Sold/Expired Sinner Customs - Tri-EDC's and more - this run CLOSED

[Tejasandre]

Re: Sinner Customs - Tri-EDC's and more.

Order placed.
Titanium 18350 Tri-EDC host
Nichia 219b Light Engine
FET driver
Titanium Pocket Clip
Sinners Crown (Crenelations)

... Now the waiting...

 

[aZhu]

Re: Sinner Customs - Tri-EDC's and more.

Order placed.
Titanium 18350 Tri-EDC host
Nichia 219b Light Engine
FET driver
Titanium Pocket Clip
Sinners Crown (Crenelations)

... Now the waiting...

I've been waiting for a little over a week now... it gets worse each day that goes on...

 

[Tejasandre]

Re: Sinner Customs - Tri-EDC's and more.

I've been waiting for a little over a week now... it gets worse each day that goes on...

Lol. That's what I was afraid of. My wait is projected @ 2-3 weeks.

 

[Reellegend01]

Re: Sinner Customs - Tri-EDC's and more.

He's pretty dead on two week wait wich is not bad for hand made art I think but yes iam excited too lol

 

[Tejasandre]

Re: Sinner Customs - Tri-EDC's and more.

He's pretty dead on two week wait wich is not bad for hand made art I think but yes iam excited too lol

Wasn't complaining. I meant I was afraid the wait gets worse by day.

The eta was informational.

 

[Croquette]

Re: Sinner Customs - Tri-EDC's and more.

Have ordered 10 days ago a 18650 ti with crenelation, trit slots, FET and xp-l...
The waiting time is 4 weeks and I found that to be pretty quick so.
Just to be patient.

 

[Gilgamesh]

Re: Sinner Customs - Tri-EDC's and more.

How's the clicky in it? Replaceable if it were to fail? Also what size boot does it take?

 

[gunga]

Re: Sinner Customs - Tri-EDC's and more.

I don't know about the newest line but the current lineup uses omten reverse clickies. I don't have the number handy but they are easy to find. You just have to resolder the switch of you change it. It's a 16mm boot.

 

[DellSuperman]

Re: Sinner Customs - Tri-EDC's and more.

The 3 host that i use don't require soldering during change. Just bending one of the edge upwards towards the button & the other downwards towards the base.
But u gotta be careful with bending them cause to many bends & they will snap.

 

[gunga]

Re: Sinner Customs - Tri-EDC's and more.

You are right. I stand corrected.

 

[Jtolly]

Re: Sinner Customs - Tri-EDC's and more.

Hey guys... Not new to CPF, but haven't posted much.

Just ordered 2 Sinner Customs about a week ago (Ti 18650 and Ti18350). The reason I'm posting is I would like to know the best batteries to use for performance and longevity in these lights. I already ordered some Efest Purple IMR 18650 2500mAh 35A 3.7v Flat Tops and per sinners recommendations 18650 3200mah max 10A INR18650 Battery MH1 LG Chem 3.6V flat tops for the 18650 light. I would like to know the best batteries for my 18350 and if the 18650 batteries I have are what I need. I also have a NITECORE i4 Intellicharge and Pila IBC Charger. Any thoughts on those would be appreciated, also.


Joey

 

[DellSuperman]

Re: Sinner Customs - Tri-EDC's and more.

Those batteries are what i have been using for some time now & they haven gave me any problems so far.
The chargers are good to go as well

 

[akhyar]

Re: Sinner Customs - Tri-EDC's and more.

My 18350 Ti Tri-EDC should be shipped within this next few days, as what was told by Sulman.
I've these 3 batteries on stanby already
The Keeppower is only rated up to 8A continuously while the AW can go upto 12A continuosuly, so the AW will be my main battery.

As for charger, I also have the Nitecore i4 charger, which is a solid charger but just to slow for me as I also have the Opus BT C3100 and Xtar VC4 chargers.
If you're OK with the slow charging speed of the i4, it should be good especially if you willing to charge 2 batteries the most at one time.

 

[Jtolly]

Re: Sinner Customs - Tri-EDC's and more.

So, Its ok to use button tops in the 18350 lights then? I thought you were only allowed to use flat tops? I know button top 18650s won't fit in the 18650 lights, but I wasn't sure on the 18350s.

 

[akhyar]

Re: Sinner Customs - Tri-EDC's and more.

Oh bummer! If the 18350 doesn't accept button-top, I'd have to use the Keeppower then

 

[mcbrat]

Re: Sinner Customs - Tri-EDC's and more.

I used IMR button tops in 18350

 

[akhyar]

Re: Sinner Customs - Tri-EDC's and more.

I used IMR button tops in 18350

Thanks!
Good to hear that

 

[Eric242]

Re: Sinner Customs - Tri-EDC's and more.

I received mine today, thank you Sulman :thumbsup:
I´ll post some pictures of the light (with crenelations and tritium slots) when I´m able to (lower back pain is killing me right now).

Eric

 

[Reellegend01]

Re: Sinner Customs - Tri-EDC's and more.

Awsome!!! Yes we need pics mine should be coming soon

 

[aZhu]

Re: Sinner Customs - Tri-EDC's and more.

I received mine today, thank you Sulman :thumbsup:
I´ll post some pictures of the light (with crenelations and tritium slots) when I´m able to (lower back pain is killing me right now).

Eric

Awesome! Can't wait to see it. When did you place your order and how long did shipping take?