Sold/Expired FS. Titanium Bezels for SF 6P,C2,G etc. Also JetBeam ProIII

[russtang]

I have 33 pieces of these Titanium 6al4v Bezels for the SF 6P, C2-3, G2 etc. I don't know if they will work with any of the SF "clones"

They will also fit the Jetbeam ProIII.

They are approx. .170 thick, not including the threads. Just the right size.

$25.50 each
*no extra fees

$3 shipping first class usa or international. should cover 4-5 pieces
Claim yours here in this thread please.

send pp to sales(at)uniquetitanium.com with a note what payment is for.

for MO, pm me for info.

 

[Armed_Forces]

...I already ordered the SS bezels from Mike and now you post this!



No removal tool??? ..those stock SF rings can make a preacher cuss!!

 

[Nitroz]

...I already ordered the SS bezels from Mike and now you post this!

+1 :hairpull:

 

[russtang]

...I already ordered the SS bezels from Mike and now you post this!



No removal tool??? ..those stock SF rings can make a preacher cuss!!

If you don't have a tool:
I just hold the head with some needle nose pliers in some almost boiling water for about a minute or two and then use some split-ring pliers to remove the stock bezel-holding the head with a pot-holder.

I've done that 2-3 times and it worked ok.

Its OK to have SS And Ti bezels. Just rotate them every few days like a watch band.

 

[Winx]

for one.

I have different bezel rings so maybe I need to rotate them all once in a week.

I wouldn't try to remove the ring without heat. All three I have opened had some kind of glue which softens when heated. Hair dryer was efficient in my case. Cheapest acrylic removal tool is sold by flashlightlens.com.

 

[NetKidz]

for one.

:thanks:

 

[russtang]

for one.

I have different bezel rings so maybe I need to rotate them all once in a week.

I wouldn't try to remove the ring without heat. All three I have opened had some kind of glue which softens when heated. Hair dryer was efficient in my case. Cheapest acrylic removal tool is sold by flashlightlens.com.

for one.

:thanks:

I will get these out tomorrow.(Wed) its late errr..early??

 

[russtang]

for one.

I have different bezel rings so maybe I need to rotate them all once in a week.

I wouldn't try to remove the ring without heat. All three I have opened had some kind of glue which softens when heated. Hair dryer was efficient in my case. Cheapest acrylic removal tool is sold by flashlightlens.com.

for one.

:thanks:

Shipped. Thanks

 

[sixshooter_45]

...I already ordered the SS bezels from Mike and now you post this!



No removal tool??? ..those stock SF rings can make a preacher cuss!!

I've used a gripping pad wrapped around a 1/2" dia. brass rod and laid it in between the lowest part of the crenelated bezel whilst gripping the head's hex's in my rubber padded vise. With a little downward pressure and a twist, pop, it comes right off!

 

[sixshooter_45]

I just ordered two ea.,

Payment Sent (Unique Transaction ID #89X067925Y2780502)
Sent to:
Email:
[email protected]

 

[russtang]

I just ordered two ea.,

Payment Sent (Unique Transaction ID #89X067925Y2780502)
Sent to:
Email:
[email protected]

Shipped. Thanks

 

[sixshooter_45]

Shipped. Thanks

Thank you! Can't wait! lovecpf :twothumbs

 

[Barbarian]

for one bezel


Thanks,
Tim

 

[donn_]

I'll take 2, please.



:thanks:

 

[NewtonGT]

for two bezels.

Thanks!

 

[sixshooter_45]

Thanks for the fast shipment and for very well made great looking strike bezel, I just ordered four new UCL optical lenses for my SF Z2 flashlights.

The threads were a little longer to the shoulder than my stock ones, which caused my lenses to crack.

The lenses I ordered are almost exactly the same amount less in thickness than the extra length of the these vs. mine.

A little rubbbing with some fine emory cloth on the threads on a flat surface would work if one wishes to keep the stock lens. A digital caliper would help with the measurement required as I'm sure they are differences from one to the next.

I'm not complaing as I was going to replace the Pyrex lenses anyway. Just a heads up for others.

An excellent product, thanks again!

 

[russtang]

for two bezels.

Thanks!

I'll take 2, please.



:thanks:

for one bezel


Thanks,
Tim

I'll get these out Mon. Thanks

 

[russtang]

for one bezel


Thanks,
Tim

I'll take 2, please.



:thanks:

for two bezels.

Thanks!

Shipped. Thanks

 

[NewtonGT]

Thanks Russ!!!

:thumbsup:

 

[Winx]

I got mine. Very, very nicely machined. Thanks!