How much is everybody paying for the SSC P7?

[RelativeEng]

I have noticed on some peoples builds that people are paying over $20 for a single SSC P7. Is that correct? How much did you pay?

 

[lolzertank]

The only place that sells them for less than $20 is DX, and those are C flux bin and also don't have any tint specified. :shakehead I think the one I got was J Vf and SXO tint from my eyeball.

 

[RelativeEng]

If enough people are interested, I can supply them at half that price. D-Bin

 

[Hamburger]

$10 for a D-Bin P7 ??????

Or did I understand it completely wrong ?

I already thought that the new KD Price for 10+ units is super cheap but $10 would be waaa waaa weee waaa

 

[RelativeEng]

It would depend on volume but it would definitely be cheaper than $20 for a D-Bin. And you would know exactly what color temp it is.

 

[Cemoi]

If enough people are interested, I can supply them at half that price. D-Bin

What about posting this kind offer in the Group Buys section of the Marketplace?

 

[supasizefries]

Wow, I'd be really happy if I could get p7's for less than $20.

 

[BeachBoy]

Where can you buy the D-Bins?

 

[RelativeEng]

Where can you buy the D-Bins?

I get them direct from Seoul for work. I can get any bin code.

 

[Nos]

try kaidomain, its ~20$ too

 

[old4570]

DX has one for just under $16USD ..

Just ordered my 5th one .

 

[Hamburger]

As lolzertank mentioned its a C-Bin but he means gettin a D-Bin.

I wish there where more drivers for the P7 especially for connecting to 110-230V AC

Can you post some information how many P7 would be need to get a price maybe >$15

​

 

[bstrickler]

By any chance, does anyone have any beamshots of the D bin vs C bin P7? I'm just curious as to which one is closer to cool/snow white, since nobody has a list of the different bins and the color & lumen range of them (at least, not that I've found). I've heard lots of good reports on the 2 different bins, but I haven't seen any beamshots comparing the two.

~Brian

 

[Hamburger]

C & D-Bin are brightness bins the color bins may vary

Have a look at that page

http://www.seoulsemicon.co.kr/en/product/prd/zpowerLEDp7.asp

and look for the P7 binning and labeling datasheet.

 

[bstrickler]

Ah, that makes a little more sense now.

So it sounds like I ordered the right P7 emitter (Had the option of DSXOJ or CSXOI, with DSX having higher output, so I chose that) for my application.

~Brian

 

[Dayo]

Hi what is the minimum number of P7,s that you would supply?

 

[old4570]

Well , I dont see much difference between C and D ..

Same Amps etc and same output by my light meter ..
Which is why I buy the DX ones ..

I got a Warm D***I , but aside from the warm tint , output is the same as the C bins if slightly lower .

Im not shelling out hard earned for a D bin , tried two of them , and no better than C bins , ill wait till the E bins come out , or just move to the SST-50 .

[ Looking forward to trying out the SST-50 ] Hopefully will have a flashlight up and running with the SST-50 by next week .

 

[RelativeEng]

Hi what is the minimum number of P7,s that you would supply?

The usual MOQ to get them is 1 reel which is 250

 

[degarb]

I am wondering if anyone has invented a reflector for the mce or p7 that throws like the r2?

Also, can these be wired 2 in series and 2 in parallel, so I could use a 7.2 volt source without an expensive, power sucking controller?

Also, good cri is important to me. So far, been leaning far toward rebels because of this.

 

[spencer]

I get them direct from Seoul for work. I can get any bin code.

ANY code? Any chance of a GB for some DSR0H LED's? lol