Sold/Expired Multi-Sink

[Fcdrifter]

Does your tri-XML reflector work in both C and D maglites?

Edit: never mind I see your post where you state it only fits c mags.

 

[DMC]

:paypal: for $10 from DMC


6 Connecting socket, 80C 300V 22AWG $ 6

Shipping to Worldwide $ 4


Total $10

Thanks again!

 

[simplec6]

Hi download,
Would you offer the service of modding a 7135 driver by slaving extra chips to it for higher than 2.8amps high setting? Maybe closer to a 4amps high setting?

 

[download]

simplec6, why don't you diy? It is a simple job only.

 

[simplec6]

simplec6, why don't you diy? It is a simple job only.

I may not be as good at soldering as I need to be. I suppose I could give it a try. I don't even have any 7135 drivers currently. Maybe I will order extras then in case I ruin them

 

[download]

This post may help.

Hi beam,

Basically what you need to know is this. The pins on the chips have to be linked one to another. If you look at the chip with the fat single pin facing down that is the ground, the smaller pins from left to right would then be Pos, ground, neg.





You need a wire going from the - leg of one of the chips on the main board to the slave, then a wire from one of the + legs on the main board to a + leg on the slave and then one for a ground. For ground you can use the outer gold rim of the boards, but I use the tail piece for a better connect.

Then once that is done just wire up the main board to the battery like normal.



If you are going to use a slave replacing the factory leads with some thicker wire is a good idea.

Also when you do that in order to keep from tearing the little + LED pad off some thing I ALWAYS do is this.




I strip the + wire a little longer and solder it directly to both the + pad as well as the top end of that chip next to it.


As for the modes and soldering stars it depends on what you want. If you have the shining beam driver the default setting is 3 mode. If you have a variant of this driver from another source its probly 5 mode by default.

If you want to change the mode group on the shiningbeam driver you will first have to unsolder the 2 legs on the controller board that are soldered together, dont detach them from the board, just get the solder out from between them.

Next take a razor knife and cut the electrical path to the board. You can see it under the green. The one you want to cut is the 3rd one. You can see its path just above it running to a hole.

Then make a solder connection from the star you want to the outer rim of the board ( I use a piece of wire)

Star 1= Low, Mid, High,Strobe, Sos. S2= Low, High, Strobe. S3= Low, Mid, High. S4= Low, High.

Here is a picture.
http://s10.photobucket.com/albums/a102/udownload/Flashlight/?action=view¤t=8x71354mode.jpg


Finally its not a must, however in most cases when using these boards with a slave/s for some reason they require heat sinking to stabilize the current. I usually make sure all the wires will lay perfectly flat so that I can stick all of the 7135 chips to a chunk of copper or aluminum.

If you are only powering the light by 1 li-ion or 3x nimh you may get by without it, but if the voltage is any higher than that you'll need it for sure, other wise at about the 1-2 min mark your current will fall like a rock.

 

[wannabe333]

is this kind of driver can run 3 ssc p7? instruction thanks

 

[download]

Check this out :)

http://www.candlepowerforums.com/vb/showthread.php?201392-Poorman-Mutli-Lux-setup-method

 

[wannabe333]

trying to run triple ssc p7 on my 3d mag, would like to ask anyone know what is the correct type of reflector i should use. thanks in advance.

 

[download]

The dome lens of SSC P7 is quite big.
Mostly you got to enlarge the existing small reflector's hole to fit.

Der Wichtel had a kit for it before: you may ask the old reflectors
http://www.candlepowerforums.com/vb...e-Seoul-P7-Cree-MC-E-Kit-for-Mag-D&highlight=

Now is 3x Cree XM-L
http://www.candlepowerforums.com/vb...le-Cree-XM-L-T6-Dropins-for-D-size-Mag-Lites/

 

[DMC]

:paypal: for $50 from DMC

1 Multi-Sink2 per set $25
1 Tri-XM-L Mirror Reflector (50mm x 18mmH) $18
Shipping to Worldwide $ 4
Registered mail (Tracking) $ 3

Total $50

Thanks again!

 

[download]

Thanks DMC, items were sent.
:thanks:

 

[tx101]

Hello Charles

I'll take

4 x 20mm XPG reflectors
1 x 8x7135 driver

With registered shipping

Paypal on the way


Thanks

 

[Icarus]

I take two Tri-XM-L Mirror Reflectors (50mm x 18mmH). :wave:

 

[download]

:thanks: tx101 & Icarus, :)

 

[StudFreeman]

Hi download! I'm looking at a triple XM-L build. Do you know if 3 XM-Ls mounted on individual 20mm PCBs work with your XM-L tri-flector? Will I have enough room to move the LEDs close enough together to fit into the reflector? Thanks!

 

[download]

Triple XM-L reflector is 20mm center to center.
It will fit 3x 20mm star board directly.
:)

 

[havnmonkey]

Hey Download!

2x Multi-Sink: $50
Registered mail/shipping to US: $7
Total: $57

Paypal sent, thanks!!!

 

[download]

Hi havnmonkey,

2x Multi-Sink were shipped.
:thanks:

 

[Dafoxroulz]

Hi there im new to the forums tho not to flashlights, ive just purchased my very first mag light, a 3 D cell variety and i couldnt believe how bad the standard bulb works so instantly decided on modding it, i thought about having a heatsink made or doing it myself but upon seeing these fab heatsinks decided to post here.

Do you still make and sell these?

Im located in southern BC canada.

I will be posting some of my Creations over the next few weeks.

Thanks