LD10 head won't fit LD20 tube?
- Thread starter aau007
- Start date
Help Support Candle Power Flashlight Forum
tandem
Enlightened
If your LD10 head is newer (i.e. an R4) than your LD20 tube (which may be an earlier than R4 vintage), then yes, it is true - the threads in both the head and tail are square cut in the newer versions (better) and are now not backward compatible with prior generations of the LD10/20 lights.
(Noted in this review)
(Noted in this review)
batmanacw
Enlightened
I was told that the LD10 cannot handle lithium ion batteries that run 3.7v. It looses its low mode on slightly over 1.5v. How well is the LD10 head going to run off 3v?
I am guessing that the threads don't match so people will not lego them and blow the circuit.
I am guessing that the threads don't match so people will not lego them and blow the circuit.
Correct me if I am wrong. I thought the LD20 r4 and LD10 r4 uses the same head and tail, just a longer body for the LD20. No?
batmanacw
Enlightened
I think you better confirm that by checking with Fenix before you try it. If 1.7v is too much for low modes on the LD10, then how is 3v not too high?
I did not confirm with Fenix but instead, based it on the review here:
http://www.candlepowerforums.com/vb/showthread.php?t=277658
If selfbuilt did not blow up the light by using a 3.7V 14500 in the LD10 r4, I don't think 3V would kill it either.
batmanacw
Enlightened
Good luck. I would leave the lego work to Quark.
shark_za
Enlightened
Easy now boys and girls.
A lot of "I think so" here
The driver on the LD10/20 (yes same head) goes into direct drive somewhere around 3.2v.
You can run 1x Lithium 1.7v in the LD10 with absolutely no loss of modes.
You can run 2x Alkaline or 2x NiMh in the LD20 with no side effects, only when you run 2x 1.7v Lithiums do you run into issues. (3.4v)
Same with 1x 14500 Li-Ion 3.7v in the LD10.
Thread issues are as mentioned above.
I have not seen a LD20 tube for sale with the new thread pattern, my own LD10/20 was made from an older LD10 Q5 and L2D body.
A lot of "I think so" here
The driver on the LD10/20 (yes same head) goes into direct drive somewhere around 3.2v.
You can run 1x Lithium 1.7v in the LD10 with absolutely no loss of modes.
You can run 2x Alkaline or 2x NiMh in the LD20 with no side effects, only when you run 2x 1.7v Lithiums do you run into issues. (3.4v)
Same with 1x 14500 Li-Ion 3.7v in the LD10.
Thread issues are as mentioned above.
I have not seen a LD20 tube for sale with the new thread pattern, my own LD10/20 was made from an older LD10 Q5 and L2D body.
If I remember correctly the clip versions of LD20 and LD10 were the first to have square threads and broke the compatibility.
I've been using my LD10 Q5 head on LD20 body with no ill effects, and the output seems to be the same as the LD20 head on the same body.
I've been using my LD10 Q5 head on LD20 body with no ill effects, and the output seems to be the same as the LD20 head on the same body.
batmanacw
Enlightened
My LD10 looses low mode with lithium primaries. Its fine with alkaline or eneloops.
Is there more versions on the LD20? There is the Q5, R4 and now the "Clip" version?
shark_za
Enlightened
I would say your LD10 is pretty unique and probably broken then.
Normal LD10 heads can run with 2x1.5v=3v and maintain all modes.
batmanacw
Enlightened
Not even close to broken. Do a search on my name and a thread about it will come up. Mine is not even close to being rare. I even contacted 4sevens and they said it was perfectly normal. There was a thread about this less than a week ago.
shark_za
Enlightened
Could you point me to the thread please?
You have just confused the hell out of me, reading all your posts about the LD20 when we are talking about the LD10.
(LD20) 2x1.7v = 3.4v = problem
(LD10) 1x1.7v = 1.7v = works fine
You have just confused the hell out of me, reading all your posts about the LD20 when we are talking about the LD10.
Incorrect. The LD20 is a 2xAA light, the LD10 is a 1xAA light.
Only when you turn it into a LD20.
(LD20) 2x1.7v = 3.4v = problem
(LD10) 1x1.7v = 1.7v = works fine
batmanacw
Enlightened
I have had problems with my LD10 and LD20 with lithium primaries. Maybe I am remembering wrong, but that is one reason I dropped it from my get home bag. The second reason was the lack of a moon light mode.
The quote about the LD10 being a two cell light is either not mine, or a typo. I have both.
batmanacw
Enlightened
I was incorrect about the LD10. It can handle 3 v. My memory must be going. Apologies.
