PseudoFed
Enlightened
If I get a new L1, will the circuitry and switch allow me to also use my older KL4 head?
Thanks.
Thanks.
Will Older KL4 Work on New L1 Body?
- Thread starter PseudoFed
- Start date
Help Support Candle Power Flashlight Forum
DaFABRICATA
Flashlight Enthusiast
No.
Not unless the driver is removed and the body bored to accept 2 X 123 cells.
IF you do bore it out and use 2 cells it will work fine and so will the 2-stage tailcap:thumbsup:
The KL4 will work on a 1 cell body-E1e/E1L body, but will not run long in regulation.
Do you want a smaller form factor or 2 brightness levels?
Not unless the driver is removed and the body bored to accept 2 X 123 cells.
IF you do bore it out and use 2 cells it will work fine and so will the 2-stage tailcap:thumbsup:
The KL4 will work on a 1 cell body-E1e/E1L body, but will not run long in regulation.
Do you want a smaller form factor or 2 brightness levels?
PseudoFed
Enlightened
Thought I replied last night, but my internet was flaky.
I want a tiny one cell flood machine with two levels. The KL4 currently works on my FB-1 quite well-very bright. And, I can put a McE2S tailcap on it (on a SF 1 cell body that is), and I get two levels of output, and the low is useful. Just wondering if the L1 circuitry will allow the same thing--great excuse to buy that light!
I want a tiny one cell flood machine with two levels. The KL4 currently works on my FB-1 quite well-very bright. And, I can put a McE2S tailcap on it (on a SF 1 cell body that is), and I get two levels of output, and the low is useful. Just wondering if the L1 circuitry will allow the same thing--great excuse to buy that light!
Last edited:
vtunderground
Enlightened
The issue is that the KL4 head has regulation circuitry inside, while the L1 has regulation circuitry inside the body (not the head). I'm pretty sure that the KL4 won't even screw onto the L1 body... even if it could, you'd be trying to power the LED from the L1 circuit AND the KL4 circuit, and the light still wouldn't work.
alibaba
Enlightened
Won't it fit on any E-series body (like E1E, E1L, E1B etc.)? Couldn't you use any of those bodies with a KL4 head and an RCR-123? The runtimes would probably suck but it would work no? Not sure about a 2-stage tailcap but I'm sure that there is something out there that'd work.
EDIT: or you could just get one of these: http://www.zebralight.com/index.php...ducts_id=184&zenid=rvif37qjgap8e63scb95ci0um5
EDIT: or you could just get one of these: http://www.zebralight.com/index.php...ducts_id=184&zenid=rvif37qjgap8e63scb95ci0um5
Last edited:
JNewell
Flashlight Enthusiast
KL4 + E1e body = TW4. Lots of threads here on that. Works great!
alibaba
Enlightened
sorry, dupe
DaFABRICATA
Flashlight Enthusiast
As stated before: The L1 and L2 bodie are not compatible with ANY other E-series heads UNLESS the electronics are removed.
jumpstat
Flashlight Enthusiast
The KL4 can also work with a McGizmo McClicky Pak and can be found here http://www.candlepowerforums.com/vb/showthread.php?t=202079
also any e-series compatible body and tailcaps.
also any e-series compatible body and tailcaps.
