

  15. #15
    Flashaholic dandruff's Avatar
    Join Date
    Feb 2004
    Location
    singapore
    Posts
    244

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Cree XML T60 3C, 2.8-6 volts, 3 level Low / Med / High Regulated, 2.8amps, OP Reflector, Potting with copper tape.

    to fit Surefire 6PD with 2x CR123 primaries, and maybe a 18650 at some point in the near future.

    Module + Potting + 1st Class international shipping = 45 + 5 + 5 = $55. Paypal sent!

    I have also PM'ed you.

    Thanks and speedy recovery!

  16. #16
    Flashaholic
    Join Date
    Sep 2011
    Location
    Indonesia
    Posts
    116

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Quote Originally Posted by nailbender View Post
    Thanks to RCantor for answering the one post, as he said if you like the look of a surefire with a lens then you will like this but if you are looking at the lens to increase throw over a smooth reflector then you may be dissappointed. As he said it will smooth out some of the rings that are visible when wall hunting with a XRE in a smooth reflector and will keep the beam tight but it will not give better throw than a reflector will.
    Hi, thanks for the prompt response. Hope you get well soon.

    I was thinking about throw, but a nice tight beam is very tempting. Will give it a thought. thanks.

  17. #17
    Flashaholic* yifu's Avatar
    Join Date
    Oct 2011
    Location
    Australia
    Posts
    713

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Quote Originally Posted by rewdee View Post
    Hi, thanks for the prompt response. Hope you get well soon.

    I was thinking about throw, but a nice tight beam is very tempting. Will give it a thought. thanks.
    If you want throw, just ask Dave (Nailbender) to take off the reflector and just ship the 1.4A XR-E pill. Then screw it onto an Ahorton Aspheric P60 spacer kit available here
    http://www.candlepowerforums.com/vb/...ses-headlamps-...)
    This would get you about 5 times the throw of the TIR optic.

  18. #18
    Enlightened
    Join Date
    Apr 2011
    Location
    Montréal
    Posts
    91

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hi Dave, hope you're feeling better, I'd like one of these:

    XM-L $40
    T50 flux Bin 4C 4300K neutral white
    2.8-6 volts
    3-mode L/M/H Regulated (3.5a on high)
    Smooth reflector (unglued please)
    Potted with tape $5
    International Shipping $5

    Total: $50


  19. #19
    Flashaholic* yifu's Avatar
    Join Date
    Oct 2011
    Location
    Australia
    Posts
    713

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Got my 90 minimum CRI drop in! Nice tinit!

  20. #20

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Quote Originally Posted by yifu View Post
    If you want throw, just ask Dave (Nailbender) to take off the reflector and just ship the 1.4A XR-E pill. Then screw it onto an Ahorton Aspheric P60 spacer kit available here
    http://www.candlepowerforums.com/vb/showthread.php?308032-Ahorton-s-sales-(Lenses-headlamps-...)
    This would get you about 5 times the throw of the TIR optic.
    Before few days I made ​​such a combination and must say that i am very satisfied. Using in L2P solarforce, the light have a nice bright beam and the spot has very nice projection and size of the led. Excellent thrower for my needs.

  21. #21

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hi All

    I am now caught back up and all orders have now shipped, sorry for any delays.

    All orders should now ship with in 3 working days or less as usual.

    Dave

  22. #22

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    PP Sent for:

    XRE Drop In ($30)
    1.7A 2.8-6v 3 mode, HML (w/ memory if possible... w/o memory is fine also)
    Q45B Tint (neutral)
    Potted ($5)
    Smooth Reflector, but not glued to pill

  23. #23

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Paypal sent for:

    Cree XM-L
    T60 flux bin 3C 5000k daylight white
    1 level Regulated
    Orange peel reflector
    Potted
    for 2x123A primaries

    $45+5 potting=$50
    (Unique Transaction ID # 4W380522TD657913V)

  24. #24

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    I'm back, lol.

    I need a TIGHT beam, able to be run by one primary or rcr, with around 200-250 lumens, one mode. Potted, able to withstand recoil of a 12 ga. Prefer a more neutral tint, but as long as it's not blue, i'm happy.

    You got anything for me?
    Let there be light!

  25. #25

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Quote Originally Posted by AMkrew View Post
    I'm back, lol.

    I need a TIGHT beam, able to be run by one primary or rcr, with around 200-250 lumens, one mode. Potted, able to withstand recoil of a 12 ga. Prefer a more neutral tint, but as long as it's not blue, i'm happy.

    You got anything for me?
    HI

    If you truly want a tight tunnel like beam then the XRE is it, if you want a bit more spill then choose XPG. The XRE will be about 280-290 lumens which should fit well.

    As for working with a 12ga that will not be a problem.

    Dave

  26. #26

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Quote Originally Posted by hotlight View Post
    PP Sent for:

    XRE Drop In ($30)
    1.7A 2.8-6v 3 mode, HML (w/ memory if possible... w/o memory is fine also)
    Q45B Tint (neutral)
    Potted ($5)
    Smooth Reflector, but not glued to pill
    Quote Originally Posted by diverge View Post
    Paypal sent for:

    Cree XM-L
    T60 flux bin 3C 5000k daylight white
    1 level Regulated
    Orange peel reflector
    Potted
    for 2x123A primaries

    $45+5 potting=$50
    (Unique Transaction ID # 4W380522TD657913V)
    Hi

    Yours have shipped check your email for notices.

    Dave

  27. #27
    Unenlightened
    Join Date
    Mar 2012
    Posts
    1

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    KILLER_K contacted you for me about the G2 I have and want a custom module such as you made for him. Do you have an email address I can contact you at for further discussion?

  28. #28

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    PayPal sent for:

    XML U2
    2.8-6 volt regulated; 3 mode (High, Med, Low) with memory
    reflector Smooth
    $5 for potting and tape
    Total $40 + $5 = $45

  29. #29

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hi Dave,

    I was intersted in getting the XP-G S2 6300k -- 5 level 1v-4.2 drop-in, but I noticed your note saying that this doesn't work for L2R hosts. I was planning to run this with 3xNiMH aa cells in a FM 3AA host. Would that match up well with this module? Also, can this module be had in anything but 5 modes (1 mode or 3 mode hopefully)? Lastly, on 3xNiMH aa cells, what would be the expected OTF lumen output?

    Much thanks!

  30. #30
    Flashaholic
    Join Date
    Sep 2011
    Location
    Indonesia
    Posts
    116

    Default Re: P60 modules -warm, neutral, cool white/XRE-XPE-XPG-S2-XML-U2 / P60 modules (part

    Hi Dave,

    Paypal sent for:
    1x XP-G (90 CRI) 1 level regulated 2.8-6 volts/1.4 amps.
    1x intl shipping

    Total USD 40. (Unique Transaction ID # 6DV38887HN2780944)

    Thanks.

Page 1 of 28 1234567811 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •