P60 sized led drop-ins (part 2)

Status
Not open for further replies.

Fizz753

Newly Enlightened
Joined
Oct 23, 2006
Messages
138
Location
South West Michigan
While reading the thread titled "Dealextreme drop in for G2, 6P, etc???" I started making a list of the drop-in's I saw. It got a little out of hand. :sssh:
I thought I would put the list out here instead of buried 10 pages in to the above thread (no offense to the guys and gals in said thread :wave:)

If someone wants to shamelessly steal the list and add to / keep it updated feel free. :) Since I unfortunately wont have much time to do so.

** Don't forget to check out the P60 Flashlight List {host} post as well. (and add to it if you can :) ) **

** Lumens Factory **
http://www.lumensfactory.com/cart.php?cat_id=2&sub_cat_id=0

D26-LED High Output Single Mode LED Reflector Module (3.6V-13V)
$24.00 - 3.6V to 13V Regulated Input for Maximum Flexibility - High Output Cree XR-E, R2 LED
Maximum Current Output at 1000mA - High Colour Temperature (Cool White, 5000K-10000K according to Cree)
High Temperature Resistant Orange Peel Coating - Every Reflector Module is Pre-Focused for the Ultimate Spot

D26-LED Selected Warmer Tint Version (Limited Quantity) (3.6V-13V)
$28.00 - 3.6V-13V Regulated Input - Maximum Current Output at 1000mA - High Output Cree XR-E, R2 LED
Selected using Integrated Photometric Sphere to have Warmer Colour Temperature (5000K-5500K)
High Temperature Resistant Orange Peel Coating - Every Reflector Module is Pre-Focused for the Ultimate Spot


** Dealextreme **

Ultrafire Cree, Regulator, Reflector 1x18650 2xCR123A Lamp Assembly
http://www.dealextreme.com/details.dx/sku.1343
$10.92 accepted voltage: 3.6V ~ 9.0V 900mAh regulator board Orange-peel aluminum reflector

3W Cree, Regulator, Reflector 1x18650 2xCR123A Module Set
http://www.dealextreme.com/details.dx/sku.1447
$12.80 accepted voltage: 3.6V ~ 9.0V 900mAh regulator board Orange-peel aluminum reflector

DX 3W Cree Module CM1
http://www.dealextreme.com/details.dx/sku.3214
$10.82 3.2V~9.0V Input
Beamshots + review at: http://www.light-reviews.com/cm1/

SSC 42180-T 3W Emitter Reflector Driver Module
http://www.dealextreme.com/details.dx/sku.4068
$13.79 Input voltage: 3.7V ~ 8.0V Current: 900mA

3W Cree Drop-in Module (supports Surefire 6P)
http://www.dealextreme.com/details.dx/sku.6090
$10.14 3V~18V

Cree 5-Mode Emitter Reflector and Driver Module
http://www.dealextreme.com/details.dx/sku.4296
$14.80 Typical driving voltage: 3.7V (maximum voltage: 4.2V. Do not exceed.)

Cree Drop-in Module for Surefire 6P
http://www.dealextreme.com/details.dx/sku.6076
$10.00 Voltage Range: 2.9V ~ 9V

Cree Drop-in Module
http://www.dealextreme.com/details.dx/sku.7162 -
$12.48 Ultrafire 4-Mode 3.7V~6V

KLC8 LED Emitter with Driver and Reflector Module Set
http://www.dealextreme.com/details.dx/sku.8835
$9.90 (3.7V~6.5V Input)

Q5-WC 3-Mode 0~100% LED Drop-In Module
http://www.dealextreme.com/details.dx/sku.11074
$16.90 3-Mode: 0~100% (adjustable) > Strobe > SOS 3.7V
Review: http://www.light-reviews.com/dx_sku_11074/

Cree Q5 LED Drop-in Module
http://www.dealextreme.com/details.dx/sku.11621
$12.42 Input Voltage Range: 3.7V~18V Maximum Output: 200 Lumens

Cree Q5 LED 5-Mode Drop-in Module
http://www.dealextreme.com/details.dx/sku.11622
$13.55 3.6V~7.2V Input, Current and lumens are rated by the manufacturer
1. Low 25mA, 80LM
2. Mid 550mA, 120LM
3. High 950mA, 200LM
4. Strobe 800mA, 250LM
5. SOS 800mA, 200LM

Cree R2 Drop-In 1-Mode LED Module
http://www.dealextreme.com/details.dx/sku.11836
$12.40, Input: 3.7V~18V, Output: 117~225 Lumens (manufacturer rated)

Cree P4 1-Mode LED Drop-In Module
http://www.dealextreme.com/details.dx/sku.11810
$9.59 Input: 3V~12V

Cree Q2 LED Drop-In Module for WF-502B and Similar Flashlights
http://www.dealextreme.com/details.dx/sku.12501
$12.73, 3.6V~12V Input, Single mode regulated circuitry

Cree XR-E R2-WC 5-Mode 250-Lumen LED Drop-in
http://www.dealextreme.com/details.dx/sku.13658
$13.68 Input: 3.6V - 8.4V, Reflector: Textured, Memory: Unknown
Modes: High (250 lumens) > Mid (150 lumens) > low (80~100 lumens) > Strobe > SOS

Cree XR-E Q5 1-Mode Drop-in LED
http://www.dealextreme.com/details.dx/sku.13802
$11.80 Input: 3.7V - 12V, Textured aluminum reflector

Cree R2-WC 250-Lumen 5-Mode Memory Drop-in LED
http://www.dealextreme.com/details.dx/sku.14442
$12.90 - Input voltage range: 3.0V~8.4V - - Maximum brightness: 250 lumens (manufacturer rated)
5-Mode driver circuitry with mode memory: Hi > Mid > Lo > Strobe > SOS - Alumium textured/OP reflector

Cree R2-WC 3-Mode + 0~100% LED Drop-in
http://www.dealextreme.com/details.dx/sku.17593
$11.39, Input: 3.6V~8.4V, Cree XR-E R2-WC LED,
200 lumens (manufacturer rated), Aluminum textured reflector

__

** BugOutGearUSA **
http://www.bugoutgearusa.com/

*Premium* Cree Drop-In Module
$34.95 , 150 Lum, 4+ hours run time, 4.5V to 9V
http://www.bugoutgearusa.com/prcrdrmo.html

'Premium Plus' Cree drop-in
$39.95 , 170 Lum, 3+ hours run time, 4.5V to 9V
http://www.bugoutgearusa.com/cosoplcrmo.html

"Super Premium" Cree Q5 Drop-in
$49.95 230 Lum, 3+ hours run time, 4.5V to 9V
http://www.bugoutgearusa.com/crq5drmo.html

__

** Kaidomain **

Cree Q5 Drop-In 1-Mode LED Module
http://www.kaidomain.com/ProductDetails.aspx?ProductId=1775
$11.53 Voltage Range: 3V~18V

Cree R2 Drop-In 1-Mode LED Module
http://www.kaidomain.com/ProductDetails.aspx?ProductId=1769
$11.77 Voltage Range: 3.7V~18V, Output: 117~225 Lumens (manufacturer rated)

CREE XR-E P4, 6P Drop-in Module
http://www.kaidomain.com/ProductDetails.aspx?ProductId=1634
$8.94 Voltage Range: 2.7V - 6V
Runtime:
About 1.7 hours on two 3.0V CR123A cells
About 2.5 hours on 17670 Li-ion cell
About 3.5 hours on 18650 Li-ion cell

K2 LED Drop-in (26mm)
http://www.kaidomain.com/ProductDetails.aspx?ProductId=4880
$6.90

--

** Malkoff Devices - http://www.malkoffdevices.com/shop2/ **

M60 Mod to fit Surefire
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=7
$55.00 - Input voltage 3.8V - 9V, Current Draw 750ma at 6 volts, Led is a Cree XRE 7090
Runtime is 1 1/2+ hours on 2 CR123 primary batteries, solid brass heatsink construction
Utilizes a Cree 8 degree optic.

M60F 20 Degree Flood
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=22
$55.00 - Input voltage 3.8V - 9V, Current Draw 750ma at 6 volts, Led is a Cree XRE 7090
Runtime is 1 1/2+ hours on 2 CR123 primary batteries, solid brass heatsink construction
output is 220+ lumens, The optic produces an outstanding room lighting beam.
Throw is typically limited to approximately 120+/- feet. Utilizes a Cree 20 degree optic

M60L (Low Output)
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=8
$55.00 - Input voltage 3.8V - 9V, Current Draw 350ma at 6 volts, Led is a Cree XRE 7090
Runtime is 4 1/2+ hours on 2 CR123 primary batteries, solid brass heatsink construction
output is 140+/- lumens, Utilizes a Cree 8 degree optic

M60LF (Low output - Flood)
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=23
$55.00 - Input voltage 3.8V - 9V, Current Draw 350ma at 6 volts, Led is a Cree XRE 7090 Q5 WG tint
Runtime is 4 1/2+ hours on 2 CR123 primary batteries, solid brass heatsink construction
output is 140+/- lumens, The optic produces an outstanding room lighting beam.
Throw is typically limited to approximately 100+/- feet. Utilizes a Khatod 25 degree optic

M60LL (Low Low output)
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=9
$55.00 - Input voltage 3.8V - 9V, Current Draw 170ma at 6 volts, Led is a Cree XRE 7090
Runtime is 8 +/- hours on 2 CR123 primary batteries, solid brass heatsink construction
output is 80 +/- lumens, Utilizes a Cree 8 degree optic

M30 to fit a Surefire
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=29
$55.00 Input voltage is 1-5.5 volts, The output is approximately 235+ lumens at 3.3v+ and 160+ lumens at 3v.
The runtime is 1 1/4+ hours on one CR123 primary battery. The LED is a Cree XRE 7090.
This design utilizes a Cree 8 degree optic.

M30W (warm tint beam)
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=31
$55.00 The input voltage is 1-5.5 volts. The output is approximately 170 lumens at 3.3v+ and 120 lumens at 3v.
The runtime is 1 1/4+ hours on one CR123 primary battery. The LED is a Cree XRE 7090.
This design utilizes a Cree 8 degree optic.

M60W (warm tint beam)
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=33
$55.00 The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive.
The output is approximately 170 lumens. Runtime is 1 1/2+ hours on 2 CR123's. This design utilizes a Cree 8 degree optic.
The LED is a Cree XRE 7090.

M60WF (warm tint, flood)
http://www.malkoffdevices.com/shop2/index.php?main_page=product_info&cPath=1_8&products_id=35
$55.00 The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive.
The output is approximately 170 lumens. The runtime is 1 1/2+ hours on 2 CR123's. This design utilizes a Cree 20 degree optic.
The LED is a Cree XRE 7090.

__

** Wolf Eyes drop-ins **

Cree R2 WC LED Drop-in *Low VF*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-147-6518
$63.99 - Limited Quantities
Voltage: 3.7V-13V, Output: 280 lumens

Cree R2 WC LED 2-Mode High & Low
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-147-6524
$68.99 - Limited Quantities
Voltage: 3.7V-6V, Output: 280 lumens

Cree R2 WC LED 2-Mode Tactical Strobe
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-147-6520
$69.99 - Limited Quantities
Voltage: 3.7V-6V, Output: 280 lumens

Cree R2 WC LED 4-Mode
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-147-6526
$68.99 - Limited Quantities
Voltage: 3.7V-6V, Output: 280 lumens
Circuit sequence: 100% (280 lumens), 20% and 2% for low, strobe.

Cree R2 WC LED Drop-in *Low VF*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-147-6516
$59.99 - Limited Quantities
Voltage: 3.7V-6V, Output: 280 lumens
Note, this drop-in module is optimized to work best with a 3.7V LRB168A / 18650 Li-ion battery.

Cree Q5 LED *High Output*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-125-6437
$57.99, Voltage: 3.7V-13V, Output: 260 lumens

Cree Q5 LED *High Output*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-125-6435
$54.00, Voltage: 3.7V-6V, Output: 260 lumens

Cree Q5 LED *2-Mode* (High & Low)
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-125-6494
$64.00, Voltage: 3.7v-6v, Output: 260 lumens (maximum stage)

Cree Q5 LED *2-Mode Tactical Strobe
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-125-6475
$67.99, Voltage: 3.7v-6v, Output: 260 lumens (maximum stage)

Cree Q5 LED *4-Mode
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-125-6496
$64.00, Voltage: 3.7v-6v, Output: 260 lumens (maximum stage)
Function: 3 brightness levels (Full, 20%, 2%)+ strobe

Cree Q2 LED *High Output*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-148-6429
$44.99, Voltage: 3.7V-13V, Output: 190 lumens

Cree P4 LED
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-148-6283
$39.99, Voltage: 3.7-13v, Output: 130 lumens

Cree Q2 LED *4 mode*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-148-6352
$49.99, Voltage: 3.7-6v, Output: 190 lumens (maximum stage)
Digital circuit sequence: 100% (190 lumens), 20%, 2% and Strobe (10Hz)

Cree Q2 LED 3.7-6V *High Output*
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-148-6415
$44.99, Voltage: 3.7V-6V, Output: 190 lumens

Cree LED 3.7-6V *2-Mode* (100% & Strobe)
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-148-6360
$49.99, Voltage: 3.7v-6v. Output: 190 lumens (maximum stage)

Q2 Cree LED *2-Mode* (High & Low)
http://www.pts-flashlights.com/products/product.aspx?pid=1-139-114-148-6400
$49.99, Voltage: 3.7-6v, Output: 190 lumens (maximum stage)

__

** Lighthound.com ** -

Lighthound Cree Drop-In
http://www.lighthound.com/index.asp?...OD&ProdID=2605
$29.99 accepted voltage: 3.7V ~ 9.0V 750mAh regulator board

Q5 Cree
http://www.lighthound.com/index.asp?PageAction=VIEWPROD&ProdID=3428
$39.99, 3.7V to 9V input, 750ma

UNIQ Cree Q5 Drop-In
http://www.lighthound.com/index.asp?PageAction=VIEWPROD&ProdID=3513
$29.99, 3.7 - 15V Input, 1000mA, Textured aluminum reflector

__


**Dereelight drop ins**1S(1-stage) cree XR-E module
$32.00
- Input Range: 2.8~4.2V
- Output Range: 1.2A
- Battery Type: 1x18650,1x17670
- Features: Constant output at it's fully input range
Over discharge protection


1SM-1(1-stage multi power) Cree XR-E Q5 module (6V max)
$26.50
- Input Range: 3~6V
- Output Range: 1A
- Battery Type: 1x18650,1x17670, 2xCR123A
- Features: Constant output at 3.8~6V.


1SM-2(1-stage multi power) Cree XR-E Q5 module (16V max)
$29.00
- Input Range: 3~16V
- Output Range: 1A
- Battery Type: 1x18650, CR123A's, RCR123's
- Features: Constant output at 4.5~16V. Recommended use 2xCR123A,3xCR123A or more.


3SD(3-stage digital) Cree XR-E Q5 module
$35.00
- Input Range: 2.8~4.2V
- Output Range: 1.2A
- Battery Type: 1x18650, 1x17670
- Features: Constant output at it's fully input range
Three stage output,100%-50%-5%
Over discharge protection
Memory functon
Change level by push switch


3SM(3-stage Muti-power digital) Cree XR-E module
$35.00
- Input Range: 3~9V
- Output Range: 1.0A
- Battery Type: 1x18650, 2xCR123A, 2xRCR123
- Features: Constant output using CR123's
Three stage output,100%-50%-5%
Memory functon
Change level by push switch


3SD(3-stage digital) Cree XR-E 5A Q2 module
$36.00
- Emitter: Cree XR-E Neutral Warm White 5A Q2, it's highest rank at this tint, good color rendering, recommended for outdoor usage, especially after raining.
- Input Range: 2.8~4.2V
- Output Range: 1.2A
- Battery Type: 1x18650, 1x17670
- Features: Constant output at it's fully input range
Three stage output,100%-50%-5%
Over discharge protection
Memory functon
Change level by push switch

--

** OpticsHQ P60 Head and tailcap **

LED Drop-In and Multi-Function Tailcap Kit
http://www.opticshq.com/page/Optics/PROD/Surefire-HID/ACC-DTC-KIT
$89.99
Working voltage: 4.2-18.0v
Maximum output at the emitter approximately 220+ lumens about 2-3 hours
[FONT=Verdana,Arial,Helvetica][SIZE=-1]More than 6 hours at low output[/SIZE][/FONT]
Fits the following SureFire Lights: G2, G3, 6P, 6PD, 9P, Z2, G2Z, C2, C3, M2

LED Drop-In and Multi-Function (Reverse) Tailcap Kit
http://www.opticshq.com/page/Optics/PROD/Surefire-HID/ACC-DTC-R-KIT
$89.99
Working voltage: 4.2-18.0v
Maximum output at the emitter approximately 220+ lumens about 2-3 hours
[FONT=Verdana,Arial,Helvetica][SIZE=-1]More than 6 hours at low output[/SIZE][/FONT]
Fits the following SureFire Lights: G2, G3, 6P, 6PD, 9P, Z2, G2Z, C2, C3, M2
--

** Newexcite **

UltraFire Rebel Light Bulb with Reflector
http://www.newexcite.com/shop/index...id=126&zenid=682a08097b92cf4bb37a0e8d8065a820
$14.99 - (No voltage / output levels noted at this time)

--

* G & P *
G&P Q5 230 Lumens CREE LED Flashlight Torch Lamp GP751
$41.99 Input: 4.5v - 9v

G&P Q5 LONG FOCUS 230Lm CREE LED Flashlight Lamp GP751L
$41.99 Input: 4.5v - 9v
http://cgi.ebay.com/ws/eBayISAPI.dll...%3D4%26ps%3D42

http://cgi.ebay.com/G-P-Q5-CREE-LED...3251452QQcmdZViewItem?_trksid=p3286.m20.l1116

--

-=Surefire P60L LED Reflector Assembly=-
Max 80 lumens, Runtime up to 12 hours depending on flashlight model.
(stores listed in no particular order)
$39.00 - http://www.lapolicegear.com/sup6ledreas.html
$39.00 - http://supremeco.com.hk/catalog/product_info.php?cPath=1_26_30&products_id=4755
$39.00 - http://www.surefire.com/maxexp/main/co_disp/displ/carfnbr/254/prrfnbr/24502/P60L-LED-Assembly

** Assorted forum posts that you might find useful**
DealExtreme 1343, 1447, and Wolf-Eyes 130 Lumen Cree Module P60 Cree drop-in modules Runtimes!
REVIEW - CREE DROP IN from EBAY***VERY NICE***
Wolf Eyes cree drop-in
The post that started it Dealextreme drop in for G2, 6P, etc???


And many posts I probably missed.

Thanks everyone! :)
 
Last edited:

Lunal_Tic

Flashlight Enthusiast
Joined
Jul 29, 2004
Messages
2,875
Location
The Wilds of Tokyo
Re: p60 sized led drop-in's part 2

Any chance you could add what kind of reflector each uses to the first post? Seems like most use LOP (light orange peel) but I could have swore I saw one or two that used a non-textured reflectors but now can't find them.

-LT
 

Wolf359

Enlightened
Joined
Jan 10, 2008
Messages
231
Location
United Kingdom
Re: p60 sized led drop-in's part 2

http://www.dereelight.com/module-list.htm

Dereelight offer reflector options w/SMO for smooth, w/OP for orange peel don't remember seeing LOP light orange peel. no doubt someone will correct me if i am wrong.


http://www.dealextreme.com/details.dx/sku.11810
Cree P4 1-Mode LED Drop-In Module (3V~12V) $9.59

- Features a Cree P4 LED Emitter
- Accepted Power Input: 3V~12V
- Single mode circuitry
- Aluminum construction
- Base diameter 22.85mm, heigh 24.55mm

i was some what suprized to see a new P4 dropin but ordered one anyway :)
 
Last edited:

bspofford

Enlightened
Joined
Apr 15, 2007
Messages
824
Location
Colorado
Re: p60 sized led drop-in's part 2

Has anybody noticed how DereeLight and MTE put metallic stickers with all the necessary information on their modules?:thumbsup:

BTW, check the R2 P60 module listed on KD yesterday. You've seen the same module elsewhere for $3 more.
 

kavvika

Enlightened
Joined
Jan 30, 2007
Messages
509
Location
Chicago
Re: p60 sized led drop-in's part 2

Here's the link to the KD R2 P60 module. Better order it soon before Kai raises the price, as it's nearly $2.50 cheaper than the identical model at DX. Appears to be based on the oft-recommended DX #6090 module. I wonder what color tint it is?
 

Mike@PTS

Enlightened
Joined
Sep 10, 2005
Messages
282
Location
WA - United States of America
Re: p60 sized led drop-in's part 2

Hi guys,
Through a joint effort with ProLight Japan, PTS will be offering a limited supply of Cree R2 WC bin with Low VF drop-in LED modules. These chips were purchased direct and not supplied by Wolf Eyes. The R2 chips were sampled and tested in an independent lab with encouraging test results! Shipping should start around April 9th

I also did some spring cleaning today organizing the drop-in pages.

Here's a link: http://www.pts-flashlights.com/category.aspx?uid=1-139-114
 

Yapo

Enlightened
Joined
Jul 7, 2006
Messages
669
Location
Sydney, Australia
Re: p60 sized led drop-in's part 2

Here's the link to the KD R2 P60 module. Better order it soon before Kai raises the price, as it's nearly $2.50 cheaper than the identical model at DX. Appears to be based on the oft-recommended DX #6090 module. I wonder what color tint it is?

hmm...

Output: 117~225 Lumens (manufacturer rated)
Input Voltage Range: 3.7V~18V

...sounds like it needs 18V to run at its brightest:thinking:
 

kramer5150

Flashaholic
Joined
Sep 6, 2005
Messages
6,328
Location
Palo Alto, CA
Re: p60 sized led drop-in's part 2

hmm...

Output: 117~225 Lumens (manufacturer rated)
Input Voltage Range: 3.7V~18V

...sounds like it needs 18V to run at its brightest:thinking:

Several of us have this one on order. Unfortunately I can only test it up to 8.4V on RCRs, but another member said he would test it at various voltages up to 18.

FWIW... the 6090 produces slightly LESS light at higher voltages, than it does around 6V.

See Drewfus' review here...
https://www.candlepowerforums.com/threads/193269
 
Last edited:

kavvika

Enlightened
Joined
Jan 30, 2007
Messages
509
Location
Chicago
Re: p60 sized led drop-in's part 2

Close, Yapo. From what I understand, the 3.7v-18v "Kennan" driver board only needs ~6v for full brightness. Theres is an overhead of ~1v required for the buck circuit before it will light. Anything above the 9v of two charged 3.7v L-Ion cells or 3 3v lithium primaries and it starts to lose efficiency bucking the voltage, while current to the emitter remains unchanged. In a flashlight, this is unwanted, but in vehicle applications, it makes little difference.
 
Last edited:

matt0

Enlightened
Joined
Feb 22, 2008
Messages
389
Location
Ft. Worth, TX
Re: p60 sized led drop-in's part 2

anybody have any advice on what the dropin with the most flood would be? im looking for a very long lasting floody bulb for my g2. i thought about the M60LL but that says 8hrs and i think the SF P60L is 12hrs so im thinking about that and some sort of cheap diffuser lens
 

kramer5150

Flashaholic
Joined
Sep 6, 2005
Messages
6,328
Location
Palo Alto, CA
Re: p60 sized led drop-in's part 2

Furthermore....
I speculate those 117-225L are emitter Lumens (theoretical, taken off a datasheet)... not real-world out the front.
 

kavvika

Enlightened
Joined
Jan 30, 2007
Messages
509
Location
Chicago
Re: p60 sized led drop-in's part 2

matt, the SF brand P60L seems to be geared more towards flood with its shallow, OP reflector and SCC P4 emitter. If you're not up for spending more than $30 on a module, DX #4068 might be just the thing you're looking for, for only ~$13. There's a good review of it here, and from the low lux measurements on the DX site, it appears to be quite a good flooder. In fact, from the pictures on Light Refineries, it appears to be the same module as my beloved #1343's, just with a different emitter (never noticed that before)!
 

matt0

Enlightened
Joined
Feb 22, 2008
Messages
389
Location
Ft. Worth, TX
Re: p60 sized led drop-in's part 2

Thanks kavvika for the reply. The beamshots of that 4068 look good with a very smooth beam. Although, the lightrefineries review says 2hr runtime and I'm looking for one that will last longer (to keep in truck.) Doesn't neccessarily need to be uber-bright. I will mostly use it for in-car use (ie: looking for change under seats while in the drive-thru line or checking under the hood at night) It most likely won't be on for very long but I want it to be ready to use whenever I need it to (and I will keep extra batteries nearby)

The SF P60L may be what I need. If its not enough flood, I have heard of using satin scotch tape to diffuse the beam.


On a side note, are there any SSC P7 drop-ins out there? Or, at least, any word on the makings of one? (After some more reading, I'm about 100% sure there is NOT a P7 drop-in. From some pictures of it, it looks too big to even fit on a P60 pill)
 
Last edited:

Mercaptan

Enlightened
Joined
Oct 16, 2007
Messages
407
Re: p60 sized led drop-in's part 2

On a side note, are there any SSC P7 drop-ins out there? Or, at least, any word on the makings of one? (After some more reading, I'm about 100% sure there is NOT a P7 drop-in. From some pictures of it, it looks too big to even fit on a P60 pill)


What would be cool is if someone could make a turbo P60 head (granted it'd have to be per body) so that the diameter is slightly larger and can accommodate the pill... maybe.
 

orbital

Flashlight Enthusiast
Joined
Feb 8, 2007
Messages
4,345
Location
WI
Re: p60 sized led drop-in's part 2

Hi guys,
Through a joint effort with ProLight Japan, PTS will be offering a limited supply of Cree R2 WC bin with Low VF drop-in LED modules. These chips were purchased direct and not supplied by Wolf Eyes. The R2 chips were sampled and tested in an independent lab with encouraging test results! Shipping should start around April 9th

I also did some spring cleaning today organizing the drop-in pages.

Here's a link: http://www.pts-flashlights.com/category.aspx?uid=1-139-114

+

Hi Mike,

Great to see you've started listing these amazing R2 drop-ins
& other Wolf-Eyes lights with these emitters.

Really happy to have helped in the 'initial concept' with ProLight Japan.
It may have been a small contribution, but now you may have the very best CREE R2 emitters on the planet!!

Brian M. (mellowcat..:D)
 

Mike@PTS

Enlightened
Joined
Sep 10, 2005
Messages
282
Location
WA - United States of America
Re: p60 sized led drop-in's part 2

+

Hi Mike,

Great to see you've started listing these amazing R2 drop-ins
& other Wolf-Eyes lights with these emitters.

Really happy to have helped in the 'initial concept' with ProLight Japan.
It may have been a small contribution, but now you may have the very best CREE R2 emitters on the planet!!

Brian M. (mellowcat..:D)
Hi Brian,
Yah, thanks a bunch for that initial call inquiring about the R2s you saw on ProLight Japan's website! :thanks:

I'm soo excited, I feel like a kid before Christmas waiting for the shipment to arrive. :santa:

I hope you're enjoying that 3.7-13V drop-in we sent you! :D
 

qtaco

Newly Enlightened
Joined
Dec 1, 2007
Messages
143
Re: p60 sized led drop-in's part 2

Can someone give me some information about this module:

Cree Q5 LED 5-Mode Drop-in Module
http://www.dealextreme.com/details.dx/sku.11622
$14.28 3.6V~7.2V Input

I plan to run it off two CR123 primaries, however I just wanted to get some information about its memory (or lack there of). From the DX comments there is some confusion over how it operates, however it appears that each time you turn it on (be it after half a second or a day) it moves to the next mode in the sequence.

Can anyone confirm this? It's a shame if it's true, it would be much more useful (for me) if it started at the first mode in its sequence, or the last mode you used it on. The next mode is likely to be furthest on average from where you want to actually be!
 
Last edited:

Wolf359

Enlightened
Joined
Jan 10, 2008
Messages
231
Location
United Kingdom
Re: p60 sized led drop-in's part 2

qtaco i can comfirm it has no memory and swiches to the next mode when you turn it on sequence is low/med/high/strobe/sos. if your last mode used was high the next time you turn it on it comes on in strobe .
 

qtaco

Newly Enlightened
Joined
Dec 1, 2007
Messages
143
Re: p60 sized led drop-in's part 2

Thanks mate. I suppose it's not a big deal, but it is less then ideal for me :(
 

Dobbler

Enlightened
Joined
Feb 12, 2007
Messages
503
Re: p60 sized led drop-in's part 2

Great thread -- thanks for consolidating all that information.

Does anyone know which of these are safe for a weapon light -- can handle the shock from a rifle or shotgun -- as a drop in for a SureFire?
 
Status
Not open for further replies.
Top