I build this light based on KISS Principle (Keep it Simple & Strong), Aiming for a robust & Kick *** duty light that pumps out >2000 lumens at a push of a button & delivers lots of throw as well as lots of spill .
It has two modes: "OMG I am blind" & "Dark Silence".
The throw is unmatched unless you go to Aspherical, where it becomes a toy. This isn't a toy, the suspect will be rendered blind & motionless :devil:
Specs:
(If you really want the 4 batteries to come with the light, add $20 I'll include them)
Ship in US preferred: two options:
PP gift/money owned Option will cost $12, includes shipping cost, insurance & delivery conf.
PP regular will cost $20, which includes the above & covers the 4% PP fee.
Ship international are offered at $25 S&H, there'll be no insurances or tracking # & buyer take the shipping/custom
risk. Therefore, only accept Gift/Money Owned option for international shipping. I will provide custom declaration #.
I do not do custom mods for a living, only one off mod that provides challenge & joy to the building experience, please do not ask me to make another one. See my signature for a sample of various lights I made. I only make each light one time, as I do not enjoy repeating what's already been done.
Notes:
1. Battery: One battery needs to have a "tip" to reach into the positive contact of Rebel Mag Switch. If you purchase the optional batteries, make sure to put the one that says "Top" on the top to reach the switch. You can make your own using the 4/5 Sub C with Tabs, just bend it over & cut off what you don't need, for the top one, need to trim the tab slim first & bend twice so it'll be taller tip than the rest to reach the switch positive end.
Do not use magnet, as it may slip & cause electrical short.
2. Tail Cap Dings. The Rebel LED Mag is brand new but I managed to drop the tail cap a few times & caused 3 small chip/dings the size of sesames. Sorry, but rest of the light is mint.
3. Adjusting Focus.
If you Change the lens or whatever reason you may need to take unscrew the bezel, Make sure losen the head from teh tube a bit & then tighten the bezel first that will center the reflector. Then screw the head in/out to adjust focus. The perfect focus point is that the reflector slightly above the SSR star, do not let reflector touch the star or sit on it, as the heat may deform the reflector by touching it. The Rebel reflector is plastic.
The Copper end is the Front End where the SSR-90 star is mounted down tight via Arctic Silver thermo glue.
The H22A Aluminum Mag D Sink with Carbin Fiber Trim is the Rear End.
It has two modes: "OMG I am blind" & "Dark Silence".
The throw is unmatched unless you go to Aspherical, where it becomes a toy. This isn't a toy, the suspect will be rendered blind & motionless :devil:
Specs:
- Black Mag2D Rebel LED as Host
- Copper/H22A Alu. Hybrid Heat sink, deep sunk & max length in Mag tube(It sits directly on the switch ring, can't make it any deeper)
- Mag Rebel Deep SMO reflector delivers intense & beautiful spot with ultimate throw
- 20AWD Silver coated copper wire in Teflon Sleeve
- Extreme Top Bin SSR-90 57K, GN201 (GN201 Bin has the most pleasant neutral white tint, no chance of pee green but is no longer Available,the closest to it is Fred's SSR-90 GN200 star at $60 a piece http://www.cpfmarketplace.com/mp/showthread.php?t=211967)
- 4x 4/5 Sub C 2000 mAH NIMN delivers 8Amp via direct drive >2,000 lumens at LED (1000 [email protected] 2250 lum@9A)
- Recessed Tail Cap with Resistance Mod by Copper Braid
- No Drivers, the ultimate efficiency w/o any chance of driver failure
- OTF Lux @ 1 meter in the 45,000 -50,000 lux range depends on what meter you use (Measure at 5meter & back convert to 1 meter lux)
- I am pretty sure this will blow away just about everything you have
- PVC battery sleeve is included
(If you really want the 4 batteries to come with the light, add $20 I'll include them)
Ship in US preferred: two options:
PP gift/money owned Option will cost $12, includes shipping cost, insurance & delivery conf.
PP regular will cost $20, which includes the above & covers the 4% PP fee.
Ship international are offered at $25 S&H, there'll be no insurances or tracking # & buyer take the shipping/custom
risk. Therefore, only accept Gift/Money Owned option for international shipping. I will provide custom declaration #.
I do not do custom mods for a living, only one off mod that provides challenge & joy to the building experience, please do not ask me to make another one. See my signature for a sample of various lights I made. I only make each light one time, as I do not enjoy repeating what's already been done.
Notes:
1. Battery: One battery needs to have a "tip" to reach into the positive contact of Rebel Mag Switch. If you purchase the optional batteries, make sure to put the one that says "Top" on the top to reach the switch. You can make your own using the 4/5 Sub C with Tabs, just bend it over & cut off what you don't need, for the top one, need to trim the tab slim first & bend twice so it'll be taller tip than the rest to reach the switch positive end.
Do not use magnet, as it may slip & cause electrical short.
2. Tail Cap Dings. The Rebel LED Mag is brand new but I managed to drop the tail cap a few times & caused 3 small chip/dings the size of sesames. Sorry, but rest of the light is mint.
3. Adjusting Focus.
If you Change the lens or whatever reason you may need to take unscrew the bezel, Make sure losen the head from teh tube a bit & then tighten the bezel first that will center the reflector. Then screw the head in/out to adjust focus. The perfect focus point is that the reflector slightly above the SSR star, do not let reflector touch the star or sit on it, as the heat may deform the reflector by touching it. The Rebel reflector is plastic.
The Copper end is the Front End where the SSR-90 star is mounted down tight via Arctic Silver thermo glue.
The H22A Aluminum Mag D Sink with Carbin Fiber Trim is the Rear End.
Last edited:
the led. Do not use anything other than 4x 4/5 Sub C NiMN.
