yaesumofo
Flashlight Enthusiast
FS: \"C\" cell O-Sink. 2 . UPDATE at end of thread
Yes, I am very happy to announce that our friends at Flashlightlens will be handling all O-Sink order fulfillment from now on. Flashlightlens
I am sure you will be happy with his great service!!
I am still the person making and doing design tweaks so feel free to post as always right here with any questions or concerns!
Yaesumofo
PS please be patient. "C" cell units are in production!! We will have them very soon.
Thanks
Hi Guys. Some time ago I needed some hotlips. There were NONE to be had. One thing led to another and I decided to have a few "D" cell O-Sinks made. I did have a problem with Hotlips. I was bad at centering the emitter. I am Just bad at at.
I had a 10% failure rate. I found it frustrating and expensive. This required a redesign of the pedestal. So that is what I did. You see the result here in a "C" version:
Guess what!! It works perfectly!!
Based on the sucess of the "D" cell version I did a run of "C" cell O-Sinks.
The "C" cell O-Sink is beefier. Thicker where it counts = more surface area to transfer heat.
The pedestal is taller.
The emitter leads are offset to the holes by 20 degrees.
The counter bore accommodate an e-CAN (as requested by a few people).
Not to mention the emitter self centering.
All in all Very Much improved.
There are 2 sizes. OLD MAG (ONLY A FEW UNITS left) and NEW MAG.
Please make sure of the size you need. It is a lot of extra work to fix if the wrong O-Sink is orderd.
$10.50 shipped via USPS to your door In The USA. For Worldwide international shipping except Canada. Please add $4.00 for the first O-Sink and $1.00 for each additional O-Sink.
For international shipping to Canada. Please add $1.00 for the first O-Sink and $.50 for each additional O-Sink.
PayPal to:
[email protected]
Please indicate size: OLD or NEW
Please include your shipping address in the PayPal note/comments when paying. Also Please include your CPF Name.
Thank you.
Yaesumofo
More info and production photos:
C cell production
Yes, I am very happy to announce that our friends at Flashlightlens will be handling all O-Sink order fulfillment from now on. Flashlightlens
I am sure you will be happy with his great service!!
I am still the person making and doing design tweaks so feel free to post as always right here with any questions or concerns!
Yaesumofo
PS please be patient. "C" cell units are in production!! We will have them very soon.
Thanks
Hi Guys. Some time ago I needed some hotlips. There were NONE to be had. One thing led to another and I decided to have a few "D" cell O-Sinks made. I did have a problem with Hotlips. I was bad at centering the emitter. I am Just bad at at.
I had a 10% failure rate. I found it frustrating and expensive. This required a redesign of the pedestal. So that is what I did. You see the result here in a "C" version:
Guess what!! It works perfectly!!
Based on the sucess of the "D" cell version I did a run of "C" cell O-Sinks.
The "C" cell O-Sink is beefier. Thicker where it counts = more surface area to transfer heat.
The pedestal is taller.
The emitter leads are offset to the holes by 20 degrees.
The counter bore accommodate an e-CAN (as requested by a few people).
Not to mention the emitter self centering.
All in all Very Much improved.
There are 2 sizes. OLD MAG (ONLY A FEW UNITS left) and NEW MAG.
Please make sure of the size you need. It is a lot of extra work to fix if the wrong O-Sink is orderd.
$10.50 shipped via USPS to your door In The USA. For Worldwide international shipping except Canada. Please add $4.00 for the first O-Sink and $1.00 for each additional O-Sink.
For international shipping to Canada. Please add $1.00 for the first O-Sink and $.50 for each additional O-Sink.
PayPal to:
[email protected]
Please indicate size: OLD or NEW
Please include your shipping address in the PayPal note/comments when paying. Also Please include your CPF Name.
Thank you.
Yaesumofo
More info and production photos:
C cell production