Tk45 vs MCE ,R2,p91,p90,p60,maglite 2D

test @1M
all same setting

1pm under sun 105000lux

maglite 2D 803lux 4.5Inch light Circle

tk45
i use ni-mh or Alkaline
almost same at start
but after 5min
ni-mh is higher


Alkaline after 10min
low 63Lux 10 Inch
mid 1029lux 11 Inch
high 3950lux
tubro 10330lux(i test 4 time ,use mce and 2d test, also is this number)

tubro at start is 15600lux
ni-mh after 5min is 13500lux


Strobe 3650lux(why not use tubro..........,only high)
sos 1020lux
Warning flash 1290lux

TK45 single head with new Alkaline
mid 552lux
high 2060lux
tubro 5230lux

Tk45 1head without Reflector

low 2lux
mid 14lux
high 53lux
tubro 138lux

Tk45 3head without Reflector
mid 44
high 171
tubro 446

6p d26 Mce k bin [email protected] high 3300lux 10 Inch
low 730lux

9p d26 R2 17500*2 @ 1A 5280lux 5Inch


p91(2*17500, 2.85A) 10230lux(i can't Imagine so bright, i buy it 20years ago)
p90(2*17500, 1.02A) 4640lux
gp (3.7v 17670) 1270lux

3*aa 410 lux 7inch

E09 p4 tir 340lux 11 inch

becaus too much photo
i need edit

i will post
pls wait me 5hr

Tk45
new Alkaline
start at 12.69v
low 0.01A 12.68V
mid 0.07A 12.50V
high 0.27A 12.10V
tubro 0.97A, 10.90V

I ALSO TEST OLD NI-MH
START AT 10.96V
TUBRO IS 1.27A 8.90V


Strobe 0.24A 10.15V
sos 0.08A 10.43V
Warning flash 0.07A 10.44V

when i put in new Alkaline

i try 3 time mabye the volt is high
it go safe mode
3head light at low
only on and off
can't change mode
i need take out the head ,and install again

than ok

open box


19.1mm(like AAhead, not d26.5)

the manual
http://i119.photobucket.com/albu ... girl/tk45/tk451.jpg
http://i119.photobucket.com/albu ... girl/tk45/tk452.jpg

just like maglite 2D size , u can put 32500, but TK45 can't use

sp 6p

left D26.5 ,right TK45


up D26.5, down TK45


8AA, 8p1S max 13V
+- at same side
the body don't need touch Negative

head ,body,cover
body can up side down install
the only Effect in can't put it back to box


very thin


the Correct is 37.5mm, i little big for 8AA, but it's better than too small
can't put the battery inside



only body is 119mm

body with cover is 121.3mm

can easy turn out

6p inside Tk45, and it can easy stand


8AA same height as 2D size


a littel bit high, can't use 32500 at Tk45


the test will Include GP 3.7, SF 90,p91, i buy almost 20years


mod MCE k bin 2.0A to 2.8A @one 17670

magliht 2D





tk45,low ,one head


mid, 3 head

tk45, high 3head



tk45, tubro 3head



maglite 2D vs tk45 low


tk45 mid


tk45 high


tk45 tubro



6p mce k bin low vs tk45 low


tk45 mid


tk45 high


tk45 tubro



6p mce k bin 2.8A vs tk45 low


tk45 mid


tk45 high


tk45 tubro


9p R2 1A vs tk45 low


tk45 mid

tk45 high

tk45 tubro

test place 1

brand new sanyo eneloop 1



test with,

brandnew sanyo eneloop
non-changed test
09--11UC


start at 1.321V
1A dischange by imax B6 ,cut at 0.8V
eneloop1 1458mah first 60min is 0.99v-0.96V
eneloop2 1378mah first 60min is 0.97v-0.94V, 60min-83min is 0.93V



room temperature 31-32C
eneloop1 34.1c-35c
eneloop2 36C-37C

now eneloop1 change at 2A
eneloop2 change at 0.2A

after 24hr, i will test again